LEGRAND Kenall TEKDEK TD17 Series, Kenall TEKDEK LED TD17 Series Installation Instructions Manual
TEKDEK
SAFETY RECOMMENDATION
A 1/16" diameter aircraft cable with end-loop (not included) is recommended for
attaching the xture structural to the upper structural.
™
LED
Luminaire for Parking Garages
TD17 SERIES
INSTALLATION INSTRUCTIONS
1
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should
always be followed, including the following:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ÊTRE INSTALLÉ EN CONFORMITÉ AVEC LE CODE DE
L'INSTALLATION PAR UNE PERSONNE QUI connaît BIEN LA CONSTRUCTION ET
LE FONCTIONNEMENT DU PRODUIT ET LES RISQUES ENCOURUS.
DISCONNECT POWER TO ALL CIRCUITS BEFORE WIRING FIXTURE. INSTALL IN
ACCORDANCE WITH ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT
CONNECT TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS AND
LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE. SUPPLEMENTAL
INSTRUCTIONS MAY BE LOCATED ON THE FIXTURE, IN ADDITION TO THIS
INSTRUCTION SHEET, REGARDING ORIENTATION, OR MOUNTING RESTRICTIONS.
SAVE THESE INSTRUCTIONS
SAFETY RECOMMENDATION
A 1/16" diameter cable with end-loop (not included) is recommended
for attaching the xture structural to the upper structural
AIRCRAFT CABLE ATTACH
1/16" DIA. AIRCRAFT CABLE
(SUPPLIED BY OTHERS)
TO UPPER STRUCTURAL
SCREW (SUPPLIED BY OTHERS)
www.kenall.com | P: 800-4-Kenall | F: 262-891-9701 | 10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United State swith more than 50% of the component cost of US origin It may be covered by patents
found at www.kenall.com/patents. Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
F-4260_091118
DIRECT TO SURFACE INSTALLATION
1: Remove tertiary lens (if provided) by unscrewing (4) captive screws.
INSTALLATION INSTRUCTIONS
2
2: Remove heatsinking/LED base by unscrewing (4) captive screws.
These will be the inner most screws.
3: Disconnect the quick connector wires from the LED board and
the driver.
4: Make electrical connection to J-box (for sizes, see next page). Circuit
wire connection must be in J-box. Install housing to surface using (4)
5/16" diameter mounting holes.
5: Re-assemble by reversing the removal procedure.
HOUSING TOP VIEW
QUICK CONNECT
CAPTIVE SCREWS (4)
HOUSING
DRIVER
HEATSINK/LED BASE
CAPTIVE SCREWS (4)
FOR REMOVING HEATSINK
5/16” MOUNTING HOLES (4)
TERTIARY LENS (IF PROVIDED)
www.kenall.com | P: 800-4-Kenall | F: 262-891-9701 | 10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United State swith more than 50% of the component cost of US origin It may be covered by patents
found at www.kenall.com/patents. Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
F-4260_091118
QUICK MOUNT KIT INSTALLATION
INSTALLATION INSTRUCTIONS
2
1: Quick mount plate fastens to a secure J-box.
Screws by others.
2: Align hanger bracket with center slot on
top of xture as shown at right. Fixture
can then hang from bracket while electrical
connections are made.
3: After excess wires are in J-box (see sizes
below), push the xture up to the mounting
plate. Locking hooks should slide through
slots. Twist xture until a “click” is felt or
heard. Fixture is now in place.
USED WITH THE FOLLOWING
JUNCTION BOX SIZES:
4" ROUND
4" SQUARE
3-1/2" OCTAGON
2.50
3.37
3.37
2.50
LOCKING HOOKS
1.
HANGER BRACKET
2.
ALIGN HANGER BRACKET
WITH CENTER SLOT
LOCKING HOOK
3.
SLOTS
QUICK MOUNT PLATE
3.50
4.77
F-4258_091118
Loading...