Page 1
I N S T A L L A T I O N I N S T R U C T I O N S
Outdoor Floor/Ceiling Concrete Mount
Single Ceiling
Dual Ceiling
Dual Floor
Single Floor
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
ODA330
Page 2
ODA330 Installation Instructions
DISCLAIMER
Legrand | AV and its affiliated corporations and subsidiaries
(collectively “Legrand | AV”), intend to make this manual
accurate and complete. However, Legrand | AV makes no claim
that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Legrand | AV
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Legrand | AV
assumes no responsibility for accuracy, completeness or
sufficiency of the information contained in this document.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
MOMENT: A MOMENT is a product of force and distance. It
is calculated by multiplying the force applied by install drop
length. See Dimensions drawings on Page 3 for further details.
all components attached to the ODA330 mounting system
cannot exceed 400 lbs.
WARNING: The weight capacity of the ODA mounting
systems may be LIMITED to the lowest weight capacity of
any component located between the ODA330 ceiling plate
and the flat panel display(s).
NOTE: "Moment" ratings have NOT been evaluated by UL.
WARNING: Exceeding the maximum moment can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the ODA330 mounting
system does not exceed a moment of 2000 ft-lbs. See table
below for specific column specifications.
COLUMN
MODEL
ODAC0203B 300 lbs (136 kg) 23 min - 36 max 2000
ODAC0304B 300 lbs (136 kg) 33 min - 48 max 2000
ODAC0405B 300 lbs (136 kg) 45 min - 60 max 2000
ODAC0506B 300 lbs (136 kg) 57 min - 72 max 2000
ODAC0708B 300 lbs (136 kg) 81 min - 96 max 2000
Weight
capacity
Moment
Length (IN)
(ML)
Max
Design
Moment
(FT-LBS)
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting systems
are properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. The structure must also be able to support three
times the maximum moment allowed. Reinforce the structure
as required before installing the mounting system.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
2
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Use this mounting system with other outdoor
products only.
WARNING: Always use two people or a mechanical lifting
device to safely lift and position equipment.
WARNING: Due to exposure to outdoor elements such as
strong wind gusts, heavy snow, hail, rain, etc., the mounting
system and its supporting structure must be inspected at
least once per year and immediately following any major
weather event. If evidence of excessive wear, deterioration or
any other unsafe condition is observed this product must be
taken out of service immediately!
IMPORTANT ! :
be mounted to a solid concrete floor or ceiling with a minimum
depth of 5.5" (140 mm) and a compressive strength of 5000 psi
for poured concrete or 6000 psi for pre-cast concrete. The
anchors must be embedded a minimum of 2 1/2" for poured
concrete or 2 1/4" for pre-cast concrete.
The ODA330
mounting system
is designed to
Page 3
Installation Instructions ODA330
NOTE: The ODA330 floor/ceiling plate is intended to be used with UL Listed ODAC Series columns (not included): ODAC0203,
ODAC0304, ODAC0405, ODAC0506, ODAC0708 and UL listed flat panel floor/ceiling mounts (not included): OLCM1U,
OXCM1U, OLCM2X1U, OLCB1U, OXCB1U, OLCB2X1U.
--SAVE THESE INSTRUCTIONS--
DIMENSIONS
3
Page 4
ODA330 Installation Instructions
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
4
Page 5
Installation Instructions ODA330
TOOLS REQUIRED FOR INSTALLATION
1/2" (12.7mm)
9/16" (16.6mm)
5/16" or 8mm
1/2" (12.7mm)
9/16" (16.6mm)
PARTS
A (1)
[Floor/ceiling plate]
+ Template on packaging insert (do NOT discard!)
F (4)
[Spacer]
B (2)
3/8-16
D (2)
3/8-16 x 4 1/4"
C (4)
1.0 x.41x.06
E (8)
3/8"
G (8)
M8 x 75mm
5
Page 6
ODA330 Installation Instructions
Assembly And Installation
1. Install eight 3/8" washers (E) onto eight M8 x 75mm anchors
(G). (See Figure 1)
(G) x 8
1
(E) x 8
Figure 1
2. Position template (on packaging insert) for floor/ceiling plate
(A) on floor or ceiling at desired installation location.
NOTE: If installing a two-plate mount (OLC2X1U/OLCB2X1U/
OXCM1U/OXCB1U), refer to dimensions drawings in
the installation instructions for that specific
configuration to determine distance between two
plates.
3. Mark two locations of outside keyhole-shaped holes. (See
Figure 2)
IMPORTANT ! : Holes must be drilled in exact locations
in order to be properly installed. Make sure hole locations
are marked precisely!
WARNING: Floor/Ceiling plate (A) weighs nearly 30 lbs
(13.6 kg). Use two people to install floor/ceiling plate to
ceiling. One person holds floor/ceiling plate in position while
the other person drills holes.
6. Lift floor/ceiling plate (A) up to M8 x 75m concrete anchors
(G), placing the two key-sized holes over the anchors. (See
Figure 3)
7. Turn floor/ceiling plate (A) so that anchors (G) are
positioned in small section of key-sized holes. (See Figure
3)
6
7
6
7
5
(G x 2)
4. Drill two 5/16" or 8mm holes with a depth of 2 7/8" at each
marked mounting hole location. (See Figure 2)
x
3
x
11
x x
11
x
x
11
x
9
4
5/16" or 8mm x 2 7/8"
x
11
x
x
9
x
3
x
Figure 3
8. Tighten two anchors (G). (See Figure 4)
9. Mark and drill two 5/16" or 8mm holes with a depth of 2 7/8"
for two remaining outside holes. (See Figure 2)
10. Install two M8 x 75mm concrete anchors (G) through
outside holes and into drilled holes. (See Figure 4)
8
x 2
(bottom view)
Figure 2
5. Partially install two M8 x 75mm concrete anchors (G) into
two drilled on opposite corners. (See Figure 3)
6
Figure 4
10
(G) x 2
Page 7
Installation Instructions ODA330
11. Mark and drill four 5/16" or 8mm holes with a depth of 2
7/8" in four of eight inside holes where remaining anchors
will be installed making sure the following rules are
followed. (See Figure 2) and (See Figure 5)
• ONE hole must be used adjacent to each of the
FOUR gussets.
• A total of TWO holes must be used for each HALF
of the plate.
Acceptable hole configuration
x
x
x
x
Unacceptable hole configuration
13. Insert pipe (not included) in to attach assembly (A) until
holes align for installation. (See Figure 7)
(A)
13
ODAC pipe (not included)
Figure 7
14. Use two 3/8-16 x 4 1/4" hex head bolts (D), four washers
(C), four spacers (F) and two 3/8-16 hex nuts (B). (See
Figure 8)
IMPORTANT ! : Make sure spacers (F) are properly
oriented to fit around pipe with the lines vertical.
x
x
x
x
Figure 5
12. Install four M8 x 75mm concrete anchors through four inside
holes drilled in Step 11. (See Figure 6)
12
(G) x 4
(C) x 4
lines vertical
14
(F) x 4
(B) x 2
spacers (F) positioned to
fit around pipe
(D) x 2
Figure 6
Figure 8
7
Page 8
ODA330 Installation Instructions
8800-003018 Rev01
2019 Legrand | AV
www.legrandav.com
03/19
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Loading...