LEGRAND HKRL10, HKRP10 Installation Manual
installation guide
Smart Switch
with HomeKit Technology
Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HKRL10
table of contents
before you start ..................................3
what you need ...................................4
getting to know your switch ..........6-7
installation and setup ................ 8–23
specifications ............................. 24-25
2
faqs ....................................... 25–29
regulatory information ......... 30–33
warranty .......................................34
support ........................................35
before you start
Review this guide in its entirety before beginning device installation. Consult an
electrician with any questions or if you are unsure of your abilities.
DWarning: Incorrect installation could
result in death, serious injury, and/or
damage to your home or devices.
DCaution: To reduce the risk of injury
and/or overheating and damage to other
equipment:
• For dry, indoor use only.
• Do not use to power medical equipment.
• Not suitable as a disconnecting means.
Visit the Legrand website at www.legrand.us/radiant/homekit.aspx to learn more about
your smart device.
• Do not use with loads exceeding the
device load rating (see page 24).
• Connect the smart switch to a
120 VAC, 60 Hz power source ONLY.
• Always use copper wire to install the
smart switch and follow all applicable
local and national electrical codes.
• Install in a non-metallic electrical box
to protect wireless signal strength.
3
what you need
REQUIRED:
Phillips-head screwdriver
Flat blade screwdriver
YOU MAY ALSO NEED:
Non-contact voltage tester, pliers, wire cutter, wire stripper, electrical tape,
flashlight, radiant
wire nuts (included)
NOTE: Exercise caution when using power tools. Overtightening the screws can
damage the device.
4
®
screwless wallplate (included), wiring leads (included), and
5
getting to know your switch
Item Name Description
• Press the top of the paddle to turn the light on
and the bottom to turn the light off.
1 Paddle Switch
2 LED Locator Light
NOTE: For in-wall control of this switch in a three-way application, refer to the installation
instructions for the HomeKit Remote Switch (HKRL20).
6
• To return the switch to factory default, press and
hold the top of the paddle for 15 seconds. Then,
remove the device from the Legrand Home app
(or Apple Home app).
Indicates the current state of the device. Refer to
“LED Locator Light Explanations” for detail.
LED LOCATOR LIGHT EXPLANATIONS
2
1
LED
State of Light Explanation
Color
Slowly Flashing
Amber
Solid White Connected to Wi-Fi and turned off
No Light Device is on
Rapidly Flashing
Amber
Device is attempting to connect to
the network
N-Way Pairing mode: device is
ready to pair with the remote(s)
7
installation & setup
step one | turn off the power for your device at the
circuit breaker
Flip the existing light switch multiple times to confirm the power is off.
NOTES:
• If there are multiple devices next to your existing light switch, make sure power is
off at the circuit breaker for all of those devices.
• For multi-way installations using a remote switch, follow the instructions for the
remote device (HKRL20).
8
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
9
installation & setup
step two | remove the existing device
Check for the following wires:
1
HOT or LINE: Receives power from the circuit box. Referred to as “hot” for the
purposes of this guide. Do not touch or let “hot” wires contact other wires.
2
LOAD: Directs power to your light(s).
3
NEUTRAL: Creates a path to return current to the power source when the
device is off. Required for your switch installation.
4
GROUND: Provides a safe path for electricity in the event of a short circuit.
NOTE: Refer to the “faqs” on page25 if you are unsure of your wiring.
10
VOLTAGE
TESTER
Load
ON
OFF
ON
OFF
ON
OFF
Supply
“Hot”
11
Loading...