Lennox Hearth ADAGIO-pF, ADAGIO-AG User Manual

HEARTH PRODUCTS

KITS AND ACCESSORIES

750,231M REV. NC 06/2008

INSTALLATION INSTRUCTIONS FOR FACADE KITS FOR USE WITH ADAGIO™ DIRECT-VENT GAS FIREPLACES

KIT CONTENTS:

Facade Kit

1 ea. Facade Assembly (1) 1 ea. Instruction Sheet

Filigree Inset Kit

1 ea. Upper Filigree inset (2) 1 ea. Lower Filigree inset (3) 7 ea. Washers #10 (4) 7 ea. Hex Head Nuts (5)

7 Places

Cat. No Model Description

H5773 ADAGIO-AG Arched Face Black Facade H5774 ADAGIO-PF Arched Face Brushed Nickel Facade

Installer: Leave This Instruction Sheet With The Appliance.

Consumer: Retain This Instruction Sheet For Future Reference.

The arched facade kits require a ﬁligree inset kit. These kits are sold separately. Contact your dealer for ordering information.

Filigree Inset Kits (Sold Separately - Required)

Cat. No. Model Description

H6845 ADAGIO-INSET-ASPEN-BK Aspen, Black

H6846 ADAGIO-INSET-ASPEN-BN Aspen, Brushed Nickel

H6847 ADAGIO-INSET-ASPEN-BKN Aspen, Black Nickel

H6848 ADAGIO-INSET-ASPEN-G Aspen, Gold

H6849 ADAGIO-INSET-NAPA-BK Napa, Black

H6850 ADAGIO-INSET-NAPA-BN Napa, Brushed Nickel

H6851 ADAGIO-INSET-NAPA-BKN Napa, Black Nickel

H6852 ADAGIO-INSET-NAPA-G Napa, Gold

H6853 ADAGIO-INSET-TUSCAN-BK Tuscan, Black

H6854 ADAGIO-INSET-TUSCAN-BN Tuscan, Brushed Nickel

H6855 ADAGIO-INSET-TUSCAN-BKN Tuscan, Black Nickel

H6856 ADAGIO-INSET-TUSCAN-G Tuscan, Gold

Figure 1

TOOLS / SUPPLIES NEEDED:

3/8” Socket or Nutdriver

GENERAL INFORMATION

The arched facade kits are offered in two attractive ﬁnishes, black and brushed nickel. If you encounter any problems or need clariﬁcation of these instructions, contact you local distributor or dealer.

Note: The base of the appliance will need to be elevated by 3/4" minimum above the ﬂoor to allow for the proper ﬁt of the facade (i.e. 3/4" board as platform). See Installation Instructions Manual.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

INSTALL ONLY WHEN FIREPLACE IS OFF AND COOL.

ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS PROVIDED IN THE INSTALLATION INSTRUCTIONS MANUAL AND THE CARE AND OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO THESE INSTRUCTIONS. THOROUGHLY READ AND FOLLOW THE INSTRUCTIONS PROVIDED WITH THE APPLIANCE BEFORE PROCEEDING TO THE FOLLOWING INSTRUCTIONS.

INSTALLATION INSTRUCTIONS

1. Install the appliance, ﬁrebox liner and logs per the Installation Instructions Manual provided with the appliance and the Installation Instruction Sheet provided with the ﬁrebox liner kit (sold separately).

2. Using a 3/8” socket or nutdriver, remove heat shield, screen retainer and screen from facade. See Figure 2.

3. Using a 3/8” socket or nutdriver, install the upper ﬁligree inset, lower ﬁligree inset, screen and screen retainer with provided washers and nuts as shown in Figure 2. Note: you will have four extra washers

and nuts.

4. Reinstall heat shield aligning the top corners of the heat shield with the etch marks in the back of the facade for proper placement. Do not over tighten nuts.

Etch

Marks

Figure 4 for instructions on accessing the control compart-

6. See ment.

Control Compartment Panel

Upper Filigree

Heat Shield

Lower Filigree

Screen

Screen Retainer

Figure 2

5. Install the facade onto the ﬁreplace face per instructions in Figure 3.

Facade

Align the tabs on the bracket assemblies all the way into the slots on ﬁreplace, then push facade down to ensure engagement.

Facade

Control Compartment

Magnets

To access the control compartment, pull the hinged door forward and up as shown. To close, hinge the door closed until magnets secure it in place.

Figure 4 - Opening the Control Compartment Panel

Brushed Nickel Facade Shown

Slots on Fireplace

(2 places each side)

Note: There are two mounting positions on the facade hanging brackets to better accommodate a range of facing thicknesses. Adjust to the notch on the hanging bracket that works best for your installation.

Tabs on Bracket Assemblies (2 places each side)

Figure 3 - Install Facade

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, speciﬁcations, prices and the discontinuance of colors, styles and products. Consult your local distributor for ﬁreplace / insert code information.

P/N 750,231M REV. NC 06/2008

Figure 5 - Completed Installation

IMPORTANT NOTE (Gold and Nickel Finishes Only): The gold and nickel ﬁnishes will require heat to harden and cure (after approximately 3 ﬁres, the ﬁnish will be completely cured). Prior to burning this appliance the gold and nickel surfaces should be cleaned thoroughly with a good window cleaning solution and a soft cloth. Do not use any metal polishes or abrasives to clean the surfaces. Any oils or ﬁngerprints left on the ﬁnish during the curing process may become permanent blemishes.

Lennox Hearth Products 1110 West Taft Avenue • Orange, CA 92865