Page 1
HEARTH PRODUCTS
KITS AND ACCESSORIES
P/N 506033-33
Rev. NC, 03/2010
INSTALLATION INSTRUCTIONS FOR INSTALLING FACEPLATE KITS
FOR USE WITH MODELS S160, SS210, ST210, S260, ST310, C160, C210,
C260, E260 AND C310 WOOD STOVES AND WOOD FIREPLACE INSERTS
KIT CONTENTS
1 ea. Arch or Traditional Faceplate (item #4)
1 ea. Spring Handle (item #5)
1 ea. Tube Of Anti-seize (item #6)
2 ea. #6 x 1” Carriage Bolt (item #1)
2 ea. #6 Nut (item #2)
1 ea. Lennox Nameplate - Gold (item #3)
1 ea. Country Nameplate - Gold (item #3)
1 ea. Instruction Sheet
TOOLS NEEDED
5/32” Allen Wrench or T-Handle Wrench
Open End Wrench - 5/16”
Faceplate Kit (Includes Faceplate, Handle and Nameplate)
Cat. No. Model Description
H7903 TRAD-FPK-BG-LG Traditional Faceplate Kit, Brushed Gold
H7906 TRAD-FPK-G-LG Traditional Faceplate Kit, Gold
GENERAL INFORMATION
These decorative faceplate kits are offered in various attractive finishes to
accentuate the look of your wood stove or wood fireplace insert.
Take great care when handling the faceplates to prevent scratching.
FACEPLATE KITS
For Models: C260, E260, C310, S260 and ST310
3
4
Arch Faceplate
Traditional Faceplate
4
6
5
2
Figure 1 - Kit Contents
Faceplate Kits (Includes Faceplate, Handle and Nameplate)
For Models: C160, C210, S160, ST210 and SS210
Cat. No. Model Description
H7901
H7902 TRAD-FPK-BG-SM Traditional Faceplate/Brushed Gold
H7904 ARCH-FPK-G Arch Faceplate/Gold
H7905 TRAD-FPK-G-SM Traditional Faceplate/Gold
ARCH-FPK-BG Arch Faceplate/Brushed Gold
NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE.
If you encounter any problems, need clarification of these instructions
or are not qualified to properly install this kit, contact you local distributor or dealer.
Read this instruction sheet in its entirety before beginning the installation.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO
THESE INSTRUCTIONS.
ALLOW THE STOVE OR INSERT TO COMPLETELY COOL BEFORE PROCEEDING.
1
IMPORTANT
Be sure to clean plated surfaces with a soft cloth
and household glass cleaner prior to burning the
stove or insert. Fingerprints left on the plated
surfaces while burning may remain on the finish
permanently.
1
Page 2
INSTALLATION INSTRUCTIONS
Step 1. Remove Spring Handle - Twist spring handle clockwise and pull
down at the same time to remove from handle rod (see Figures
2 and 3).
Spring Handle
Figure 2
Rotate spring handle
clockwise to remove
Allen head screws
indicated by arrows
Figure 4
Allen Head Screw
and Washer
Figure 3
Step 2. Remove Faceplate Screws and Washers - Partially peel back the
door gasket, to expose the six screws and washers (see Figure
4). Note: Peel the gasket back just enough to get your 5/32” allen
wrench on the screws (see Figure 5). It is very important not to
pull the gasket all the way off the door. If the gasket becomes
hard to pull, you have gone too far. Fragile care should be taken
when working around the door rope junction.
IMPORTANT NOTE: Be sure not to over tighten the screws. If the screws
are over tightened the glass may crack when the stove is hot.
Allen Wrench
Figure 5
Step 3. Remove Faceplate - Be advised that the faceplate also functions as
a glass retainer (see Figure 6). Make sure to apply inward pres-
sure on the glass while removing the faceplate. IMPORTANT,
PRESS THE GLASS INWARD TO ENSURE THE GLASS STAYS
IN THE GROOVE AND DOES NOT FALL OUT AND BREAK.
Faceplate
Figure 6
2
NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE.
Page 3
Step 4. Install New Faceplate - Slide the faceplate over the handle rod
while the handle rod is at a 90° position (see Figures 7 and 8).
Move the handle rod up and down and slightly in and out when
sliding the faceplate onto the handle rod.
.25 IMPORTANT, ALWAYS PRESS INWARD ON THE GLASS WHILE
THE FACEPLATE IS NOT RETAINING THE GLASS, OTHERWISE
THE GLASS MAY FALL OUT AND BREAK.
Door Rope
Screws and
Washers
Door Back
Handle Rod
Glass
Glass Gasket
Figure 7
Figure 8
Step 5. Reinstall The Six Screws and Washers - Apply the anti-seize
provided before reinstalling the screws. The anti-seize is applied
to the screws for ease of the removal of the screws if removal is
needed in the future. Ensure that the widest side of the washers
is in the direction of the glass as shown in Figure 9. Do not
tighten screws completely at this time. The door will have up and
down play. Place a level on top of the door to level the faceplate.
Once the faceplate is level, tighten the six screws. The washers
should have a slight bow once they are tightened.
Faceplate
Figure 9
Step 6. Reinstall Spring Handle - Slide the spring handle over the handle
rod by pushing up and turning the spring handle clockwise (see
Figure 10). Make sure to leave a 1/2 inch gap between the end
of the handle rod and the bottom of the spring handle, This will
also allow for a 1/2 inch of play side to side. Installing the spring
handle too far, where there is no side to side play, will result
in the spring handle becoming VERY HOT to the touch.
1/2”
Figure 10
NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE.
3
Page 4
NAMEPLATE OPTIONS
This instruction sheet explains how to install a nameplate onto a woodburning stove or insert. Your new Country Collection™ wood-burning
appliance includes a nickel Country nameplate in the manual packet and
a nickel Lennox™ nameplate installed on the appliance.
REPLACEMENT KIT CONTENTS (See Figure 12)
The contents below ship separately with Cat. # H8079 and H8080
1 ea. Instruction Sheet
2 ea. #6 x 1” Carriage Bolt (item #1)
2 ea. #6 Nut (item #2)
1 ea. Nameplate - Lennox (Gold or Nickel, item #3)
1 ea. Nameplate - Country (Gold or Nickel, item #3)
Cat. # Description
H8079 Nameplate Kit with Hardware - Nickel
H8080 Nameplate Kit with Hardware - Gold
TOOLS NEEDED
Open End Wrench - 5/16”
Smoke Hood
Figure 11
1
3
INSTALLATION INSTRUCTIONS
Step 7. Align nameplate on the center of the smoke hood.
Step 8. Insert carriage bolts through nameplate and smoke hood.
Step 9. Open the firebox door to allow access to the underside of the
smoke hood and secure the carriage bolts using the #6 nuts.
REMOVAL INSTRUCTIONS
Remove the nameplate in the reverse order of installation.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
2
2 ea. #6 x 1” Carriage Bolt (item #1)
2 ea. #6 Nut (item #2)
1 ea. Nameplate - Lennox (Gold or Nickel, item #3)
1 ea. Nameplate - Country (Gold or Nickel, item #3)
Figure 12
Lennox Hearth Products reserves the right to make changes at any time, without notice, in
design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2010 Lennox Hearth Products
P/N 506033-33 Rev. NC 03/2010
4
1110 West Taft Avenue • Orange, CA 92865
Loading...