LEGRAND Chief PAC735 Installation Instructions Manual

Page 1
INSTALLATION INSTRUCTIONS
Secure Storage Cabinet
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
PAC735
Page 2
PAC735 Installation Instructions
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries (collectively “Legrand | AV”), intend to make this manual accurate and complete. However, Legrand | AV makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Legrand | AV makes no representation of warranty, expressed or implied, regarding the information contained herein. Legrand | AV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting system such as a video camera, CPU, screen, display, projector, etc.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all accessories are properly assembled and installed using the instructions provided.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! installer’s responsibility to make sure the combined weight of all equipment stored within the PAC735 does not exceed 40 lbs (18.14 kg).
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and repair.
WARNING: Do not use this accessory outdoors.
It is the
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the corresponding instructions.
--SAVE THESE INSTRUCTIONS--
2
Page 3
Installation Instructions PAC735
2.35
50.8
2.00
DOOR NOT SHOWN
SUITED TO 10-32 UNF CAGE
NUTS: McMASTER-CARR # 90680A127 OR EQUIVALENT
MAX RACK DEPTH = 20"
DIMENSIONS: [MILLIMETERS] INCHES
Tighten Fastener
Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations
Open-Ended Wrench
Llave de boca Gabelschlüssel Chave de bocas Chiave a punte aperte Steeksleutel Clé à fourche
By Hand
A mano Von Hand Com a mão A mano Met de hand À la main
Hex-Head Wrench
Llave de cabeza hexagonal Sechskantschlüssel Chave de cabeça sextavada Chiave esagonale Zeskantsleutel Clé à tête hexagonale
DIMENSIONS
LEGEND
3
Page 4
PAC735 Installation Instructions
1/2"
3/16" (included)
A (1)
B (1)
C (1)
D (1)
E (1)
[Front cross bar]
[Storage cabinet]
[Right wedge plate]
[Clamp bracket]
F (1)
[Rear cross bar]
G (4)
5/16-18 x 1"
H (2)
5/16-8 x 1/2"
J (12)
5/16-18"
L (2) [Key]
[Left wedge plate]
K (2) 1/4"
M (6) [Bumper]
N (1) 3/16"
TOOLS REQUIRED FOR INSTALLATION
PARTS
4
Page 5
Installation Instructions PAC735
3
2
(B)
(C)
(E)
(F)
(J) x 8
1
(H) x 2
(K) x 2
Cart
4
Base support
2
3
(M) x 6
ASSEMBLY AND INSTALLATION
Assemble Base Support (Cart Installation ONLY!)
NOTE: If installing PAC735 to a stand rather than a cart, the
base support is not needed as the PAC735 will sit directly on the base of the stand. Proceed to Mount Storage Cabinet section.
1. Place left wedge plate (B) and right wedge plate (C) on a flat surface with threaded bolts facing up. (See Figure 1)
2. Place front cross bar (E) and rear cross bar (F) on top of wedge plates and insert bolts through corresponding holes on cross bars. (See Figure 1)
3. Install eight 5/16-18" hex nuts (J) over each threaded bolt and tighten until cross bars are secured to wedge plates. (See Figure 1)
Figure 2
2. Slightly loosen (approximately three turns) the front button head cap screw on either side of the cart base. (See Figure )
NOTE: Only one screw should be loosened on only one side
of the cart base.
3. Add six bumpers (M) to top of base support. (See Figure 3)
4. Place base support inside legs of cart and push toward cart back. (See Figure )
Attach Base Support to Cart
1. Partially install two 5/16-18 x 1/2" square head cap screws (H) and two 1/4" flat washers (K) into side holes on wedge plates. DO NOT TIGHTEN! (See Figure 2)
Figure 1
NOTE: Screws should protrude approximately 1/8" beyond
wedge plate edge.
Figure 3
5
Page 6
PAC735 Installation Instructions
5
(H) x 2
6
Base support
Front cap of cart
7
(A)
Cart
(A)
(rear view)
(D)
(G) x 4
3
2
[Attaching to cart]
(rear view)
(A)
(D)
2
(G) x 4
3
[Attaching to stand]
5. Push base support back until it snaps in behind front cap of cart base. (See Figure 4)
6. Tighten button head cap screw on cart side which was loosened in Step 2. (See Figure 4)
7. Tighten two 5/16-18 x 1/2" square head cap screws (H) from Step 1 further into cart until base support is secured to cart. (See Figure 4)
3. Insert four 5/16-18 x 1" button head cap screws (G) through clamp bracket holes and into holes on back of storage cabinet (A). (See Figure 6) and (See Figure 7)
Figure 4
Mount Storage Cabinet
1. Place storage cabinet (A) on top of base support. (See Figure 5)
Figure 5
2. Place clamp bracket (D) around cart/stand and line up with holes on back of storage cabinet (A). (See Figure 6)
Figure 6
Figure 7
4. Open either door on accessory to install remaining four 5/16-18" hex nuts (J) onto four 5/16-18 x 1" button head cap screws (G) until accessory is fully secured to cart/stand. (See Figure 6)
5. Remove the protective layer from both the inside and outside of glass.
6. Up to three storage cabinets can be stacked vertically on top of each other per cart/stand. Repeat steps 1-4 for additional cabinets and use holes on top of cabinets to bolt cabinets together.
6
Page 7
Installation Instructions PAC735
Rack Installation (Optional)
1. Open windowed door.
2. Slide rack equipment (not included) into storage cabinet.
NOTE: Each storage cabinet supports 19" (483 mm) wide rack
mount equipment and has a capacity of 4 U.
3. Use #10-32 cage nuts (not included) to secure storage racks to storage cabinet.
7
Page 8
PAC735 Installation Instructions
8800-003114 Rev00 2019 Legrand | AV
www.legrandav.com
02/19
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852 F +31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099 F 852 2145 4477
Loading...