Legrand IS-0433 User Manual

301 Fulling Mill Road, Suite G Middletown, PA 17057 Phone (800) 321-2343 / Fax (717) 702-2546 www.onqlegrand.com

1. INTRODUCTION

The Legrand LCD Console with High Performance lyriQ™ (P/N HA5010-xx) provides a large, easy-tooperate user interface from which a homeowner can control all Unity system features in the home (see Figure 1). The Console, coupled with built in lyriQ™ functionality eliminates the need for a separate High Performance Keypad Volume Control and Intercom Room Unit in this zone.

NOTE: This product requires connection of the LCD Console to an HA6001 Integration Module and lyriQ™ High Performance audio system.

INSTRUCTION / INSTALLATION SHEET LCD Console w/High Performance lyriQ™

IS-0433 Rev. A

2. FEATURES

The LCD Panel Display features:

• Large 7" LCD screen with adjustable color, contrast and brightness

• Installation requires just two Cat 5 cables and three 16/2 speaker cables:

o One Cat 5 cable to HA6001 Integration Module

o One Cat 5 cable to AU1002 or AU1014 lyriQ™ Audio Distribution Module

o One 16/2 speaker cable to High Performance lyriQ™ Power Module

o One 16/2 speaker cable to each of the two supported room speakers

• Backlit keys for easy navigation

• Integrated LCD Console speaker for camera and intercom audio with adjustable audio level with mute capability

• Four Quick-Menu buttons for easy navigation of the Unity interface

• IR receiver window supporting full Remote Control operation of the LCD Console, including lyriQ™ control functions

• Adjustable automatic power-off timeout

• Twenty watts per channel class D lyriQ™ audio amplifier

• Functions as a Selective Call Intercom Room station

3. INSTALLATION

NOTE: The Integration Module provides power, display, audio, and video (camera images) to the LCD Console. The Integration Module can operate up to two LCD Consoles; repeat the procedure below for each LCD Console to be installed. The LCD Console may also be used as a lyriQ™ high performance volume control, with the distributed audio signal and audio power supplied by the lyriQ™ Distribution and Power Module.

A. At the selected LCD Console location, install a plastic triple-gang box like the

Slater® P3-54-RACMH (a low voltage bracket may also be used).

B. Home-run two Category 5 cables and one 16/2 speaker cable from the LCD

Console location to the enclosure location where the Integration Module, lyriQ™ Audio Distribution Module and High Performance Power Module reside.

C. Run two 16/2 speaker cables from the LCD Console location to the location

where the two room speakers will reside.

NOTE: Leave extra cable at each end. At the LCD Console location, feed the Category 5 cables into the lower left corner of the gang box then pull them through (see Figure 3). The 16/2 HP power and 16/2 speaker cables can be fed through a different (upper) knockout of the gang box as shown in Figure 3. Remove any outer bundling jackets for easier LCD Console insertion. At the enclosure, route the cable through the top of the enclosure, enough so that the cable reaches the various modules without stretching.

D. Terminate both ends of the Category 5 cables from the LCD Console, using RJ45 Plugs, according to the T568A wiring

standard (see Figure 2).

CAUTION: Be certain to properly label each cable, as reversal can cause equipment damage.

E. At the LCD Console location, use the included screws to fasten the display mounting bracket to the gang box.

IMPORTANT: Pull the cables coming through the gang box through the opening in the mounting bracket prior to fastening the bracket to the box (see Figure 3).

F. Insert the RJ-45 plug from the Integration Module into the lower RJ-45 jack located on the rear of the LCD Console (see Figure 4) and

insert the RJ-45 plug from the lyriQ™ Distribution Module into the upper RJ-45 jack located on the rear of the LCD Console (see

Figure 4). The 16/2 power cable is attached to the two screw terminals of the 2-position connector on the rear of the LCD Console (see Figure 4). The two 16/2 speaker cables are attached to the four speaker screw terminals of the 6-position connector on the rear of the LCD Console (see Figure 4).

Figure 1

Figure 2

301 Fulling Mill Road, Suite G Middletown, PA 17057 Phone (800) 321-2343 / Fax (717) 702-2546 www.onqlegrand.com

NOTE: The other two screw terminals on the six position connector (see Figure 4) are for connection to a sub-woofer.

G. Feed any excess cable back into the wall.

H. Angle the LCD Console into the wall bracket engaging the right side latches first. Then push in the left side of the LCD Console until the

top and bottom latches are engaged and you hear an audible snap.

NOTE: To remove the LCD Console from the bracket, simply slide a credit card or guitar pick along either the right-hand or lefthand edge of the LCD Console to detach the retaining clips.

I. At the enclosure location, insert the LCD RJ45 plug from the LCD Console location into an available LCD RJ45 jack on the Integration

Module. Insert the lyriQ™ RJ45 plug from the LCD Console location into an available zone RJ45 jack on the lyriQ™ Audio Distribution Module. Connect the 16/2 HP power wires to the High Performance Power Distribution Module.

J. At the speaker locations, connect the 16/2 speaker cables to the connectors on the rear of the speakers and mount the speakers in

their location.

K. Apply power to the Integration Module, Audio Distribution Module and HP Power Distribution Module and test for LED illumination at

the LCD Console.

Figure 3

INSTRUCTION / INSTALLATION SHEET LCD Console w/High Performance lyriQ™

IS-0433 Rev. A

Figure 4 Rear View of LCD Console wHP /lyriQ™

4. OPERATION

NOTE: This Instruction/Installation Sheet provides a brief overview of LCD Console functionality. Please refer to Figure 6 for a list of Instruction/Installation Sheets for other products referenced here. Refer to Figure 5 during this section.

A. POWER

Turn the unit on (active) or off (standby) by pressing the Power button.

• When active, the power indication LED located behind the power button illuminates white, and all other buttons are backlit white.

• When in standby, the power indication LED located behind the power button illuminates red and the display, speaker, and backlighting are effectively turned off. To come out of standby, simply press the power button again.

• The LCD Console can be programmed to enter standby after a certain period of time passes. The user-selectable settings for active time are 5 minutes (factory default), 10, 15, 30 minutes, or 1 hour.

B. SOFT BUTTONS

The four soft buttons are used to activate the selection indicated just above the button on the user interface screens.

Figure 5

+ 1 hidden pages