Legrand HA6101 User Manual

301Fulling Mill Road, Suite G Middletown, PA 17057 Phone (800) 321-2343 / Fax (717) 702-2546 www.onqlegrand.com

1. INTRODUCTION

The Legrand Integration Expansion Module (P/N HA6101) is used to expand the number of user interface devices supported by the Legrand Integration Module (P/N HA6001) for larger Unity systems. It is available as part of three different kits, adding interface #3 & #4,#5 & #6 and #7 & #8 (see Figure 2). It connects to the Integration Module (or other Integration Expansion Module) with two cables. One is a standard Cat 5 cable attached to the Cascade jacks, and the other is a provided special 1-to-2 cable that attaches to the Q-Link Video Cascade jacks (see Figure 2).

NOTE: The 1-to-2 cable must be installed with cable end #1 going to Q-Link Video jack #1 and cable end #2 going to Q-Link Video jack #2 for proper system functionality.

NOTE: The HA6101 is powered by one PW1060 24VDC, 60W Power Supply, which is sold separately.

INSTRUCTION / INSTALLATION SHEET Integration Expansion Module

IS-0466 Rev. O

2. DESCRIPTION

A. CONNECTIONS

The Legrand Integration Expansion Module features:

• Two (2) RJ45 jacks labeled “LCD/TV” for connection to LCD Consoles or TV Display Interfaces

• Two (2) RJ45 jacks labeled “Cameras” for connection to Cameras via the CM1048 Combination LCD/Camera Distribution Module, or CM1010 LCD Module

• Eight (8) RJ45 jacks labeled “Q-Link 3-10” for connection to Selective Call Intercom devices

• Two (2) RJ45 jacks labeled “Lan 1 or Lan 2” for connection to a Router or other device that provides DHCP IP

addresses (Both are necessary for module to function)

• Two (2) RJ45 jacks Labeled “Q-Link Video 1 or 2” for connection to HA6001 Integration Module or HA6101 Integration Expansion Module via the provided 1-to-2 cable (Cable is necessary for module to function)

• One (1) RJ45 jack labeled “Q-Link Video Cascade” for connection via the provided 1-to-2 cable to the next Integration Expansion Module (if required)

NOTE: On the HA6101 Integration Expansion Module, the two (2) RJ45 jacks labeled “Q-Link Video” are NOT connected to SCI Video Door Units (as on HA6001), and are used only for module interconnection

• Two (2) Cascade RJ45 jacks labeled “In” and “Out” for connection to the Integration Module or other Integration Expansion Module (Necessary for module to function)

B. EXPANSION SUPPORT

The first Integration Expansion Module Kit (P/N HA6452) provides support for:

• Two (2) additional Unity GUIs (System total 4) and includes the CM1048 Combination LCD/Camera Module

• Eight (8) additional RJ45 jacks for Selective Call Intercom devices (see Figure 2)

The second Integration Expansion Module Kit (P/N HA6454) provides support for:

• Two (2) additional Unity GUIs (System total 6) and includes an additional CM1010 LCD Module

• Eight (8) additional RJ45 jacks for Selective Call Intercom devices (see Figure 2)

The third Integration Expansion Module Kit (P/N HA6456) provides support for:

• Two (2) additional Unity GUIs (System total 8)

• Eight (8) additional RJ45 jacks for Selective Call Intercom devices (see Figure 2)

NOTE: Regardless of how many Integration Expansion Module Kits are used, there is still a 32 node limit on the total number of supported SCI devices in one system. This 32 node limit includes LCD Consoles, but does not include TV Display Interfaces.

Figure 1

INSTRUCTION / INSTALLATION SHEET Integration Expansion Module

301Fulling Mill Road, Suite G Middletown, PA 17057 Phone (800) 321-2343 / Fax (717) 702-2546 www.onqlegrand.com

NOTE: Although not shown below, all “Lan” jacks must be connected to a router port for the modules to function.

Figure 2

3. INSTALLATION

A. WIRING

All interfaces on the Integration Expansion Module are RJ45 jacks which require Cat 5 cables to be terminated using the T568A wiring standard shown in Figure 3.

NOTE: All devices in a Unity system should be powered up at the same time (i.e. use a common power strip for the individual AC adapters).

NOTE: The HA6101 is configured via any LCD Console/TVDI or via the web-based configuration interface, accessed by entering the system IP address (found under Setup/Network Info) into your PC web browser (PC must be on same data network as Unity System.

IS-0466 Rev. O

Figure 3