LetsGoAero GearCage Ramp, H00680 Product Manual
GearCage® Ramp
Accessory Ramp Kit for GearCage Cargo Carriers
PRODUCT MANUAL
ASSEMBLY, INSTALLATION, AND OPERATION INSTRUCTIONS
Part No. H00680
Installation & Safe Use Operation Highlights
Fits GearCage Model Cargo Carriers (Sold Separately)
Rated for 300 lbs of cargo payload.
For More Information & Accessories, Visit our Website - www.LetsGoAero.com
For Technical Support & Product Questions Contact Us at 877-464-2376 or 719- 630-3800
GC RAMP 110117
Email: SUPPORT@LETSGOAERO.COM
Copyright© 2017, Lets Go Aero, Inc., All rights reserved.
PAGE 1 OF 9
PARTS LIST
27” CROSS TUBE
4
A
48” SIDE TUBE
2
B
PIN NUT
8
C
M6 x 65 BUTTONHEAD BOLT
8
D
M6 FLAT WASHERS
28
E
TRANSITION FLAP
1
F
FLOOR PANELS
3
G
M6 x 40 BUTTONHEAD BOLT
12
H
M6 NYLOCK NUT
16
J
HINGE
2
K
M8 x 40 BUTTOHEAD BOLT
2
L
M8 WASHER
8
M
M8 NYLOCK NUT
4
N
M6 x 16 BUTTONHEAD BOLT
6
P
LATCH KEEPER
2
Q
M8 x 70 BUTTONHEAD BOLT
2
R
M6 WASHER
14
S
TOOLS NEEDED:
4mm ALLEN WRENCH
5mm ALLEN WRENCH
3/16 ALLEN WRENCH
5/32 ALLEN WRENCH
PAGE 2 OF 9
FLAT HEAD SCREWDRIVER
10mm SOCKET or WRENCH
13mm SOCKET or WRENCH
1/2in SOCKET or WRENCH
FOR INFO & VIDEOS
ON GEARCAGE
CARRIERS &
ACCESSORIES
STEP 1
Lay out the two (2) Side Tubes [B] and
four (4) Cross Tubes [A] as shown
[Figure 1].
NOTE: Each Cross Tube [A] end should
align with the holes located on the sides
of the Side Tubes [B].
NOTE: The Pull Latches located along
the Side Tubes [B] should be parallel
with the bent ends of the steel pulls
facing the interior of the assembly.
STEP 2
Insert one (1) Pin Nut [C] at each end
of Cross Tubes [A] through the holes
located on the side of the tube as shown
[Figure 2].
TOOL(S): 4mm ALLEN WRENCH & FLAT HEAD SCREWDRIVER
[Figure 1]
D
B
B
[Figure 4]
A
A
Pull Latches
[Figure 2]
NOTE: The “slot end” illustrates the Pin
Nuts’ [C] internal thread direction [Figure
3].
NOTE: The “notched end” of the Pin Nut
should lock into the edge of the Cross
Tube [A] hole as shown [Figure 4].
Secure the Side Tubes [B] to the Cross
Tubes [A] by threading one (1) M6 x
65 Button Head Bolt [D] with a M6 Flat
Washer [E] through the Side Tubes and
into each Pin Nut [Figure 4].
C
C
STEP 3
Lay the Transition Flap [F] onto the end of the ramp assembly aligning the
mounting holes [Figure 5].
NOTE: The Transition Flap [F] should be placed on the Cross Tube [A]
located furthest away from the Side Tubes [A] Pull Latches with the
Transition Flap pointing away from the assembly.
E
[Figure 5]
F
D
B
B
A
C
NOTCH
END
SLOT
END
[Figure 3]
NOTE: Installation of the Transition Flap [F] is optional, and can be
removed for fold at storage t on the GearCage carrier oor of Let’s Go
Aero 4ft models.
Pull Latches
A
PAGE 3 OF 9
Loading...