Lennox ADK40CPB, ADK40CBS, ADK45CBS, ADK45CPB, ADK24CPB User Manual

...

LENNOX HEARTH PRODUCTS

KITS AND ACCESSORIES

P/N 750,021M REV. E 03/2008

ARCH DOOR KITS WITH BRASS OR

BRUSHED STAINLESS STEEL TRIM

INSTALLATION INSTRUCTIONS FOR ARCH DOOR KITS WITH BRASS OR BRUSHED STAINLESS STEEL TRIM

FOR USE WITH MERIT™, MERIT PLUS™, OR ELITE

KIT CONTENTS: TOOLS REQUIRED:

1 ea. Arched Door 1 ea. Instruction Sheet

GENERAL INFORMATION

These arch door kits may be used with gas ﬁreplace models listed in Tables 1 & 2.

CAUTION

INSTALL ONLY WHEN THE FIREPLACE IS OFF AND COLD!

INSTALLATION INSTRUCTIONS

Part A: Elite Series Fireplaces

Step 1.

Slightly lift and pull the existing top radiant panel/hood assembly

away from the ﬁreplace, or pull hood and slightly lift and pull the existing louver assembly away from the ﬁreplace.

Step 2. Lift and pull the existing top and bottom bustle away from the

ﬁreplace.

Step 3. Open the bottom compartment door (either a radiant panel or

louver assembly) by pushing in simultaneously the left and right top corners of the door (the door is hinged at the bottom).

Step 4. Remove the bottom compartment door by sliding the hinge pin,

located at the door’s left side, to the right until it disengages from the left corner post hole. Pull the door diagonally to the left, away from the ﬁreplace.

Step 5. Remove the modesty panel as follows: lift the modesty panel by the

tab on the panel’s right end, pull the right end of the panel away from cabinet and then pull the panel diagonally out of the corner post slots on the left side of the unit. Remove the modesty panel carefully, so that none of the wires become loose or disconnected.

Arched Door

Glass Frame

Figure 1

None

Corner Tabs- At The Four Corners

Step 6. Open the glass door latche(s) located underneath the ﬁrebox.

Step 7.

Step 8. Center the arch door over the glass frame as shown in Figure 1.

CAT. NO. MODEL WHERE USED

81L34 ADK35CPB EDV3530, ED3530

81L35 ADK40CPB EDV4035, ED4035-2, LMDV-4035,

81L36 ADK45CPB EDV4540, ED4540-2, MPD4540

81L37 ADK24CPB EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL,

98L05 ADK33CPB MDR3328, MDT3328, MPDT3328,

26M43 ADK35CMPB MPD3530, MPD35ST, MPD35PF, MPB35ST,

H7026 ADK22CMPB MPD35PF

Table 1 - Arch Door Kit with Brass Trim

CAT. NO. MODEL WHERE USED

98L68 ADK35CBS EDV3530, ED3530

98L69 ADK40CBS EDV4035, ED4035-2, LMDV-4035,

98L70 ADK45CBS EDV4540, ED4540-2, MPD4540

98L71 ADK24CBS EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL,

98L62 ADK33CBS MDR3328, MDT3328, MPDT3328,

26M44 ADK35CMBS MPD3530, MPD35ST, MPD35PF, MPB35ST,

H7027 ADK22CMBS MPD35PF

Table 2 - Arch Door Kit with Brushed Stainless Steel Trim

SERIES GAS FIREPLACES

Remove the door from the ﬁreplace by swinging the bottom of

the door outward and lifting it up and away.

Press the arch door onto the glass frame and bend the four corner tabs into the frame’s U-channel as shown in Figure 2.

SSDV-4035, MPD4035, EDVST, EDST-2, EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL, EDCL-2, EBST-2, EBVPF, EBPF-2, EBVCR, EBCR-2, EBVCL, EBCL-2

EDCL-2, EBVPF, EBPF-2, EBVCR, EBCR-2, EBVCL, EBCL-2

MPDR3328, LMDVR-3328

LMDV-3530, SSDV-3530

SSDV-4035, MPD4035, EDVST, EDST-2, EDVPF, EDPF-2, EDVCR, EDCR-2, EDVCL, EDCL-2, EBST-2, EBVPF, EBPF-2, EBVCR, EBCR-2, EBVCL, EBCL-2

EDCL-2, EBVPF, EBPF-2, EBVCR, EBCR-2, EBVCL, EBCL-2

MPDR3328, LMDVT-3328, LMDVR-3328

LMDV-3530, SSDV-3530

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Bend The Arch Tab 90 Degrees Into The Glass Frame U-channel

Inside Top Corner View of Glass and Arch

Figure 2

Glass Frame U-Channel

Step 9. Position the glass door and arch assembly in front of the ﬁre-

box opening with the bottom of the door held away from the ﬁreplace. Hook the top ﬂange of the door frame over the top of the ﬁrebox frame. Let the bottom of the door frame swing gently in towards the ﬁreplace ensuring that the gasket seats evenly as the door frame draws shut. Fasten the two latches located underneath the ﬁrebox ﬂoor to the door’s vee-ﬂange. Close both the latches securely.

Step 13. Reinstall the top radiant panel/hood assembly, or hood and lou-

ver assembly. Make certain that the hood is installed as shown in Figure 3 (clean face models) or Figure 4 (louvered models). The ﬁreplace must not be operated without the hood installed as shown in these ﬁgures.

Note - Do not reinstall the top and bottom bustle with this arch door kit

installation. Keep them for any possible future re-decorating.

Part B - Merit, Merit Plus & SSDV Series Fireplaces

Step 1. Slightly lift and pull the existing top radiant panel/hood assembly

away from the ﬁreplace, or pull hood and slightly lift and pull the existing louver assembly away from the ﬁreplace.

Step 2. Open the bottom compartment door (either a radiant panel or

louver assembly) by pushing in simultaneously the left and right top corners of the door. (The door is hinged at the bottom.)

Step 10. Reinstall the modesty panel.

Step 11. Reinstall the bottom compartment door.

Step 12. Close the bottom radiant panel or louver assembly.

Top of Appliance

Top Radiant Panel

Top of Door Frame

Hood must be installed as shown.

Figure 3 - Clean Face

Top of Appliance

Louver Assembly

Top of Door Frame

Hood must be installed as shown.

Figure 4 - Louvered Face

Step 3. Open the two glass door latches located underneath the ﬁrebox.

Step 4. Remove the door from the ﬁreplace by swinging the bottom of

the door outward and lifting it up and away.

Step 5. Center the arch door over the glass frame as shown in Figure 1.

Press the arch door onto the glass frame and bend the four corner tabs into the frame’s U-channel as shown in Figure 2.

Step 6. Position the glass door and arch assembly in front of the ﬁrebox

opening with the bottom of the door held away from the ﬁreplace. Hook the top ﬂange of the door frame over the top of the ﬁrebox frame. Let the bottom of the door frame swing gently in towards the ﬁreplace ensuring that the gasket seats evenly as the door frame draws shut. Fasten the two latches located underneath the ﬁrebox ﬂoor to the door’s vee-ﬂange. Close both the latches securely.

Step 7. Reinstall the top radiant panel/hood assembly or hood and louver

assembly. Make certain that the hood is installed as shown in Figure 3 (clean face models) or Figure 4 (louvered models). The ﬁreplace must not be operated without the hood installed as shown in these ﬁgures.

Step 8. Close the bottom radiant panel or louver assembly.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, speciﬁcations, prices and the discontinuance of colors, styles and products. Consult your local distributor for ﬁreplace code information.

P/N 750,021M REV. E 03/2008

1110 West Taft Avenue • Orange, CA 92865