LevelOne FCS-0030, WCS-0030 User Manual

FCS-0030

H.264 MegaPixel PIR Lighting IP Camera

WCS-0030

Wireless H.264 MegaPixel PIR Lighting IP Camera

Ver 1.0

LevelOne

User Manual

- -

Product name: Megapixel Cube Network Camera (WCS-0030/FCS-0030)

Release Date: 2010/02/01

Manual Revision: V1.x Firmware 1.x.x.x

Web site:

www.level1.com

Default Settings

IP Address DHCP

Username admin

Password admin

General Public License

This product incorporates open source code into the software and therefore falls under
the guidelines governed by the General Public License (GPL) agreement.

Adhering to the GPL requirements, the open source code and open source license for
the source code are available for free download at http://global.level1.com.

If you would like a copy of the GPL or other open source code in this software on a
physical CD medium, LevelOne (Digital Data Communications) offers to mail this CD to
you upon request, for a price of US$9.99 plus the cost of shipping.

- -

Table of Contents

Before You Use This Product ............................................................................. 0

Cube Network Camera Overview......................................................................... 1

Device Appearance Description .......................................................................... 3

LED Behavior ............................................................................................... 4

Installation ................................................................................................... 6

System Requirements..........................................................................................................6

Camera Connection.............................................................................................................7

Software installation.............................................................................................................8

Access to the Network Camera......................................................................... 15

Check Network Settings.....................................................................................................15

Add Password to prevent Unauthorized Access.................................................................15

Authentication .................................................................................. 16

Installing plug-in.................................................................................................................17

Live View................................................................................................... 18

Configuration ............................................................................................ 21

Administrators can access the configuration page. .................................................. 21

Camera/Video/Audio..........................................................................................................21

Camera ......................................................................................... 21

Video ............................................................................................ 23

Audio............................................................................................ 26

Multicast........................................................................................ 27

Network .............................................................................................................................28

IP Setting....................................................................................... 28

UPnP ............................................................................................ 29

DDNS (dynamic domain name service)..................................................... 30

TZO .............................................................................................. 31

Easy Link....................................................................................... 31

Wireless.............................................................................................................................32

Basic Settings................................................................................. 32

Security......................................................................................... 32

WEP ............................................................................................. 32

Site Survey..................................................................................... 33

WPA-Personal................................................................................. 34

WPA2-Personal ............................................................................... 35

Advanced Settings ........................................................................... 35

Wi-Fi Protected Setup ....................................................................... 36

- -

HTTP/HTTPS................................................................................... 37

Event.................................................................................................................................37

Motion Detection ............................................................................. 37

Notification setting........................................................................... 38

Scheduled Event..............................................................................................................42

PIR............................................................................................... 43

System Log .................................................................................... 44

Date & Time Settings ........................................................................ 45

Device Information ........................................................................... 46

Maintenance.....................................................................................................................48

User Management ............................................................................ 48

IP Filter ......................................................................................... 49

Firmware Upgrade............................................................................ 49

Configuration.................................................................................. 50

Reset to default ............................................................................... 50

Before You Use This Product

The use of surveillance devices may be prohibited by law in your country. The Network

Camera is not only a high-performance web-ready camera but also can be part of a

flexible surveillance system. It is the user’s responsibility to ensure that the operation of

such devices is legal before installing this unit for its intended use.

It is important to first verify that all contents received are complete according to the list

in the "Package Contents" chapter. Take notice of the warnings in “Quick installation

guide” before the Network Camera is installed, then carefully read and follow the

instructions in the “Installation” chapter to avoid damages due to faulty assembly and

installation.

Package Contents

 Camera
 CD Manual/utility
 QIG
 Camera Stand
 Power Adapter

- 1 -

Cube Network Camera Overview

Compact designed Level1 FCS-0030/WCS-0030 offers high video quality surveillance

solution for residences and small businesses. Unlike general webcam, Level1 FCS-0030/

WCS-0030 camera is a standalone complete system that does not need to be connected to a

computer. The built-in web server allows user to access over local area network (LAN) and

through the internet via a web browser for live viewing and intercom functions. Enhanced

facility for user, live viewing can also be supported via 3GPP phone and MSN.

Wireless capacity makes it easy to mount the device anywhere such as wall or desktop.

802.11b/g/n wireless with WPS and Ethernet connectivity can be integrated with an existing

network environment. “Easy Installation Wizard” also allows user to configure device easily,

even without IT background. Furthermore, the fashionable and streamline shape let the

FCS-0030/ WCS-0030 not only a network camera, but also a decoration device.

The FCS-0030/WCS-0030 helps user monitor closely on family members, pets, offices,

properties or anything valuables.

Pet monitor - Office workers can monitor pet in the house anytime, and also deliver voice by

built-in speaker to let pet feel that the Owner is nearby

Residence monitor - Built-in PIR sensor can detect stranger intruding, which can trigger

illumination LED, and send alert with snapshot in email or MMS to user’s portable device.

Labor monitor - Labor can be monitored when user is outside, and images also can be

recorded and stored in micro SD.

- 2 -

The elderly and baby care - The elderly and baby can be cared easily by live view and

intercom.

Small office surveillance - Employees working status can be monitored by portal device.

- 3 -

Device Appearance Description

< Front & Rear view >

<Side view>

Power Connector

Reset Button

Ethernet RJ45

10/100 Socket

Illumination LED

Speaker

PIR

Built-in

Microphone

Vari-focal Lens

Micro SD slot

Privacy button

WPS button

(WCS-0030 Only)

Power LED

WPS LED (WCS-0030 Only)

Wireless LED (WCS-0030 only)

Internet LED

Privacy LED

- 4 -

LED Behavior

Function LED Behavior Description Remark

Power Steady On Normal Operation Top

(Blue)

Power Unlighted Power off Top

(Blue)

Status

Steady On

1. Connect to switch by

Ethernet or WiFi.

2. Reset to default.

Second (Blue)

Status

Unlighted

1. Power off

2. No connection

Second (Blue)

Status

1.While F/W upgrading

2.While WiFi site survey

performing

Second (Blue)

Status

Blinking

1.While network

connection in progress

2. Restoring settings.

Second (Blue)

Internet

Steady On Connect to Internet Third (Blue)

Internet

Unlighted

1. Power off

2. No connection

Third (Blue)

WPS

WPS in progress Fourth (Blue)

WPS

WPS Error Fourth (Blue)

- 5 -

WPS

Session overlap detected Fourth (Blue)

WPS

WPS Success Fourth (Blue)

Privacy Steady On

Privacy mask active Bottom

Privacy Unlighted

Privacy mask inactive Bottom

Hardware Reset

The reset button is used to reset the system or restore the factory default settings. Sometimes
resetting the system can return the camera to normal operation. If the problems remain after
reset, please restore the factory settings and install it again.
Reboot - Please press and release the indented reset button within 1 second with paper clip
or thin object. Wait for the network camera to reboot.
Restore - Please press and hold the reset button until the status of LED turns off. It takes
about 10 seconds. Please note that all settings will be restored to factory default. Upon
successful restore, the status of LED will be blue again during normal operation.

Micro-SD Card Capacity

The network camera is compliant with Micro-SD/SDHC (Maximum 32GB) cards.

Reset Button

- 6 -

Installation

System Requirements

Operating System

Microsoft Windows XP Home Edition SP2

Microsoft Windows XP Professional SP2

Computer

IBM PC/AT Compatible

CPU

Pentium 3GHz or faster

Memory

1024 MB or more

Monitor

1024 x 768 pixels or more, 24-bit True color or better

Network Interface

10/100Mbps Network interface card must be installed

Web Browser

Microsoft Internet Explorer 6.0 SP2

CD-ROM Drive

It is necessary to read the operating instructions in the provided CD-ROM.

Adobe Reader

It is necessary to read the operating instructions in the provided CD-ROM.

 Audio function will not be working if a sound card is uninstalled on PC. Audio may be

interrupted depending on the network environment.

- 7 -

Camera Connection

Basic Connection

1. Connect the supplied power cable from the camera to the power outlet.

2. Connect the camera to a switch via Ethernet cable.

Please check your product package contains all the accessories listed in the foregoing

Package Contents. Upon powering up, the power LED will become lighted first and then

the device will go through booting process. The status LED will be steady amber for getting

IP address. After getting IP Address, the link LED will blink orange while network

connection is processing.

- 8 -

Software installation

In this manual, "User" refers to whoever has access to the Network Camera, and

"Administrator" refers to the person who can configure the Network Camera and grant user

access to the camera.

After hardware connection checking, the users can run the Installation Wizard program

included in the product CDROM to automatically search for the Network Camera in the

Intranet. There may be many Network Cameras in the local network. Users can differentiate

the Network Cameras with the serial number. The serial number is printed on the labels on the

carton and the bottom of the Network Camera body.

1. Insert the Installation CD into the CD-ROM driver. Click install and shows the welcome
screen. Follow the steps to install the Installation wizard on user’s computer.

- 9 -

- 10 -

- 11 -

2. Do not check the box if user would like to check the hardware installation settings,
Otherwise click “Skip the hardware installation” to skip the hardware connection checking,
the program will automatically search for the Network Camera in the Intranet.
Click “Start” to continue.

- 12 -

3. Select the Network Camera from the survey list and enter the user name and password.
The user name and password are assigned as “admin/admin”.

- 13 -

4. Setting the Network Camera IP address

User can either select simple mode or professional mode for network camera IP setting. If
simple mode is selected, the easy configuration program will set up the connection
automatically. If professional mode is selected, the user will need to configure the IP
manually, The DHCP setting is recommended. If user wants to set IP address manually,
please refer to the product user manual.

- 14 -

5. Please make sure the internet connection is ready then start to do the internet discovery,
otherwise click “Skip” to finish the setting.

The default domain name is MAC address; you can also register with your own name
on-line.

6. After finish setting, the connection successful or fail showed. If connection failed, user can
either try again or quit the installation. User can either select “Run PC-NVR” or "Start Web
GUI" to continue or click “X” on the top right of the screen to finish the installation.

Once installation is completed, the Administrator should proceed to the next section

"Access to the Network Camera" for necessary checks and configurations.

- 15 -

Access to the Network Camera

Check Network Settings

The Network Camera can be connected either before or immediately after software

installation onto the Local Area Network. The Administrator should complete the network

settings on the configuration page, including the correct subnet mask and IP address of

gateway and DNS. Ask your network administrator or Internet service provider for the detail

information.

Add Password to prevent Unauthorized Access

The Administrator should immediately implement a new password as a matter of

prudent security practice. The user name and password for the Administrator are assigned

as “admin/admin”. Once the Administrator’s password is saved, the Network Camera will ask

for the user’s name and password before each access. The Administrator can set up a

maximum of ten (10) user accounts. Each user can access the Network Camera except to

perform system configuration. Once the password is changed, the browser will display an

authentication window to ask for the new password. Once the password is set, there is no

provision to recover the Administrator’s password. The only option is to restore to

the original factory default settings.

- 16 -

Authentication

After opening the Web browser and typing in the URL of the Network Camera, a dialogue

window pops up to request a username and password. The user name and password for the

Administrator are assigned as “admin/admin”. Upon successful authentication, the following

figure is displayed.

The foreground is the login window and the background shows the message if authentication

fails. The user may check the option box to save the password for future convenience. This

option is not available to the Administrator for obvious reason.

- 17 -

Installing plug-in

For the initial access to the Network Camera in Windows, the web browser may prompt for

permission to install a new plug-in for the Network Camera on the Internet Explorer.

Permission request depends on the Internet security settings of the user’s PC or notebook. If

the highest security level is set, the computer may prohibit any installation and execution

attempt. This plug-in has been registered for certificate and is used to display the video in the

browser. Users may click on to proceed. If the web browser does not allow the

user to continue to install, check the Internet security option and lower the security levels or

contact your IT or networking supervisor for help.

- 18 -

Live View

Live View is the default page that opens when accessing the Network Camera. Live video is

displayed directly in the browser window.

 Stream1/Stream2 Channels

The network camera offers simultaneous dual stream for optimized quality and bandwidth. To

configure the codec compression and video resolution, please go to the

Configuration->Camera/video/audio->Video to make the changes, or refer to the Video

configuration page.

 TCP/UDP protocol

TCP - This protocol guarantees the complete delivery of streaming data and thus provides

- 19 -

better video quality. Nevertheless, the downside with this protocol is that its real-time effect is

not as good as that of the UDP protocol.

UDP - This protocol allows for more real-time audio and video streams. However, network

packets may be lost due to network burst traffic and images may be broken. Activate UDP

connection when occasions require time-sensitive responses and the video quality is less

important.

LED Control

Select from the drop-down list to adjust the brightness of the camera’s LED. Click Apply or

Reset to take effect.

/ Recording on/off: shows the status of recording video

/ MIC on /off: shows the status of MIC volume.

/ MD on/off: shows the status of Motion Detection

 Camera Control Panel - There are two slider bars and eight control buttons on the remote

controller. They are describe as below:

 Brightness and Mic volume adjustment - Drag the slider bar to adjust the image

brightness level and Mic volume. Click “Default” for default brightness setting and “Mute”

for no sound. For more Audio setting, please refer to the Audio configuration on page 22.

 Speaker –You can output the audio form the computer’s audio input terminal to the

camera’s built-in speaker output.

Play or Stop - Click this button to play or stop the video.

Recording - Click this button to record video to your computer.

- 20 -

Snapshot - Click this button to capture and save still images.

Digital Zoom - Click this button to enable the zoom operation.

Mirror - horizontally reflect the display of the live video.

Flip - vertically reflect the display of the live video.

Real Size - click this button to view the object in real size. Press this button again

to switch back to normal mode.

Full Screen - Click this button to switch to full screen mode. Press “Esc” key to

switch back to normal mode.

Motion Detection Alert: Click this button to enable motion detection alert function.

NOTE - The <Video Control Panel> function has no effect on the recorded video. Whatever

changes made to the <Video Control Panel> will not be applied to the recorded video.

- 21 -

Configuration

Click Configuration on the main page to enter the camera setting pages. Note that only

Administrators can access the configuration page.

Camera/Video/Audio

Camera

- 22 -

Camera Setting

Brightness - Drag the slider bar to adjust the image brightness level, which ranges from -5 to

+5.

Contrast - Drag the slider bar to adjust the image contrast level, which ranges from -5 to +5.

Sharpness - Drag the slider bar to adjust the image sharpness level, which ranges from -5 to

+5.

Saturation - Drag the slider bar to adjust the image saturation level, which ranges from -5 to

+5.

Environment - User can look for a place that best suits your needs, either outdoor or indoor.

Flicker-Free - While flicker-free technology eliminates the problem of flicker,

it can cause slight judder on fast moving images or blurring problems; fast scrolling text for

example may blur.

NOTE - The "Environment" setting adjusts the sampling rate of the camera sensor to

achieve Flicker-free effect on the video.

The sampling rate, however, may not work best with the frame rate chosen in the "Video"

setting.

For best recording experience, configure your IP camera to one of the following frame rates

based on the Environment used:

Environment / Flicker-Free Frame Rate

------------------------------------ ---------------------------------­Outdoor or Indoor ( 50Hz ) 25, 10, 7, 5, 3, 2

Indoor ( 60 Hz ) 20, 10, 7, 5, 3, 2

Mirror and Flip

Mirror - Enable to horizontally reflect the display of the live video.

- 23 -

Flip - Enable to vertically reflect the display of the live video.

.

Video

You can set up two separate streams for the Network Camera for different viewing devices.

Stream 1 & Stream 2

Video Codec - The Network Camera offers three choices of video codec standards for

real-time viewing: H.264, MPEG-4 and MJPEG.

Video Resolution - Select from the drop down list to choose the best resolution that fit

your need.

Frame Rate - Select from the drop down list of the frame rate, which ranges from 2 to 30

fps when H.264 or MJPEG is selected. Only 3 to 15 fps can be chosen when MPEG-4 is

- 24 -

selected. Set the frame rate higher for a smoother video quality.

Video quality and bit rate - User can either choose “quality” or “bitrate” to

control the video quality with video codec at H.264 or MPEG4. Only “quality” can

be chosen when video codec at MJPEG is selected. Set the bitrate higher for a

better video quality. However, high bitrate may cost high network bandwidth

Resources.

The video qualities are selectable at the following settings: SoSo, OK, Not Bad, Medium,

Standard, and Good.

HTTP Transport – Enable to use HTTP protocol for video/audio communication.

Click Apply or Reset to take effect.

Video Overlay

Video Overlay - Check to enable the timestamp function and select display position from the

drop-down list if user wants date and time to be shown on the screen of the live video. User may

also enable and enter the video description in text box; and select display position from the

drop-down list if user wants to make a note about the network camera.

Click Apply or Reset to take effect.

NOTE - The video overlay only takes effect in stream 1.

- 25 -

RTSP Server

To utilize RTSP authentication, make sure that you have set a password for the Network
Camera first.
RTSP (Real-Time Streaming Protocol) controls the delivery of streaming media. By default the
port number is set to 554.
Authentication - Depending on your network security requirements, the Network Camera
provides two types of security settings for streaming via RTSP protocol: NONE and DIGEST.
If DIGEST authentication is selected, user credentials are encrypted using MD5 algorithm, thus
providing better protection against unauthorized access.

Save file folder

Recording folder path - The destination for saving the recording video files. Click browse

to specify the saving path.

Snapshot folder path - The destination for saving the snapshot files. Click browse to

specify the saving path.

- 26 -

Click Apply or Reset to take effect.

Audio

You can set up two separate streams for the Network Camera for different viewing devices.

User can either enable or disable the audio function. If audio enable is selected, select the

Audio codec from the drop down list.

Advanced

Echo cancellation Enabled: Enable to avoid an echo.

Click Apply or Reset to take effect.

- 27 -

Multicast

Multicast addressing is a network technology for the delivery of information to a group of

destinations simultaneously using the most efficient strategy to deliver the messages over each

link of the network only once, creating copies only when the links to the multiple destinations

split. You can either enable or disable the stream1or stream2 for the Network Camera. The

default value for multicast address and port are 234.1.2.3 and 10000. Use different port number

for different stream. Use default value is recommended if you are not sure how to setting.

Click Apply or Reset to take effect.

- 28 -

Network

IP Setting

This section explains how to configure wired network connection for the Network Camera.

There are several ways to setup the Network Camera over the Internet. The first way is to

obtain an available dynamic IP address assigned by a DHCP server. The second way is to

utilize a static IP. The third way is to use PPPoE.

- 29 -

DHCP - Get IP address automatically. Select this option to obtain an available dynamic IP

address assigned by a DHCP server each time the camera is connected to the LAN.

Static IP - Select this option to manually assign a static IP address to the Network Camera.

Enter the static IP address, Subnet mask, Default Gateway, Primary and Secondary DNS

provided by your ISP.

PPPoE - (Point-to-point over Ethernet): Choose this connection type if you are connected

to the Internet via a DSL Line. Note that to utilize this feature, it requires an account

provided by your ISP. Enter the user name and password provided by your ISP.

Click Apply or Reset to take effect.

UPnP

Only UPnP discovery supported. Enable this function to allow the user to search for devices of

interest on the network. Enter the UPnP name as you wish to show on the intranet.

- 30 -

Click Apply or Reset to take effect.

DDNS (dynamic domain name service)

DynDNS - Enable the DDNS service allows your Network Camera, especially when assigned

with a dynamic IP address, to have a fixed host and domain name. Note that before utilizing this

function; please apply a dynamic domain account first. Enter the username, password and

hostname when enabled the DDNS.

Click Apply or Reset to take effect.

- 31 -

TZO

TZO - TZO is one kind of the DDNS providers. User can refer to the TZO.com: visit

http://www.tzo.com/ to apply a dynamic domain account when selecting this DDNS provider.

Enter the e-mail address, password and domain name when enabled the TZO.

Click Apply or Reset to take effect.

Easy Link

Easy Link – the IP camera had bundle with free Level1DNSTM service that allows user to

remote access the IP camera via internet. The default domain name is MAC address, you can

also register your own name on-line but it have to check the available first. The status will

show the connection with Level1DNSTM service.

Notice: Please make sure the internet connection is ready first!

- 32 -

Wireless

Basic Settings

Network Name (SSID) - The SSID is the network name shared among all points in a wireless
network. The SSID must be identical for all devices in the wireless network. It is case-sensitive
and can be up to 32 characters in length. Make sure this setting is the same for all points in your
wireless network.
Wireless devices have a default wireless network name or Service Set Identifier (SSID) set by
the factory,. Level1 wireless products use Level1 as the default wireless network name. You
should change the wireless network name to something unique to distinguish your wireless
network from other wireless networks that may exist around you, but do not use personal
information, because this information may be available for anyone to see when browsing for
wireless networks.

Security

Encryption protects data transmitted over a wireless network. Wi-Fi Protected Access
(WPA-Personal/WPA2-personal) and Wired Equivalent Privacy (WEP) offer different levels of
security for wireless communication. A network encrypted with WPA-Personal/WPA2-personal
is more secure than a network encrypted with WEP, because WPA-Personal/WPA2-personal
uses dynamic key encryption. To protect the information as it passes over the airwaves, you
should enable the highest level of encryption supported by your network equipment.

Select the security method for your wireless network. If you do not want to use wireless security,
keep the default, Disabled.

WEP

- 33 -

WEP is a basic encryption method that is not as secure as WPA.

Tx Key - Select a key from the drop-down menu.
WEP Encryption: Select a level of WEP encryption, 64 bits 10 hex digits or 128 bits 26 hex
digits. The default is 64 bits 10 hex digits.
Key 1-4 - Enter the WEP key(s) manually
Authentication Type - The default is set to open system, which allows either Shared Key or Auto
authentication to be used. With Open System authentication, the sender and the recipient do
NOT use a WEP key for authentication. With Shared Key authentication, the sender and
recipient use a WEP key for authentication.
Network Type - Select Infrastructure if your network consists of both wired and wireless devices

that communicate through a central device, such as an access point. Select Ad-hoc if your
network consists of only wireless devices that communicate with each other directly.

Click Apply or Reset to take effect.

Site Survey

SSID Broadcast, when wireless clients survey the local area for wireless networks to associate
with, they will detect the SSID broadcast of the camera.

- 34 -

WPA-Personal

WPA supports two encryption methods, TKIP and AES, with dynamic encryption keys. Select
the type of algorithm, TKIP or AES. The default is TKIP.
Shared Key - Enter the key shared between the Router and the server keys. Enter a
passphrase of 8-63 characters.
Network Type - Select Infrastructure if your network consists of both wired and wireless devices
that communicate through a central device, such as an access point. Select Ad-hoc if your
network consists of only wireless devices that communicate with each other directly.
Click Apply or Reset to take effect.

- 35 -

WPA2-Personal

WPA2 supports AES encryption methods with dynamic encryption keys.
Shared Key - Enter the key shared between the Router and the server keys. Enter a pass
phrase of 8-63 characters.

NOTE: If you are using WPA or WPA2, each device in your wireless network MUST use the
same WPA or WPA2 method and shared key, or else the network will not function properly.

Advanced Settings

- 36 -

Network Mode - From this drop-down menu, you can select the wireless standards running on
your network. If you have both Wireless-B, Wireless-G and Wireless-N (2.4GHz) devices in your
network, keep the default setting, Mixed. If you have both Wireless-B, Wireless-G devices in
your network, select BG-Mixed. If you have only Wireless-B devices, select Wireless-B Only. If
you have only Wireless-G devices, select Wireless-G Only. If you have only Wireless-N
(2.4GHz) devices, select Wireless-N Only.
Radio Band - The settings are available for the Auto-20/40MHz channel and Standard-20 MHz
channel. The Auto-20/40MHz channel set up a network using the 20/40MHz band, and the
Standard-20 MHz channel set up a network using the 20 MHz band.
Enable WMM (802.1e QoS) - WMM is a wireless Quality of Service feature that improves quality
for audio, video, and voice applications by prioritizing wireless traffic. To use this feature, your
wireless client devices in your network must support Wireless WMM. If you would like to disable
this feature, select Disabled. Otherwise, keep the default, Enabled.

Wi-Fi Protected Setup

Use this method if your client device has a Wi-Fi Protected Setup PIN number.

1. Enter the PIN number and SSID from the device in the field on the screen.

Click Apply or Reset to take effect.

- 37 -

HTTP/HTTPS

HTTP - This protocol allows the same quality as TCP protocol without needing to open specific
ports for streaming under some network environments. Users inside a firewall can utilize this
protocol to allow streaming data through.
HTTPS - (Hypertext Transfer Protocol over SSL): This section explains how to enable
authentication and encrypted communication over SSL (Secure Socket Layer). It helps protect
streaming data transmission over the Internet on higher security level.
Click to enable and click Apply or Reset to take effect.

Event

Motion Detection

Motion can be detected by measuring change in speed or vector of an object or objects in the

field of view. This section explains how to configure the Network Camera to enable motion

detection. There are three motion detection windows can be configured.

- 38 -

Detection Setting - Select and enable the motion detection windows function. Easier to

trigger event by higher the sensitivity value and lower the Threshold value.

Notification - To react in response to particular events. A typical application is that when a
motion is detected, the Network Camera sends buffered images to a FTP server, Samba,
SMTP or HTTP as notifications. In this page, you can specify which notification messages will
be sent when a trigger is activated. You can configure the Network Camera to send video
streaming URL or video clips to your email address or FTP site.

Click Apply or Reset to take effect.

Notification setting

When an event is triggered, you can specify what kind of action will be performed. You can

- 39 -

attach video clip to your email address, FTP site, samba or HTTP.

FTP - File Transfer Protocol (FTP) is often used as an application component to

automatically transfer files for program internal functions. Select to send the media files to a

FTP server when a trigger is activated. Enter the FTP IP address or hostname; by default,

the FTP port server is set to 21, enter account name and password to configure the setting.

Click Apply or Reset to take effect.

SMTP - Select to send the media files via Email when a trigger is activated.

From - Enter the email address of the sender.

To - Enter the email address of the recipient. Many recipients are separated by commas.

My name - The title shown in the email.

Subject - Enter the subject of the email.

Attached - There are two choices of media types available: video streaming URL and video

clip.

SMTP Server and port number - Enter the server host name and port number of the email

server.

Authentication - Select the authentication type from the drop-down list.

Email Account - Enter the user name of the email account if necessary.

- 40 -

Email Password - Enter the password of the email account if necessary.

Click Apply or Reset to take effect.

Samba - Select to send the network file system media files via network neighborhood when

a trigger is activated.

IP Address - Enter the IP address of the samba server.

User Name - Enter the user name of the samba server.

Password - Enter the password of the samba server.

Workgroup - Enter the workgroup of the samba server.

Share DIR - Enter the share DIR of the samba server.

- 41 -

Click Apply or Reset to take effect.

HTTP - Select to send the media files to a HTTP server when a trigger is activated.

URL - Enter the URL of the HTTP server.

Message: Enter the message that informs you when a trigger is activated.

- 42 -

Scheduled Event

Click New to open the recording setting page. In this page, you can define the recording
schedule and recording capacity.

Name - Enter a descriptive name for the recording setting.

Event - Select from the drop-down menu for the recording or rebooting event.

Time - Specify the recording duration.

■ Select the time for recording in 24-hr time format. End time must be more than start time.

■ Select the days on weekly basis.

When completed, Click Add to have recording name appears in the recording list on the
recording page. Select Enabled; the system begins recording and send recorded file to the
Network Storage. To edit a recording setting; click Edit to modify. Upon the completion, click
update to finish the modification. To remove a recording setting from the list, select a recording
name from the list and then click Delete. Click New to add more events.

- 43 -

PIR

Enable PIR sensor to detect a moving infrared object such as a person in the dark.
Sensitivity - is used to adjust the sensitivity of the PIR Sensor from 10 - 100%. The default
sensitivity is 50%.
By increasing the sensitivity, the range of the PIR Sensor is also increased. The PIR Sensor can
be configured to detect movement in the dark up a maximum range of 6 meters. Select from the
drop-down list to adjust the PIR Sensor’s sensitivity.

Notification
Light - to illuminate the scene. The brightness of light source can be manually selected from the
drop-down list.

Click Apply or Reset to take effect.

- 44 -

System

System Log

Log - To send a system log to the network camera when a trigger is activated.

This page displays the system’s log in chronological order. The system log is stored in the

Network Camera’s buffer area and will be overwritten when reaching a certain amount.

Click Retrieve to retrieve the log, or click Save to file to save the file in the specify location.

- 45 -

Date & Time Settings

Manual - The user enters the date and time manually.

Clone from PC - Sync with computer time; click clone to synchronize the date and time of

the Network Camera with the local computer. The read-only date and time of the PC is

displayed as updated.

NTP - Select to update the time with the NTP server on hourly, daily, weekly, or monthly

basis.

Time Zone - According to your local time zone, select one from the drop-down list.

NTP Server 1 and Server 2 - Enter the address of the NTP server.

Daylight Saving: Enable this option to retain the Daylight Saving Time changes automatically.

Click Apply or Reset to take effect.

- 46 -

Device Information

Video/Audio Setting - To view the entire video/audio setting information about the network

camera.

Network Setting - To view the entire network setting information about the network camera.

- 47 -

System Information - To view the entire system information about the network camera.

Storage Management - To view the entire recorded files in SD card.

Click Remove to safely remove the storage device.

Click Reload to view the list.

- 48 -

Maintenance

User Management

This section explains how to enable password protection and create multiple accounts.

Privilege Setting - Enter the new user’s name and password. Select the privilege for

new user account. Click Add to take effect. The administrator account name is “admin”,

which is permanent and can not be deleted.

Access rights are sorted as following (Viewer, Administrator and Remote Viewer). Only

administrators can access the Configuration page. Viewers can access the main page for

live viewing only. The privilege of Remote Viewer is same as viewer except TCP protocol

can only be selected for live viewing page. Administrators can add up to 10 user accounts.

Administrator also can change user’s access rights or delete user accounts. Select an

existing account to modify and make necessary changes; then click Update or Delete to

take effect.

- 49 -

IP Filter

IP Filter - Enable the IP filter and set of allow or deny IP address range to server. Click

Add to list to add the IP range to the IP filter list.

Click Apply or Reset to take effect.

Firmware Upgrade

This feature allows you to upgrade the firmware on your Network Camera. It takes about few

minutes to complete the process. Note that do not power off the Network Camera during the

upgrade.

Upgrade - Click Browse… and specify the firmware file. Click Upgrade. The Network

Camera starts to upgrade and will reboot automatically when the upgrade completes.

- 50 -

Configuration

This feature allows you to export/import the configuration files of the network camera.

Import/Export - Click export to pop up a dialog to indicate the location and file to export.

Click browse to indicate the location and file of the camera configuration and click import

to import the configuration file back into the network camera.

Reset to default

Reset to default - Click Reset to restore the network camera to factory default setting.

Reboot

This feature allows you to reboot the Network Camera, which takes about one minute to
complete. When completed, the live video page will be displayed in your browser. The following
message will show during the rebooting process.

- 51 -