Page 1
I N S T A L L A T I O N I N S T R U C T I O N S
Floor to Ceiling Back to Back Accessory
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PACFCB
Page 2
PACFCB Installation Instructions
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries
(collectively “Legrand | AV”), intend to make this manual
accurate and complete. However, Legrand | AV makes no claim
that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Legrand | AV
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Legrand | AV
assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
Chief® is a registered trademark of Legrand AV Inc.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the FSC1U mounting system
combined with the PACFCB does not exceed a total of 130
lbs (58.9 kg) or 65 lbs (29.5 kg) per display.
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this accessory outdoors.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all accessories are
properly assembled and installed using the instructions
provided.
CAUTION: To prevent possible injury to hands during
installation, use protective work gloves while installing cables
to mount.
--SAVE THESE INSTRUCTIONS--
WARNING: Failure to provide adequate structural strength
for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this accessory is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
accessory.
2
Page 3
Installation Instructions PACFCB
DIMENSIONS
127.76
5.03
355.60
14.00
623.57
24.55
3
Page 4
PACFCB Installation Instructions
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
4
Page 5
Installation Instructions PACFCB
1/8”
Hardware Kit
TOOLS REQUIRED FOR INSTALLATION
#2
5/32” (included)
1/8" (included)
PARTS
A (1)
[PACFCB accessory]
PARTS - DISPLAY INTERFACE
ER (2)
[Vertical bracket]
C (4)
#10-24 x 1/2"
Bag A
EA (4)
M4 x 12mm
Bag D
B (10)
[Cable tie]
Bag B
Bag E
E (1) - Display interface + hardware
EB (4)
M4 x 20mm
(See below)
D (1)
5/32"
Bag C
EC (4)
M4 x 25mm
Bag F
EQ (2)
[Horizontal bracket]
ED (4)
M5 x 12mm
Bag G
EG (4)
M6 x 12mm
Bag J
EJ (4)
M8 x 12mm
Bag M
[Nesting spacer]
Bag H
Bag K
EMA (8)
EN (8)
#10-24 x 1/2"
EE (4)
M5 x 20mm
EH (4)
M6 x 20mm
EK (4)
M8 x 20mm
[Universal spacer]
EF (4)
M5 x 25mm
Bag I
EI (4)
M6 x 25mm
Bag L
EL (4)
M8 x 30mm
EMB (4)
EP (1)
5
Page 6
PACFCB Installation Instructions
Assembly And Installation
Connecting to FSC1U
1. Use four #10-24 x 1/2" button head cap screws (C) to
secure PACFCB accessory to FCS1U outer frames. (See
Figure 1)
1
(A)
(C) x 4
Display Installation
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the FSC1U mounting system
combined with the PACFCB does not exceed a total of 130
lbs (58.9 kg) or 65 lbs (29.5 kg) per display.
WARNING: Make sure height is at the lowest possible
position.
4. Make sure latching flags are in "open" position.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! DO NOT substitute
hardware. Only use hardware provided or specified by
manufacturer.
5. Determine and mark the vertical center position between
the Left side Upper and Lower mounting holes in display.
(See Figure 3)
6. Determine and mark the vertical center position between
the Right side Upper and Lower mounting holes in display.
(See Figure 3)
Figure 1
2. Attach cables to top of FCS1U outer frames as shown in
FCS1U instructions but use middle of three holes to attach
cables to outer frames. (See Figure 1) and (See Figure 2)
middle hole
Figure 2
3. Tighten two turnbuckles (included with FCS1U) until cables
have little to no slack in them and use a level to make sure
the mount is level.
(ER) x 2
Mounting holes
3
6
Mounting Slots
Figure 3
7. Orient vertical mounting bracket (ER) so that mounting
holes are on top and mounting slots are on bottom. (See
Figure 3)
8. Align mounting holes in vertical mounting bracket (ER) with
upper and lower mounting holes in display.
9. Adjust vertical mounting bracket (ER) position until mark
made in Step 1 aligns with center mark in vertical mounting
bracket (ER).
6
Page 7
Installation Instructions PACFCB
10. Select correct screws, nesting spacers (if necessary) and
universal washers (if required) from the hardware bag (EAEM) and attach brackets to back of screen. (See Figure 5)
IMPORTANT ! : The M8 screws do NOT require a
washer. Use the universal washer (EMB) only with M4,
M5 and M6 screws.
NOTE: The nesting spacers (EMA) may be used separately, or
put two together in different configurations to create
different size spacers. (See Figure 4)
(Single) (Nested) (Stacked)
0.375
[9.5]
0.563
[14.3]
0.750
[19.1]
Figure 4
11. If the display has a recessed mounting surface, protrusions
or a power box, a spacer and longer mounting hardware
must be placed between the display and vertical mounting
bracket (ER). (See Figure 5)
12. Repeat Steps 5 through 8 for Right side vertical mounting
bracket using the same hole locations to align brackets
horizontally.
10
8
(EMA) x 4
(EMB) x 4
(ER)
(ER) x 2
Figure 5
(EA through EL)
x 4
7
Page 8
PACFCB Installation Instructions
13. Determine and mark the horizontal center position between
the Left and Right TOP mounting holes in display.
(See Figure 6)
14. Determine and mark the horizontal center position between
the Left and Right BOTTOM mounting holes in display. (See
Figure 6)
15. Orient upper horizontal mounting bracket (EQ) so that
flanges are facing towards display and resting in recessed
area of left and right vertical mounting brackets (ER). (See
Figure 6)
16. Adjust Upper horizontal mounting bracket (EQ) position
until center diamond in horizontal mounting bracket (EU)
aligns with mark made in Step 9, and mounting holes and
slots in horizontal mounting bracket (EQ) are aligned with
threaded holes in mounting tabs of left and right vertical
mounting brackets (ER). (See Figure 6) and (See Figure 7)
17. Use 1/8" hex key (EP) to secure upper horizontal mounting
bracket (EQ) to left and right vertical mounting brackets
(ER) using four button head flanged screws (EN). (See
Figure 7)
18. Repeat Steps 12 through 15 for lower horizontal mounting
bracket (EQ).
IMPORTANT ! : The orientation of, and mounting holes used,
when installing the lower horizontal mounting bracket must be
the same as the upper horizontal mounting bracket. Vertically
align upper and lower brackets by aligning holes or end of slots.
(See Figure 7)
IMPORTANT ! : Whenever possible install mounting
screws diagonally as shown in detail in Figure 7 below.
19. Install display with attached universal interface to mount
following the installation instructions provided with the
mount.
11
(EQ) x 2
(ER) x 2
Figure 6
12
Center Mark
(ER) x 2
15
(ER) x 2
15
14
(EN) x 8
(EQ) x 2
Figure 7
8
Page 9
Installation Instructions PACFCB
ADJUSTMENT
20. Lift display onto mount, carefully placing mounting buttons
into mounting locations on faceplate. (See Figure 8)
21. Slide locking plate over mounting buttons to secure display
to mount. (See Figure 8)
18
18
19
Figure 8
22. Tighten two turnbuckles (included with FCS1U) until cables
are tight and mount is level.
Adjustments
Plumb Adjustment
1. Loosen lower screws holding brackets together and adjust
plumb (up to 4°) as necessary to ensure displays are
perpendicular with the floor/ceiling. (See Figure 9)
2. Tighten lower screws holding brackets together when
desired plumb is reached. (See Figure 9)
(Side view)
1
2
3
PLUMB
Figure 9
9
Page 10
PACFCB Installation Instructions
10
Page 11
Installation Instructions PACFCB
11
Page 12
PACFCB Installation Instructions
8800-003173 Rev00
2019 Legrand | AV
www.legrandav.com
07/19
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Loading...