Leuze GSU 710/66 Data Sheet

IP 40

IEC 68...

IEC 801...

GSU 710/66 Double Sheet Testing Unit

Dimensioned drawing

en 05-2014/06 50108368-01

 Reliable detection of multi-layer paper and

plastic sheets and metal foils

 Measurement range from 20g/m2 paper to

800g/m

2

cardboard

 Plug connection
 Operating state indicators via light-emitting

diodes

 Push-pull switching outputs

Accessories:

(available separately)

 M12 connectors (KD …)
 Ready-made cables (K-D …)

A Through hole
B Minimum intrusion depth of sheet edge
C Inlay nut M4 possible
D Red indicator diode
E Yellow indicator diode

Electrical connection

We reserve the right to make changes • DS_GSU71066_en_50108368_01.fm

Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. [phone]

• www.leuze.com

GSU 710/66 - 05

GSU 710/66

Specifications

Physical data

Mouth width 13mm
Mouth depth 89mm
Minimum intrusion depth 31mm
Converter frequency approx. 330kHz

Timing

Switching frequency 200Hz
Response time 5ms
Delay before start-up ≤ 300ms acc. to IEC 60947-5-2

Electrical data

Operating voltage UB 18 … 30VDC (incl. residual ripple)
Residual ripple ≤ 15% of U
Open-circuit current ≤ 50mA
Switching outputs 2 push-pull switching outputs
Function characteristics single sheet detected, or ≥ 1 sheet

Signal voltage high/low ≥ (U
Output current max. 100mA per output

double sheet detected, or ≥ 2 sheets

Indicators

Yellow LED single sheet detected
Red LED double sheet detected

Mechanical data

Housing plastic
Color red
Weight approx. 100g
Connection type M12 connector, 5-pin, or

cable 400mm with M 12 connector, 5-pin

Environmental data

Ambient temp. (operation/storage) 0°C … +50°C/-40°C … +70 °C
Protective circuit
VDE safety class II, all-insulated
Protection class IP 40
Standards applied IEC 60947-5-2

2)

1, 2, 3

Options

Teach-in input

Teach-in input resistance R
Teach-in active/not active …/…P (PNP): ≥ 10V/≤ 2 V or floating
Teach-in duration max. 100ms
Teach-in delay approx. 300 ms

1) Function: …/…P = active high (+24V); not active low (0V)
The push-pull switching outputs must not be connected in parallel

2) 1=transient protection, 2=polarity reversal protection, 3=short circuit protection for all outputs

: 10kΩ

in

-2V)/≤ 2V

B

B

1)

Mode of operation

The "singlesheet" output sig­nals that an object is within
the detection range. This out­put may be used to check for
presence.

A detected double sheet is
signaled at the "double
sheet" output.

In the standard mode, 2-layer
paper sheets with weights
between approx. 40g/m²
and approx. 400g/m² are
detected without additional
calibration.

With the "teach-in", the
measurement range limits
can be expanded to between
approx. 20g/m² and approx.
800g/m².

The calibration process is
started by applying a high
signal at the "teach-in" input.

Calibration is performed
either directly on a medium ­if a sheet is in the detection
range at the calibration time ­or calibration is performed
automatically if a medium is
inserted into the detection
range after the calibration
time.

The calibration process is
concluded after approx.
100ms.

When switched back on, the
sensor again functions in
standard mode

2

40g/m

…400g/m2.

Order guide

Designation Part No.

M12 connector GSU 710/66.4P-S12 50108702

400mm cable with M12 connector GSU 710/66.4P, 400-S12 50112912

Remarks

 Intended use:

The GSU 710 double sheet
testing unit is a monitoring
unit predominately designed
for single sheet checking in
paper processing machines.

Operate in accordance with
intended use!

 This product is not a safety sensor

and is not intended as personnel
protection.

 The product may only be put into

operation by competent persons.

 Only use the product in accor-

dance with the intended use.

GSU 710/66 - 05 2014/06