LEGRAND Wattstopper EQ41-LCAP Installation Instructions Manual

Wattstopper

Architectural Dimming Equinox 41 LCD Keypad
French Description

No: IS-00711 – rev. A

EQ41-LCAP • Les Numéros de Catalogue • Los Números de Catálogo:

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

Spanish Description

Installation Instructions • Instructions d’Installation • Instrucciones de Instalación

®

Are...

Legrand’s Equinox 41-LCAP LCD Touchscreen is designed to be installed in a single gang box and
is a similar size to traditional keypads. Legrand’s Equinox 41-LCAP uses self discovering widgets,
eliminating countless hours of tedious programming. Navigate and control, with real time feedback.
Widgets may be further personalized or additional controls setup directly on the touchscreen, by
selecting the Settings Menu in the upper right hand corner of the screen with the gear symbol . In
the settings menu the administrator of the system can change or create the following: scenes, event
timers, schedules, etc. The interface uses intuitive gestures; swipe left and right to change widgets,
touch and release for normal button operation, or press and hold for dim-cycle, shade controls, etc.

OVERVIEW

FEATURES AND OPERATION OVERVIEW

• Vertical screen orientation displays main room button screen, as a default, with all widgets appropriate for the space where the
touchscreen is located, in the widget bar

• Equinox platform provides built-in widgets using Legrand’s proprietary auto discovery widgets for fast automatic screen design

• Equinox 41-LCAP incorporates consistent user experience interface. In-wall touchscreens, tablets and smart phones use the
same user interface

• Power over Ethernet, PoE or PoE+

- PoE optional Ethernet 4 Port PoE Injector part number DA2400 or COM-POE-SWITCH

• Communicates over Ethernet, via Ethernet Bus

• Firmware upgradeable over Ethernet from Design Center

• Built-in ambient light sensor for “Active,” AUTO mode screen brightness

• Built-in proximity activation, 6” maximum, may be programmed to execute a task with a hand wave across front of station

• Dual operation mechanical buttons, bottom left and right;

- Left navigates to default widget

- Right may be programmed with a task from Design Center

• Three types of users are supported on the system. Using a variety of users you can limit what is available to specic individuals
as well as limit permissions.

- Administrators - All permissions and visibility into the system. Only one system-wide administrator can be assigned whose

password is set up at system startup. The admin password can be created or changed from within Equinox view. It is not

dependent on the rst time initialization screen.

- Managed Users - A password protected user who can have a wide variety of permissions granted to them, including the

creation of other users. There is no limit to the number of managed users.

- Guest Users - Recommended to be the default user on all screens in public areas, guest users cannot make any changes

to the system and have no permissions to set. They cannot be password protected.

• Top of screen displays:

- Administrator/user details

- Access help topics

- Manage settings including appearance, access/permissions, areas and rooms, devices, events, groups, repair, schedules,

scenes, and systems

• Main screen automatically displays widgets based on Design Center project le (order may be changed in user/settings directly
from the app) including shades, lighting, home, and scenes

• Raise/lower dimmable loads, shades, hue and intensity settings using sliders

1

FEATURES AND OPERATION OVERVIEW (continued)

NOTE: If buttons are held in too long, the screen will boot to service

mode, and will not load the application code. Repeat manual reboot
– without holding buttons to long – to clear this mode.

• Station reset – simultaneously press and hold both mechanical buttons for three seconds until the screen goes dark, then release

• Station reset into Service Mode – simultaneously press and hold both mechanical buttons for ten seconds

- Service mode is automatically used when updating rmware from Design Center

- If the application code is corrupt it may cause the screen to lock, preventing Design Center from updating or reloading the

rmware. Use this option to reboot the screen to service mode allowing Design Center to update the corrupted rmware.

- To manually exit Server Mode use the Station Reset option (above)

SPECIFICATIONS

Description Specication

Dimensions, HWD (at wall surface) 4.9” x 3.44” x 0.44” (124mm x 87mm x 11mm)

Dimensions, HWD (overall) 4.9” x 3.44” x 1.1” (124mm x 87mm x 28mm)

Finished Weight 8.8 oz. or 249.5g

Power Ethernet with PoE, PoE+, 5W

Wiring Connections Communication and power: PoE/PoE+ via Ethernet RJ45

Surge Suppression Yes

Maximum Gangs Single gang only

LCD Button Status Automatic (white = off, orange = on)

Mounting US/European style, single gang, wall boxes or low-voltage brackets

Addressing Self-addressing through software

Finish Trim: Titanium, Touchscreen: Black glass

Glass Surface Chemically strengthened

Ambient Operating Temperature 32-95°F (0-35°C)

Ambient Operating Humidity 5-95% non-condensing

CE/FCC Compliant Yes

Equinox 41-LCAP is compatible with InFusion Design Center version 3.8 software or higher. For new projects it is recommended that
rmware and software be kept to the most current release.

Installation of Legrand products should be performed or supervised by a certied Legrand installer. The Equinox 41-LCAP

touchscreen installs into US/European style, single gang, wall boxes or low-voltage brackets. Connect to local network via PoE/PoE+

RJ45 Ethernet connection.

No: IS-00711 – Rev. A

SYSTEM REQUIREMENTS

INSTALLATION

2

in station bottom

B

ETHERNET PoE or PoE+

INSTALLATION OVERVIEW

EQUINOX 41-LCAP

TOUCHSCREEN

Harv...

Open Rest Ge...

RJ45 CONNECTOR

PoE/PoE+

ETHERNET BUS

SCREWS*

4 SQUARE JUNCTION

NETWORK PANEL

OR SWITCH

*Ethernet Bus: Power and communication; Ethernet, PoE or PoE+, (Optional) - Ethernet 4 Port PoE Injector (part# DA2400)

BOX RING

*Use flat-head
screws provided
US – 6-32 x 0.75”

EQUINOX 41-LCAP

LCD SCREEN

EQUINOX 41-LCAP STATION INSTALLATION STEPS

1. Run PoE Ethernet bus to four square junction box

2. Install ring with screws provided (gure A)

3. Connect RJ45 to station

4. Install station by rotating (gure B) and connecting the top rst.

Press station in and hold on bottom center while securing the hex
screw with provided allen wrench (gure C)

A

No: IS-00711 – Rev. A

Press and hold here on

front, bottom center

1/16” HEX

C

Set 1/16” hex screw

3