Lencore Spectra i.Net: G41 User Manual

SPECTRA – i.Net

PRODUCT SHEET & SPECIFICATIONS

IR TOUCH PAD
CONTROLLER

®

Model

G41

FUNCTION

The Spectra i.Net® IR Touch Pad Controller provides wall access
and immediate adjustments for the Spectra i.Net® Sound Masking,
Paging and Music System. The Touch Pad option is often chosen
for spaces such as conference rooms and board rooms, or any area
where individualized and on-going adjustments are desired.

Located on the wall plate used for the Touch Pad is an LED light

indicator that identies the current function of the system that

is being adjusted. The system functions that can be adjusted are
masking, paging, music, test and IR/ALL.

To use the Touch Pad use the left and right arrow keys in the center
of the pad to select the function types (masking, paging, music,
test, IR/ALL) that you wish to adjust. Once the system function is
selected, use the up and down arrows to make increases or de­creases in the volume adjustments.

To mute and un-mute the system, simply press the Mute/Un-mute
button located at the bottom of the wall plate. The IR/All function
enables end users to mute or unmute the masking, paging and
music all at the same time.

Touch pad wall plate can be attached to vertical surface with two
screws.

WALL PLATE
+ Dimensions – 2 ¾”w x 4 ¼”h
+ Touch pad wall plate can be attached to vertical surface with

two screws

WIRE REQUIREMENTS
+ Cat 5e cable or equivalent 4 Twisted pair
+ Standard RJ45 connector

INSTALLATION

To connect to the Spectra i.Net® System’s OP, use a patch cable us­ing Cat 5E with RJ45 connectors and connect the wire from the OP’s

IR Port to the back of the wall plate. If an IR Hub has been specied

for multiple controls, the patch cable can be run from the OP to an
IR Hub and then to each channel of the IR Hub (A, B, C, D).

v2.0
Lencore Acoustics Corp. One Crossways Park Drive West Woodbury, NY 11797 p 516-682-9292 f 516-682-4785 [e-mail]
Spectra i.Net®, Spectra®, CrossNetOne™, CrosswaysOne™ are trademarks of Lencore Acoustics Corp. All rights reserved. © Copyright 2013

SPECTRA – i.Net

IR TOUCH PAD CONTROLLER CONFIGURATION MANUAL

®

Model

G41

Front of Wall Plate

Back of Wall Plate (board turned right 90°)

The IR Touch Pad Controller comes with all dip switches in the down
position by default.

This default setting will allow the IR Touch pad controller to be used
with the IR Hub model G482 out of the box. If you do not have the
IR Hub model G482 you can connect the IR touch pad directly to an

OP. This will require conguration.

PROGRAMMING THE IR TOUCH PAD
CONTROLLER:

The conguration of the IR touch pad controller is done thru dip

switches located on the back side of the board. (See diagram
above)

The list below shows all possible congurations for the IR touch
pad. Congurations will allow you to: control individual channels
such as channel A, B, C, D (individually) or All channels, also cong-

ure whether or not the switch (buttons) on the front panel of the IR
touch pad are active or not and if the IR sensor is active or not.

To congure dip switches: locate the back of the IR touch pad and

turn board to the right 90o. The RJ45 connector receptacle will now
be oriented towards the right. The small pins numbered 1-8 will
now be in the middle left of the board. Thee small pins can be set
to either “UP” or “DOWN” which can be done with a small screw­driver.

Exploded View: Dip Switches (on board turned right 90°)

OTHER SYSTEMS ALSO AVAILABLE

Spectra®, Spectra Tangent™, Spectra Emerald™

v2.0
Lencore Acoustics Corp. One Crossways Park Drive West Woodbury, NY 11797 p 516-682-9292 f 516-682-4785 [e-mail]
Spectra i.Net®, Spectra®, CrossNetOne™, CrosswaysOne™ are trademarks of Lencore Acoustics Corp. All rights reserved. © Copyright 2013

Use the list below to nd what dip switches need to be changes for

your particular install.