Levana Astra PTZ User Manual [en, es, fr]

Astra

MANUAL MANUEL MANUAL

™

Digital Baby Video Monitor Moniteur vidéo bébé numérique Video Monitor Digital para Bebé

CAUTION: Keep small parts away from children. ATTENTION: Gardez les petites pièces hors de la portée des enfants. PRECAUCIÓN: Mantenga las piezas pequeñas fuera del alcance de los niños.

mylevana.com

SAFETY WARNINGS

CAUTION: Keep small parts away from children.

Strangulation Hazard: Children can become entangled in

cords. Power cords should be kept more than 3 feet away from the crib and baby’s reach at all times. Baby monitors and cameras with power cords should never be hung on or near the crib.

This product is not a toy and should be kept out of

children’s reach.

This product contains small parts. Exercise care when

unpacking and assembling the product.

Read and Keep Instructions: All the safety and operating

instructions should be read before the video baby monitor is operated.

Water and Moisture: This product is designed for indoor use only. The unit should not be exposed to rain, moisture, dripping or splashing. No objects ﬁlled with liquid should be placed on top of, or beside the product, such as a glass or vase. This item should not be used near water.

Non-Use Periods: Always unplug the AC adapters from the wall outlets during long periods of non-use. Ventilation: This baby monitor should not be used on a bed, sofa, rug or similar surface that may block the ventilation openings, or be placed in an

enclosed area, such as a bookcase or drawer that may impede air ﬂow. Keep Away from Sources of Heat: This unit should not be exposed to direct heat sources such as a candle, ﬁreplace, radiator, heat register, stove or other appliance that emits heat. The unit should not be left in direct sunlight.

Power Source: This unit should only be used with the AC power adapters included in this package (rated 5.9V 1A) Damage Requiring Service: This unit should be serviced by qualiﬁed personnel only when:

a. Objects have fallen or liquid has been spilled into the product b. The units have been exposed to rain c. The units do not appear to operate normally or exhibits a distinct change in performance d. The units have been dropped or the enclosure damaged

This product cannot replace responsible adult supervision.

Use only with provided power supply.

The socket-outlet shall be installed near the equipment and

shall be easily accessible.

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN

INCORRECT TYPE!

Dispose of used batteries according to the instructions.

Use only batteries/power supplies listed in the user manual.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inerference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.  Increase the separation between the equipment and the receiver.  Connect the equipment into an outlet dierent from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help.

IC STATEMENT / DÉCLARATION IC:

This Class B digital apparatus complies with ICES-003. / Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This device complies with Industry Canada licence-exempt RSS 210 standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR 210 d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Please visit our website at www.myLEVANA.com for information about your product’s warranty

We take quality very seriously. This is why all of our products come with a one-year warranty from the original purchase date against defects in workmanship and materials. If you have warranty or support issues please contact us using any of the following methods:

Web: www.mylevana.com Support: www.mylevana.com/support

LEVANA Canada LEVANA USA 4080 Montrose Road 60 Industrial Parkway #Z64 Niagara Falls, ON Cheektowaga NY Canada L2H 1J9 USA 14227

Warranty Terms

1. LEVANA® products are guaranteed for a period of one year from the date of purchase against defects in workmanship and materials. This warranty is limited to the repair, replacement or refund of the purchase price at LEVANA’s option.

2. This warranty becomes void if the product shows evidence of having been misused, mishandled or tampered with contrary to the applicable instruction manual.

3. Routine cleaning, normal cosmetic and mechanical wear and tear are not covered under the terms of this warranty.

4. The warranty expressly provided for herein is the sole warranty provided in connection with the product itself and no other warranty, expressed or implied is provided. LEVANA assumes no responsibilities for any other claims not speciﬁcally mentioned in this warranty.

5. This warranty does not cover the shipping cost, insurance or any other incidental charges.

6. You MUST contact LEVANA at www.mylevana.com/support before sending any product back for repair. You will be sent a Return Authorization form with return instructions. When returning the product for warranty service, please pack it carefully in the original box with all supplied accessories, and enclose your original receipt or copy, and a brief explanation of the problem (include RA #).

7. This warranty is valid only in Canada and the continental U.S.

8. This warranty cannot be re-issued.

TABLE OF CONTENTS

SAFETY INSTRUCTIONS .............................................................................................................................................................................................................................................2

FCC STATEMENT ..........................................................................................................................................................................................................................................................3

WARRANTY ...................................................................................................................................................................................................................................................................4

WHAT’S INCLUDED .....................................................................................................................................................................................................................................................6

BUTTONS AND CONNECTIONS - MONITOR ........................................................................................................................................................................................................ 7

BUTTONS AND CONNECTIONS - CAMERA ...........................................................................................................................................................................................................8

SETUP .............................................................................................................................................................................................................................................................................9

Battery installation .....................................................................................................................................................................................................................................9

Connecting Power to the Monitor / Charging Battery .....................................................................................................................................................................10

Connecting Power to the Camera .......................................................................................................................................................................................................10

Screen Icons ............................................................................................................................................................................................................................................. 11

OPERATION ................................................................................................................................................................................................................................................................12

Turn the Monitor ON / OFF ....................................................................................................................................................................................................................12

Pairing the Cameras & Monitor .............................................................................................................................................................................................................12

Placement of the Monitor ......................................................................................................................................................................................................................13

Placement of the Camera ......................................................................................................................................................................................................................13

Mounting the Camera on a Tabletop Safely .......................................................................................................................................................................................13

Mounting the Camera on a Wall Safely ...............................................................................................................................................................................................14

Night Vision ...............................................................................................................................................................................................................................................15

Adjusting the Camera Angle ..................................................................................................................................................................................................................15

Using the ZOOM Function .....................................................................................................................................................................................................................15

Volume .......................................................................................................................................................................................................................................................16

Using the Talk to Baby™ Two-Way Intercom .....................................................................................................................................................................................16

Selecting a Lullaby ................................................................................................................................................................................................................................... 17

Using Power Save ....................................................................................................................................................................................................................................17

Changing the Camera View ...................................................................................................................................................................................................................18

Setting the Brightness .............................................................................................................................................................................................................................18

Using PEEP Mode .....................................................................................................................................................................................................................................19

Contacting Customer Support ............................................................................................................................................................................................................. 20

TROUBLESHOOTING ................................................................................................................................................................................................................................................21

MAINTENANCE ..........................................................................................................................................................................................................................................................21

SPECIFICATIONS ........................................................................................................................................................................................................................................................22

WHAT’S INCLUDED

             

This product is not a toy. This product contains small parts. Exercise care when unpacking and assembling the product.

Battery life of 48 hours based on 10 audio activations while in power save (PEEP) mode. Battery lasts an average of 10 hours with continuous audio/video usage.

Night vision range up to 12ft under ideal conditions. Objects at or beyond this range may be partially or completely obscured, depending on the camera application. Optimum range is 200ft when signal is passing through walls or ﬂoors. Microwave ovens (when in use) may cause signal disruption at close range. Buildings with metal frames may also cause signal disruption. Maximum transmission range is 750 feet.

This product does not replace responsible adult supervision. Check on your child at regular intervals and make sure your monitor is always adequately charged.

Strangulation Hazard: Children can become entangled in cords. Power cords should be kept more than 3 feet away from the crib and baby’s reach at all times. Baby monitors/ cameras with power cords should never be hung on or near the crib.

We reserve the right to change models, conﬁguration, or speciﬁcations without notice or liability. Product may not be exactly as shown.

MONITOR

1. LOCK / UNLOCK BUTTON

Disables ALL function buttons in the LOCK position

2. LCD SCREEN

3. POWER & SCREEN ON/OFF

4. POWER INPUT

5. TALK TO BABY™

Press and hold to talk, release to listen

6. PAN & TILT BUTTON

7. MENU

8. MICROPHONE

9. COLOR-CHANGING LED RING

Changes color with sound intensity/battery charge

10. SELECTION / ZOOM BUTTON

11. DIRECTIONAL ARROWS / VOLUME CONTROL

12. ANTENNA

Extend to improve signal

13. TABLE STAND

14. SPEAKER

15. BATTERY COMPARTMENT

7 8

14 15

CAMERA

2 3

7 8

1. PTZ CAMERA

2. MICROPHONE

3. POWER LED

4. NIGHT VISION LIGHT SENSOR

5. ANTENNA

6. POWER INPUT

7. POWER ON/OFF

8. SPEAKER

SETUP

LET’S GET STARTED!

Battery Installation

1. Gently remove the BATTERY COMPARTMENT COVER on the back of the monitor by sliding down.

2. Insert the battery; the battery connectors on the battery should line up with the connectors inside the battery compartment.

3. Slide the BATTERY COMPARTMENT COVER back into place.

4. For extended periods of non-use, please remove battery from baby monitor.

Get the Most Out of Your Rechargeable Battery

Fully charge battery (4 hours) before ﬁrst use.

To maximize battery life, charge battery before

battery is fully drained.

Avoid extreme heat or cold as this will aect the life

of the battery.

side of the monitor ONCE.

enters standby/sleep mode.

will extend battery life.

Turn LCD screen OFF; press POWER button on the

PEEP Mode: After 45 seconds of inactivity, monitor

Adjustable Brightness: Decreasing screen brightness

SETUP

Connecting Power to the Monitor / Charging Battery

1. Connect the small end of power adapter marked MONITOR the monitor as shown in the diagram. Connect the other end of the adapter into an available wall outlet. For safety reasons, ONLY use the adapters included in the package.

2. Press and hold the POWER button on the side of the monitor to turn the monitor ON.

3. The icon in the top right corner of the main screen will show you the battery power status.

4. The LED Ring on the front of the monitor also indicates the battery power status.

SOLID BLUE = BATTERY FULLY CHARGED SLOW FLASHING BLUE = BATTERY CHARGING QUICK FLASHING BLUE = BATTERY LOW FLASHING PINK = PAIRING UNSUCCESSFUL

EMPTY CHARGING FULL

Connecting Power to the Camera

1. Take the second power adapter and connect the small end of the power adapter marked CAMERA into the DC input on the side of the camera base as shown in the diagram. For safety reasons, ONLY use the adapters included in the package.

Note: Baby monitors and cameras with power cords should never be hung on or near the crib as it is a strangulation hazard. Power cords should be kept no less than 3 feet away from the crib and the baby’s reach at all times.

into the DC input on the side of

LED Ring

ON / OFF

DC Input

Power

DC Input

Switch

SCREEN ICONS

SIGNAL STRENGTH

NO STRONG

SIGNAL SIGNAL

BATTERY STRENGTH

EMPTY CHARGING FULL

POWER SAVE

OFF ON

LULLABIES

CAMERA



1 2 3 4 MODE

PTZ / VPIZ / PTZ

ZOOM

TALK TO BABY™

SUPPORT

PEEP MODE

OFF LOW MEDIUM HIGH

VOLUME

OFF LOUD

BRIGHTNESS

DARK BRIGHT

PAIRING

PAIRING CAM CAM CAM CAM 1 2 3 4

OPERATION

Turn the MONITOR ON/OFF

• Press and hold the POWER button on the side of the monitor to turn the monitor ON.

• Press and hold the POWER button again to turn OFF the monitor.

Pairing the Camera(s) and Monitor

The camera and monitor come paired (connected) to each other automatically. However, if upon opening this package the devices do not automatically connect and transmit, you may do so manually. To pair additional cameras, repeat steps 1 to 3 and be sure to assign a dierent camera number to each additional camera.

Note: Before you begin pairing, be sure to have the monitor and the camera(s) side by side.

1. To pair your camera and monitor, press the MENU the navigational arrows PAIRING icon and press the SELECT + button once to select.

2. Use the navigational arrows

3. Press the SELECT + button. When you see ﬂashing next to camera

icon, quickly press and hold the PAIRING button on the BOTTOM of the camera. A checkmark pairing is successful. Video/audio will be transmitted automatically.

on the front of the monitor, highlight the

to highlight the the icon.

will appear next to camera conﬁrming

Note: Repeat steps above when pairing additional cameras.

button. Using

CAMERA

BOTTOM

OPERATION

Placement of the Monitor

This monitor can be placed on a tabletop.

 You can place the monitor on a tabletop by using the retractable table stand on the back of the

monitor. When not in use, simply tuck the table stand away into the back of the monitor until you hear a "click".

Placement of the Camera

This camera can be placed on a tabletop or hung on the wall above the area being monitored.

 Place the camera within 15 feet of the area being monitored for best picture results.  Do not place objects within 2 feet of the ﬁeld of vision of the camera as the night vision will not activate correctly if objects

are too close.

Mounting the Camera on a Tabletop Safely:

1. Place the camera on a tabletop no less than 3 feet away from your baby’s crib.

2. Feed the power cord down the back of the table or use wall clips (not included) to secure the cord away so the baby cannot reach it.

3. Plug in the power cord, check the monitor to ensure that you are getting a good view of your child and there are no obstructions.

3 ft

OPERATION

Mounting the Camera on a Wall Safely:

Before drilling the holes, it is important to check the reception and camera positioning in the intended location on the wall. Ensure you are hanging the camera no less than 3 feet away from baby’s crib.

1. Pre-drill two holes in the wall using a 3/16”, 4.8mm drill bit.

2. Insert wall anchors (not included) into each hole and tap gently with a hammer until the anchor is ﬂush with the wall.

3. Insert a screw (not included) into each wall anchor and tighten until the screws only stick out about a 1/2 inch.

4. Plug the power cord into the power input of the camera.

5. Locate the wall mounting holes on the bottom of the camera base.

6. Slide the holes over the screws sticking out of the wall.

7. Conﬁrm that the camera is secure, if it is loose you may have to tighten the screws more.

8. Use wall clips (not included) to secure the power cord away from the crib or the baby’s reach.

9. Connect the other end of the adapter into an available wall outlet.

OPERATION

Night Vision

The camera is equipped with NEW Invisible IR (infrared) LEDs which keep the nursery dark. The LEDs are located on the front of the camera and allow you to see up to 12 feet in complete darkness so you can check on your baby at any time of night. The night vision LEDs will activate automatically when the Light Sensor on the side of the camera detects that the light levels are too low.

Adjusting the Camera Angle - PTZ

The camera is equipped with Pan / Tilt / Zoom (PTZ). You can adjust the angle 300° degrees horizontal and 110° degrees vertical from the center position.

Using the ZOOM Function

INVISIBLE

LEDs

CENTER POSITION

Zoom in/out

OPERATION

Volume

Use the navigational arrows to increase /decrease /mute the VOLUME.

VOLUME

Decrease / Increase

Using the Talk to Baby™ Two-Way Intercom

With the simple press of a button you can talk to your child at any time without entering the nursery.

1. To talk, press and hold the

2. To talk when using multiple cameras, select the camera in the MENU and press the

button on the front of the monitor and release to listen.

(MUTE)

Note: Placing the monitor and camera too close together will create feedback. DECREASE or MUTE the volume and move the camera away from the monitor.

button, release to listen.

Note: To optimize the eectiveness of the PTT (Press to Talk) function, please hold the monitor at least 6-8 inches away from your face .

OPERATION

Setting a lullaby

Choose from three dierent lullabies to soothe your baby to sleep.

1. To select a lullaby, press the MENU the front of the monitor, highlight the LULLABY icon.

2. Use the to toggle to select the LULLABY icon of your choice and press the SELECT

button once to select.

3. To turn OFF the lullabies, select the and press the + button once to select.

Using Power Save

When Power Save is ON, the monitor enters standby/sleep mode after 1 minute of inactivity but keeps the audio on. When sound is detected, the screen changes to live view.

 To access live view manually when the screen is o, press the POWER button ONCE.

1. To set Power Save, press the MENU on the front of the monitor, highlight the POWER SAVE icon .

2. Press the SELECT + button once to select.

3. To return to continuous live view, press the MENU

button. Using the navigational arrows on

button. Using the navigational arrows

button.

OPERATION

Changing the Camera View

1. To change the camera view, press the MENU

arrows

2. Use the to toggle to select the CAMERA icon of your choice and press the

SELECT + button once to select.

on the front of the monitor, highlight the CAMERA icon.

button. Using the navigational

3. Select

once to select.

4. To return to continuous live view, press the MENU

Setting the Brightness

Brightness Mode sets the brightness of the the screen. Brightness Mode also extends

the battery life.

1. To set the Brightness Mode, press the MENU

arrows

2. Use the to toggle to your desired brightness and press the SELECT + button

once to select.

to cycle through cameras 1 through 4 and press the SELECT + button

button.

button. Using the navigational

on the front of the monitor, highlight the BRIGHTNESS icon.

OPERATION

Using PEEP Mode

When in PEEP Mode, the monitor enters standby/sleep mode after 1 minute of inactivity. When sound is detected, the screen changes to live view.  To access live view manually when the screen is o, press the POWER button

ONCE.

• PEEP Mode extends the battery life over 48 hours.

1. To set PEEP Mode, press the MENU the front of the monitor, highlight the selected PEEP Mode icon.

2. Use the to toggle to the desired PEEP Mode icon and press the SELECT + button once to select.

3. To return to continuous live view, press the MENU

The LED Ring on the front of the monitor also indicates the level of the sound in the room is with colors.

SOUND SENSITIVITY COLORS

DISCON. / WHISPER / MURMUR / COOING / CHATTER / YELLING

button. Using the navigational arrows on

button.

LED Ring

OPERATION

Contacting Customer Support

Customer Support is just a click away whenever you need it! Our customer support team

can be reached by live web chat or on our website at www.mylevana.com/support. Our experts will be happy to assist you in English, French and Spanish.

OPERATION

1. To access Customer Support, press the MENU arrows

SELECT + button once to select.

2. This will take you to the screen which displays our Customer Support information. Press the MENU

on the front of the monitor, highlight the SUPPORT icon press the

button once to EXIT the Customer Support screen.

button. Using the navigational

Support: www.mylevana.com/support Web: www.mylevana.com Online Live Web Chat: www.mylevana.com

TROUBLESHOOTING

ISSUE POSSIBLE SOLUTION

Equipment does not function  Conﬁrm that the camera and monitor are ON

 The battery may be depleted; charge battery  The power adapters may not be properly connected

No reception  Camera and monitor may not be properly paired; follow PAIRING instructions

 Camera may be too far away from the monitor  Extend the antenna on the monitor

Reception Interference (static)  The camera and monitor may be too far apart

 The battery power may be too low  Other electronic devices may be interfering with the signal  The camera or monitor may be placed too close to many metal objects

Feedback (screeching, static)  The camera and monitor may be too close together

 The volume on the monitor may be set too high

Noise (static, beeping)  Battery power may be too low

The buttons are not working  LOCK/UNLOCK Button is in LOCKED position; move to UNLOCK position

Picture works but there is no sound  Volume setting may be too low Picture is black and white  Night vision LEDs may be ON; increase the amount of light in the room being monitored Day/night vision is whitewashed  Ensure that night vision light sensor is pointed away from a wall and is not covered. The rechargeable battery will

not charge

Maintenance

 Clean the surfaces of the camera and monitor with a soft, ﬂu-free cloth  If the units become dirty, use a lightly damp cloth to wipe surfaces, taking care to not allow water into any openings  Never use cleaning agents or solvents

 The power adapters may not be connected  Battery pack may not be properly connected inside the battery compartment

+ 48 hidden pages

Levana Astra PTZ User Manual [en, es, fr]

Specifications and Main Features

Frequently Asked Questions

User Manual