Page 1
6000 Two-Piece Metal Raceway
INSTALLATION INSTRUCTIONS
Wiremold Electrical Systems conform to and should be installed and
properly grounded in compliance with requirements of the current
National Electrical Code, Canadian Electrical Code or codes administered by local authorities.
All electrical products may represent possible shock or fire hazard if
improperly installed or used. Wiremold electrical products are UL listed.
Made for interior use only and should be installed in conformance with
current local and/or the National Electrical Code.
UNSHIELDED SHIELDED
TWISTED PAIR TELEPHONE TWISTED
TYPE 24 AWG, 4-PAIR 24 AWG, NO. OF PAIRS COAXIAL TWINAXIAL PAIR FIBER OPTIC
TWO STRAND (DUPLEX)
CAT. 5 CAT. 3 2 3 4 25 RG58/U RG59/U RG62/U RG6/U 100 OHM TYPE 1 TYPE 2 TYPE 3 MULTIMODE, 62.5/125µm
O.D. inches 0.220 0.190 0.140 0.150 0.190 0.410 0.195 0.242 0.242 0.270 0.330 0.390 0.465 0.245 0.190
O.D. [mm] [5.6] [4.8] [3.6] [3.8] [4.8] [10.4] [5.0] [6.1] [6.1] [6.9] [8.4] [9.9] [11.8] [6.2] [4.8]
40% fill, divided 80 107 198 172 107 23 102 66 66 53 35 25 17 64 107
40% fill, undivided 161 217 399 348 217 46 206 133 133 107 71 51 36 139 217
6000 RACEWAY WIRE FILL CAPACITIES FOR DATA/COMMUNICATIONS
WITHOUT DEVICES WITH DEVICES (SURGE / GFCI)
TYPE AWG, THHN/THWN 2/0 1/0 1 2 4 6 8 10 12 14 2/0 1/0 1 2 4 6 8 10 12 14
O.D. inches .532 .486 .446 0.384 0.324 0.254 0.216 0.164 0.130 0.111 .532 .486 .446 0.384 0.324 0.254 0.216 0.164 0.130 0.111
O.D. [mm] 13.5 12.3 11.3 9.8 8.2 6.5 5.5 4.2 3.3 2.8 13.5 12.3 11.3 9.8 8.2 6.5 5.5 4.2 3.3 2.8
40% fill, divided 14 17 20 27 38 62 86 149 237 325 11 14 16 22 31 51 71 123 195 268
40% fill, undivided 28 34 40 54 76 125 173 300 475 652 22 26 31 43 60 98 135 235 373 512
• Use No.8 (5/16", 7.9mm head size) flat head fastener or equivalent to
mount base to surface.
• Utiliser une attache à tête plate de calibre 8 (tête de 7.9mm, 5/16" po.)
ou une fixation équivalente pour assujettir le tube guide-fils et les raccords à la surface de montage.
• Use un sujetador de cabeza plana No.8 (tamaño de cabeza: 7.9mm,
5/16" de pulgada) o su equivalente para unir la canalita y los accesorios a la superficie de montaje.
• Grounding: Use ground location when provided or install a suitable
ground lug, ring terminal or locknut and ground bushing.
• Mise à la terre: Utiliser l’emplacement de terre prévu ou poser le
matériel qui convient: patte de mise à la terre, cosse circulaire à oeil ou
écrou de blocage et manchon de terre.
• Conexión a tierra: Use un localizador de tierra cuando se proporcione
o instale una orejeta de tierra, anillo terminal o contratuerca y cojinetes
de tierra apropiados.
6000 RACEWAY WIRE FILL CAPACITIES FOR POWER
18"
[45.7cm]
6000B-10660B 640C 4000WC6000C 6000WC
6000DA / 6001DA
6001
1 2 3
6006
6007C-2 / 6007C-1
1 2 3
6008A
1
4
2 3
60" max
[152cm]
Page 2
2
3
4
1
6012TX
1
2
1
2
6011TX
6011TX
6001TX
1
2
3
6012TX
Wire Fill: 1/2 of values shown on page 1.
Adjust
screws if
needed.
Adjust
screws if
needed.
Wire Fill: 1/2 of values shown on page 1.
45°
Wire Fill: 1/2 of values shown on page 1.
Wire Fill: 1/2 of values shown on page 1.
6010B
45°
6014A
6017TX
2
3
1
6017TX
2
3
1
2
1
6017TX
6074A
6074
6086
1
6046KD
2 3 4 5
Wire Capacity Size AWG
Type 2/0 1/0 #1 #2 #3 #4 #6 #8 #10 #12 #14
THHN, THWN 14 17 20 28 33 39 64 88 153 244 334
41401R1 499
The Wiremold Company
60 Woodlawn Street • West Hartford, CT 06110
1-800-621-0049 • Fax 860-232-2062
©1999 The Wiremold Company
1/2"
12.7mm
2"
51mm
1/2"
12.7mm
6000DA
6000DA
6000DA
1"
25mm
2 3/4"
70mm
2 1/2"
64mm
Loading...