LEGRAND Kenall LUXTRAN LTSIU Series Installation Instructions Manual
LUXTRAN
™
Luminaires for Tunnel Applications
INSTALLATION INSTRUCTIONS
1
LTSIU SERIES
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions
should always be followed, including the following:
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR
WITH THE CONSTRUCTION AND OPERATION OF
THE PRODUCT AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE
CODE D’INSTALLATION PERTINENT, PAR UNE
PERSONNE QUI CONNAÎT BIEN LE PRODUIT
ET SON FONCTIONNEMENT AINSI QUE LES
RISQUES INHÉRENTS. DISCONNECT POWER TO ALL
CIRCUITS BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE
WITH ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT
CONNECT TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE
MARKINGS AND LABELS TO ENSURE CORRECT INSTALLATION
OF FIXTURE. SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED
ON THE FIXTURE, IN ADDITION TO THIS INSTRUCTION SHEET,
REGARDING ORIENTATION, OR MOUNTING RESTRICTIONS.
SAVE THESE INSTRUCTIONS
The LuxTran LTSIU series luminaires contains sensitive electronics. Take care to avoid damage by improper handling or
static electricity discharge (ESD). Either type of damage could render the system inoperable or cause latent failure.
INSTALLATION INSTRUCTIONS
1. Secure xture to wall or ceiling using user supplied hardware. Slots for 3/8 bolts are provided in the mounting
brackets. See Figure 1.
.44
.94
10.0
25.5
.41
.91
4.00
25.37
9.75
Figure 1b
20°
20°
5.95
Figure 1a
Figure 1
NOTE: If the xture has directional optics, note the label indicating the direction of light and install appropriately.
www.kenall.com | P: 800-4-Kenall | F: 262-891-9701 | 10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United State swith more than 50% of the component cost of US origin It may be covered by patents
found at www.kenall.com/patents. Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
LTSIU_F-5445_091118
INSTALLATION INSTRUCTIONS
2. Rotate latches and open door, which is retained by stainless steel cables.
3. Loosen wing nuts and remove Wiring Cover. See gure 2.
Figure 2
4. Connect weather tight electrical service to 7/8 dia. opening provided.
5. Connect electrical service:
Black- input line, 120-277VAC or 277-480VAC (refer to label for correct input voltage)
White- Neutral
2
Copper- ground
6. Replace Wiring Cover and secure with wing nuts.
7. Close door and secure rotating latches.
SERVICE INSTRUCTIONS
LTSIU series LED modules are not eld replacable.
LED module replacement may be done after the xture is removed from service.
Before beginning any service operation, be sure the power to the xture is off.
To replace an LED driver-
1. Open door, which is retained by stainless steel cables.
2. Loosen wing nuts and remove Wiring Cover.
See Figure 3.
3. Disconnect the driver to be replaced.
4. Remove the retaining strap which secures
the driver. See gure 3.
5. Install new driver and secure using
restraining strap.
6. Connect to LED modules following the
wiring diagram for the particular xture.
www.kenall.com | P: 800-4-Kenall | F: 262-891-9701 | 10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United State swith more than 50% of the component cost of US origin It may be covered by patents
found at www.kenall.com/patents. Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
Figure 3
LTSIU_F-5445_091118
Loading...