Lenco IPD-5250 User Manual

INSTRUCTION MANUAL

FM RADIO WITH iPod/iPhone DOCKING

MODEL: IPD-5250

Please read following instructions prior to operating your unit.

Manufacturer of this unit follows a principle of continuous improvement and has no responsibility for any changes that are made to the unit nor any liability for these changes. Thanks for your choice of our products.

For information and support, www.lenco.eu

1 2 4 5

678910 11126

13 14 15 16

17 18 19 20

MAIN UNIT

1. FM ANTENNA

2. iPod/iPhone DOCKING

3. BRACKET

4. BRACKET ADJUSTING BUTTON

5. HANDLE

6. SPEAKERS

7. MEMORY BUTTON

8. FUNCTION BUTTON

9. REMOTE SENSOR

10. LCD DISPLAY

11. STANDBY BUTTON

12. TUNE BUTTON

13. CH- BUTTON

14. VOL- BUTTON

15. VOL+ BUTTON

16. CH+ BUTTON

17. BATTERY COMPARTMENT

18. AUX IN JACK

19. VIDEO OUT JACK

20. DC IN JACK

0 1

STANDBY

SLEEP

MUTE

iPod/

iPhone

AUX IN

2. SLEEP BUTTON

3. iPod/iPhone BUTTON

4. PLAY/PAUSE BUTTON

5. PREVIOUS BUTTON

6. CH+/- BUTTON

7. TUNE+/- BUTTON

8. FAST BACKWARD BUTTON

9. MEM BUTTON

10. RAN BUTTON

1. MUTE BUTTON

TUNECH

VOL

11. STANDBY BUTTON

12. FM BUTTON

13. AUX IN BUTTON

14. NEXT BUTTON

15. VOL+/- BUTTON

16. FAST FORWARD BUTTON

17. ST/MO BUTTON

18. REP BUTTON

MEM

RAN

REPST/MO

16 17

POWER SUPPLY

Plug the adapter to the unit and the main power.

SLEEP TIMER SETTING

Following the below instructions to set the sleep time at power on mode: During playback, press SLEEP button repeatedly to cycle through the sleep time options:

90 ➨ 60 ➨30 ➨ 15 ➨ 05 ➨ OFF

Once the options you want shows on the screen, release the sleep button. After setting the sleep time, you can operate the unit freely. When the set sleep time has expired, the unit will automatically power off.

iPod/iPhone OPERATING PLAYING AN iPod/iPhone

1. Dock the iPod/iPhone on to the unit. Power on the unit by pressing STANDBY button, then press FUNCTION button on the unit repeatedly or press iPod/iPhone button on the remote to switch to iPod/iPhone mode.

2. Press PLAY/PAUSE button to start/pause the playback.

3. Press NEXT button to skip to the next track/chapter. Press PREVIOUS button to skip to the previous track/chapter.

4. Press and hold FAST FORWARD/BACKWARD button to search through the track/ chapter forward or backward.

5. Press RAN button to enable or disable random playback.

6. Press REP button repeatedly to repeat a single track/chapter, repeat all tracks/chapters or disable the repeat function.

NOTE: During playback, the connected iPod/iPhone may skip to another song accidently. Once the problem occurs, please set the iPod/iPhone to shake off.

FM RADIO TUNING THE FM RADIO

1. Power on the unit, switch to RADIO mode by pressing FUNCTION button on the unit repeatedly or pressing FM button on the remote.

2. Press TUNE+/- button on the remote to fine tune the radio station. Press and hold TUNE+/- buttons on the remote to auto search radio station forward or backward respectively or press TUNE button on the unit to tune the radio station automatically. When an available station will be found, the unit will broadcast it immediately and the searching will be stopped.

3. Press ST/MO button on the remote to switch between FM mono and FM stereo modes.

STORING YOUR FAVORITE RADIO STATION

1. During playback, press MEM button on the remote or press MEMORY button on the unit, “MEM” flashes on the screen with a memory cell number.

2. Press CH+/- button to select the corresponding memory cell among P01-P20 for storing the station.

3. Press MEM button on the remote or MEMORY button on the unit to store the current station to the selected memory cell.

4. During radio playback, press CH+/- button to recall the stored stations.

AUX IN

Follow below steps to connect the unit to another audio device like MP3 player and the like:

1. Connect the Audio Out of the device to AUX IN jack with audio cable.

2. Press STANDBY button to turn the unit on.

3. Press FUNCTION button on the unit repeatedly or press AUX IN button on the remote to switch the unit to AUX mode.

4. Power on the device and begin playback.

MUTE

During playback, press MUTE button to switch off the audio, press the button again to resume the audio.

VOLUME LEVEL JUSTMENT

During playback, press VOL +/- button to adjust the volume output level.

VIDEO OUTPUT

1. Dock the iPod/iPhone to the unit.

2. Connect a RCA cable to the Video Out on the unit and a television.

3. Power on the TV set and the unit. Press FUNCTION button on the unit repeatedly or press iPod/iPhone button on the remote to switch to iPod mode.

4. Adjust the connected television to the proper input setting.

5. Video from a docked iPhone/iPod can now be played through the unit to the connected television.

Note: Make sure the docked iPhone or iPod’s TV out option is turned on.

2 3

+ 1 hidden pages