Lenco IR-1650 User Manual

User Manual

Internet Radio

IR-1650

For information and support, www.lenco.eu

Please read this user manual carefully before using the receiver.

LOCATION OF CONTROLS

1.LCD Display

2.Play/Pause/Stop or
Preset I

3.Previous or Preset II

4.Next or Preset III

5.Dial/Volume

6.Alarm

7.Back

8.On/Off

9.Speaker

10.DC Socket

11.Line Out

12.Earphone jack

Key Functions:

ON/OFF:

BACK:

ALARM:

I , II , III:

:

:

Dial/Volume: Use to search for stations, use to change the option shown on the display,

Use to adjust the volume.

:

Press to switch the internet radio Stand By on/off.

Press to go back to the previous display.

Alarm Setting

Use to

Press to pause or playback and hold to stop playback.

Press to start playback at the previous track.

Press to start playback at the next track.

store and play up to the radios.

SETTING UP

Those steps for connecting your radio to your network

Step 1 Switching on the radio

Plug the cable from the AC adapter into the socket labeled 7.5V 1.2A DC on the back of the radio, then
switch on at the mains.
Caution: Use only the mains adapter supplied with the radio. Connecting a power supply with a different
rating will cause permanent damage to the radio and may be hazardous.

The display on the front of the radio will light up and say:

Then show

After a few seconds, it will shows :

If it complete the initialing, it will auto scan the ESSID as

Then it will list all the ESSID names it can find, you can select one of you want to use, maybe it will
request you input the correct WEP(Wired Equivalent Privacy) or WPA(Wi-Fi Protected Access) code. If
your network is not configured to need a WEP or a WPA code, the unit will connect to the ESSID auto
and success as

Or if you are requested to input the encryption, you can do as

1. Select the one you want to use

2. Then it will show you

LENCO

Internet Radio

SP Radio

ARM Powered

Initializing

WiFi Network

Scanning

…….

Network OK

<your network>

Enter WPA/WEP key

Note: The encryption code would have been set up by the person who set up and configured your
network.
After 3seconds the display goes into the code entry mode or press select.

If the display does not automatically go into code entry mode, press the SELECT button. To enter
the code, use the DAIL to select each character of the code in turn, pressing the SELECT button
after each character.

3. Make sure the character you want is shown in the centre of the display to be able to select it.

4.If you complete the key then you can use “END” to confirm. The display shows “Connect WiFI” as the
radio connects to the network.

5.If the connecting is OK, it will show you

6.Now you can go to listen to the internet radio:

< END <> 0 1234 >

Connect WiFi

Connecting /

Network OK

<Stations>

Media Player

Changing the volume:

You can change the volume by turning the TUNE clockwise to increase the volume and anticlockwise to
decrease the volume. The display shows the volume bar. You cannot change the volume when you are
in a menu or when the radio is connecting to a station.

Step 2 How to set your radio

In the main menu, you will see below the settings.

Stations

Media
Player

Configure Network Config

By Region

By Genre

User

UPNP Servers

Playback Mode

Clear Queue

Repeat / Shuffle

Scan for Networks

Enter network Name

View Config

Edit Config

Signal Warning

Version

Upgrade Firmware

Language

Factory Reset

Register

Clock

Sleep Timer

Backlight

Weather

RSS Feed

Signal strenght

English, Spanish, French, German, Dutch
and Hungarian

Set Time

Set Alarm

0-90 minutes

Active/Inactive/Standby

Listen to your internet radio

When playing a stream, the Internet Radio, downloads a small amount of the stream before it starts
playing. This will occur before your selected station starts to play.
In the <Stations > menu, you can select one of them with highlighted then press the select button.

1. <By Region>enables

You need to choose a Continent and then a country from that continent. You can then select from a list
of radio stations from your chose country.

2. < By Genre > enables
You need to choose radio stations according to their content, for example News, News, Oldies
or Rock etc.

5. < User >
You can find the radio stations which you have added to your internet radio station list in the website,

please refer to

6. Press the “Select” button to choose the station you want to listen

Configuring “My Stuff”.

<By Region>

Genre

Caribbean

<Europe>

<UK>

Ukraine

Hard Rock

<Hip Hop>

Internet Radio

Wait…