PRODUCT INFORMATION PACKET
Model No: LM34162
Catalog No: LM34162
1 HP General Purpose Motor, 3 phase, 1200 RPM, 230/460 V, 56C Frame, TEFC
Three Phase TEFC Motors
Regal and Leeson are trademarks of Regal Beloit Corporation or one of its affiliated companies.
©2019 Regal Beloit Corporation, All Rights Reserved. MC017097E
1 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 61 of 6
Product Information Packet: Model No: LM34162, Catalog No:LM34162 1 HP General Purpose Motor, 3 phase, 1200 RPM, 230/460 V, 56C Frame,
TEFC
Nameplate Specifications
Output HP 1 Hp Output KW 0.75 kW
Frequency 60 Hz Voltage 230/460 V
Current 3.8/1.9 A Speed 1140 rpm
Service Factor 1.15 Phase 3
Efficiency 82.5 % Power Factor 60
Duty Continuous Insulation Class B
Design Code B KVA Code L
Frame 56C Enclosure Totally Enclosed Fan Cooled
Thermal Protection No Ambient Temperature 40 °C
Drive End Bearing Size 6205 Opp Drive End Bearing Size 6203
UL Recognized CSA Y
CE Y IP Code 43
Technical Specifications
Electrical Type Squirrel Cage Induction Run Starting Method Across The Line
Poles 6 Rotation Reversible
Resistance Main 0 Ohms Mounting Round
Motor Orientation Horizontal Drive End Bearing Ball
Opp Drive End Bearing Ball Frame Material Rolled Steel
Shaft Type NEMA 56 Overall Length 15.15 in
Frame Length 9.65 in Shaft Diameter 0.625 in
Shaft Extension 2.06 in Assembly/Box Mounting F1/F2 CAPABLE
This is an uncontrolled document once printed or downloaded and is subject to change without notice. Date Created:01/11/2019
2 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 62 of 6
4 21
4 21
3
3
Uncontrolled Copy
15.15
384.92
D
D
.25
.12
6.35
3.05
C
C
3.14
79.76
NAMEPLATE READ FROM CONDUIT
BOX SIDE OF MOTOR.
13.09
332.49
9.65
245.11
5.38
7.36
187.05
136.76
4.48
113.87
2.06
52.44
.16
4.18
2.53
.10
1.88
47.75
15.8750
15.8623
.6250
.6245
.19X.19X1.38
KEY
114.300
114.224
[27.69]
KNOCKOUTS
4.500
4.497
[22.35]
KNOCKOUTS
1.09
2X
3X
.88
9.07
230.29
D
D
45°
45°
6.56
166.58
7.14
181.39
C
C
3/8-16 UNC-2B
.56 MIN. FULL THD
8.81
223.71
B
B
A
A
DRAWING REVISION REVISION BY DATE
DRAWING REVISION REVISION BY DATE
B D.SURYAWANSHI 08/24/2018
B D.SURYAWANSHI 08/24/2018
ECO
ECO
ECO-0097684 PVR 08/24/2018
ECO-0097684 PVR 08/24/2018
ECO DESCRIPTION
ECO DESCRIPTION
PROPRIETARY AND CONFIDENTIAL INFORMATION - THIS DOCUMENT IS THE PROPERTY OF
PROPRIETARY AND CONFIDENTIAL INFORMATION - THIS DOCUMENT IS THE PROPERTY OF
INFORMATION. ANY PERSON, CORPORATION OR OTHER FIRM RECEIVING IT IS DEEMED,
INFORMATION. ANY PERSON, CORPORATION OR OTHER FIRM RECEIVING IT IS DEEMED,
BY RECEIVING IT, TO AGREE THAT IT, AND/OR ANY PART OF IT, SHALL NOT BE DISCLOSED
BY RECEIVING IT, TO AGREE THAT IT, AND/OR ANY PART OF IT, SHALL NOT BE DISCLOSED
TO ANY PERSON, CORPORATION OR OTHER ENTITY, DUPLICATED, AND/OR USED, EXCEPT
TO ANY PERSON, CORPORATION OR OTHER ENTITY, DUPLICATED, AND/OR USED, EXCEPT
AS EXPRESSLY APPROVED IN WRITING IN ADVANCE BY OWNER. THIS DOCUMENT SHALL
AS EXPRESSLY APPROVED IN WRITING IN ADVANCE BY OWNER. THIS DOCUMENT SHALL
4 21
4 21
3
3
APPROVED BY DATE
APPROVED BY DATE
UPDATED SHAFT EXTENSION
UPDATED SHAFT EXTENSION
COPYRIGHT REGAL BELOIT AMERICA, INC. ALL RIGHTS RESERVED.
COPYRIGHT REGAL BELOIT AMERICA, INC. ALL RIGHTS RESERVED.
REGAL BE LOIT AM ERICA, INC. (" OWNER") A ND CO NTAINS OWNE R'S PROPRIE TARY
REGAL BE LOIT AM ERICA, INC. (" OWNER") A ND CO NTAINS OWNE R'S PROPRIE TARY
BE RETURNED TO O WNER UPON REQ UEST. IT M A Y BE SUBJ E CT TO CERTAIN
BE RETURNED TO O WNER UPON REQ UEST. IT M A Y BE SUBJ E CT TO CERTAIN
RESTRICTIONS UNDER APPLICABLE EXPORT CONTROL LAWS AND REGULATIONS.
RESTRICTIONS UNDER APPLICABLE EXPORT CONTROL LAWS AND REGULATIONS.
4 HOLES
TOLERANCES UNLESS
TOLERANCES UNLESS
OTHERWISE SPECIFIED:
OTHERWISE SPECIFIED:
DEC. INCH mm ANGLE
DEC. INCH mm ANGLE
.X 0.1 [ 2.5] 0.5
.X 0.1 [ 2.5] 0.5
.XX 0.02 [ 0.51]
.XX 0.02 [ 0.51]
.XXX 0.005 [ 0.127]
.XXX 0.005 [ 0.127]
.XXXX 0.0005 [ 0.0127]
.XXXX 0.0005 [ 0.0127]
REMOVE BURRS & BREAK SHARP
REMOVE BURRS & BREAK SHARP
EDGES: .003/ .015 [ . 076/ . 381] X 45
EDGES: .003/ .015 [ . 076/ . 381] X 45
CORNER FILLETS: R.02 [.51]
CORNER FILLETS: R.02 [.51]
MACHINED SURFACES:
MACHINED SURFACES:
INCH mm
INCH mm
mm SHOWN IN [BRACKETS]
mm SHOWN IN [BRACKETS]
125
125
3 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 63 of 6
3.2
3.2
DRAWN BY
DRAWN BY
E.VILLA
E.VILLA
DATE
DATE
03-03-2017
03-03-2017
APPROVED BY
APPROVED BY
A.ARREOLA
A.ARREOLA
DATE
DATE
03-03-2017
03-03-2017
REFERENCE
REFERENCE
THIRD ANGLE
THIRD ANGLE
PROJECTION
PROJECTION
TM
TM
Regal Beloit America, Inc.
Regal Beloit America, Inc.
DESCRIPT ION
DESCRIPT ION
MATERIAL
MATERIAL
DRAWING NUMB ER
DRAWING NUMB ER
SIZE
SIZE
C OL56100240-001
C OL56100240-001
OUTLINE
OUTLINE
56H FR,TEFC, C-FACE
56H FR,TEFC, C-FACE
PROCESS/FINISH
PROCESS/FINISH
SHEET
SHEET
1 OF1
1 OF1
B
B
A
A
Regal Beloit America, Inc.
TM
COPYRIGHT REGAL BELOIT AMERICA, INC. ALL RIGHTS RESERVED.
PROPRIETARY AND CONFIDENTIAL INFORMATI ON - THIS DOCUMENT IS THE PROPERTY OF
REGAL BELOIT AMERICA, INC. ("OWNER") AND CONTAINS OWNER'S PROPRIETARY
INFORMATION. ANY PERSON, CORPORATION OR OTHE R FIRM RECEIVING IT IS DEEMED,
BY RECEIVING IT, TO AGREE THAT IT, AND/OR ANY PART OF IT, SHALL NOT BE DISCLOSED
TO ANY PERSON, CORPORATION OR OTHER ENTI TY, DUPLICATED, AND/OR USED, EXCEPT
AS EXPRESSLY APPROVED IN WRITING IN ADVANCE BY OWNER. THIS DOCUMENT SHALL
BE RETURNED TO OWNER UPON REQUEST. IT MAY BE SUBJECT TO CERTAIN
RESTRICTIONS UNDER APPLICABLE EXPORT CONTROL LAWS AND REGULATIONS.
TOLERANCES UNLESS
OTHERWISE SPECIFIED:
DEC.
INCH mm ANG LE
.X 0.1 [ 2.5] 0.5
.XX 0.01 [ 0.25]
XXX 0.005 [ 0.127]
.XXXX 0.0005 [ 0.0127]
REMOVE BURRS & BREAK SHARP
EDGES: .003/.015 [.076/.381]
CORNER FILLETS: .02 [.51]
MACHINED SURFACES:
125 3.2
INCH mm
mm SHOWN IN [BRACKETS]
12
43
A
B
2
43
1
A
B
ECO DESCRIPTION
DATEAPPROVED BY
DATEREVISION BY
ECO
DRAWING REVISION
REFERENCE
MATERIAL
SHEET
DRAWING NUMBERSIZE
DESCRIPTION
THIRD ANGLE
PROJECTION
DRAWN BY
DATE
DATE
APPROVED BY
PROCESS/FINISH
B
1 OF 1
CDTD127
G. RODRIGUE Z
12-01-2017
J. A. MORENO
12-01-2017
D SHESHI 01/11/2019
ECO-0159881 CD 01/11/2019
ADDED DD10199-001
CONN DIAGRAM-EXTERNAL
CDTD103
VIEW OF TERMINAL END
CCW LOW VOLTAGE
CCW HIGH VOLTAGE
NOTE:
TO REVERSE ROTATION, INTERCHANGE ANY TWO LINE 1.
CONNECTIONS TO L1, L2, OR L3.
2. CONNECTION DIAGRAM-NAMEPLATE
DD10123-001 - CCWLE
DD10199-001 - CWLE
L3
T3 BLUE
L1
RED T1
L2
BROWN T4
T7 PURPLE
T5 ORANGE
T2
WHT
T8
TAN
T6
BLK
T9
PINK
T3 BLUE
L3
T8 TAN
T6 BLACK
T5 ORANGE
T1 RED
T4 BROWN
T9 PINK
T7 PURPLE
T2 WHITE
T3 BLUE
BLACK T6
PINK T9
T2
WHT
T1 RED
BROWN T4
T7 PURPLE
T8 TAN
T5 ORN
L2
L1
001
002
Regal Beloit America, Inc.
TM
COPYRIGHT REGAL BELOIT AMERICA, INC. ALL RIGHTS RESERVED.
PROPRIETARY AND CONFIDENTIAL INFORMATI ON - THIS DOCUMENT IS THE PROPERTY OF
REGAL BELOIT AMERICA, INC. ("OWNER") AND CONTAINS OWNER'S PROPRIETARY
INFORMATION. ANY PERSON, CORPORATION OR OTHE R FIRM RECEIVING IT IS DEEMED,
BY RECEIVING IT, TO AGREE THAT IT, AND/OR ANY PART OF IT, SHALL NOT BE DISCLOSED
TO ANY PERSON, CORPORATION OR OTHER ENTI TY, DUPLICATED, AND/OR USED, EXCEPT
AS EXPRESSLY APPROVED IN WRITING IN ADVANCE BY OWNER. THIS DOCUMENT SHALL
BE RETURNED TO OWNER UPON REQUEST. IT MAY BE SUBJECT TO CERTAIN
RESTRICTIONS UNDER APPLICABLE EXPORT CONTROL LAWS AND REGULATIONS.
TOLERANCES UNLESS
OTHERWISE SPECIFIED:
DEC.
INCH mm ANG LE
.X 0.1 [ 2.5] 0.5
.XX 0.01 [ 0.25]
XXX 0.005 [ 0.127]
.XXXX 0.0005 [ 0.0127]
REMOVE BURRS & BREAK SHARP
EDGES: .003/.015 [.076/.381]
CORNER FILLETS: .02 [.51]
MACHINED SURFACES:
125 3.2
INCH mm
mm SHOWN IN [BRACKETS]
12
43
A
B
2
43
1
A
B
ECO DESCRIPTION
DATEAPPROVED BY
DATEREVISION BY
ECO
DRAWING REVISION
REFERENCE
MATERIAL
SHEET
DRAWING NUMBERSIZE
DESCRIPTION
THIRD ANGLE
PROJECTION
DRAWN BY
DATE
DATE
APPROVED BY
PROCESS/FINISH
B
1 OF 1
CDTD127
G. RODRIGUE Z
12-01-2017
J. A. MORENO
12-01-2017
D SHESHI 01/11/2019
ECO-0159881 CD 01/11/2019
ADDED DD10199-001
CONN DIAGRAM-EXTERNAL
CDTD103
VIEW OF TERMINAL END
CCW LOW VOLTAGE
CCW HIGH VOLTAGE
NOTE:
TO REVERSE ROTATION, INTERCHANGE ANY TWO LINE 1.
CONNECTIONS TO L1, L2, OR L3.
2. CONNECTION DIAGRAM-NAMEPLATE
DD10123-001 - CCWLE
DD10199-001 - CWLE
L3
T3 BLUE
L1
RED T1
L2
BROWN T4
T7 PURPLE
T5 ORANGE
T2
WHT
T8
TAN
T6
BLK
T9
PINK
T3 BLUE
L3
T8 TAN
T6 BLACK
T5 ORANGE
T1 RED
T4 BROWN
T9 PINK
T7 PURPLE
T2 WHITE
T3 BLUE
BLACK T6
PINK T9
T2
WHT
T1 RED
BROWN T4
T7 PURPLE
T8 TAN
T5 ORN
L2
L1
001
002
Uncontrolled Copy
4 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 64 of 6
Uncontrolled Copy
5 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 65 of 6
HZ
11/5/2018
Uncontrolled Copy
LEESON ELECTRIC CORPORATION
TYPICAL PERFORMANCE CURVE for AC MOTOR
Curve at 460 Volts HP 1.00
60 HZ
Model No LM34162 1 HP VOLTS 230/460
3
Catalog No LM34162A
60 70 80 90 100
EFF
60 70 80 90 100
PF
HP
60 RPM 1140
Eff −
−
−−
PF −
−
−−
HP −
−
−−
RPM −
−
−−
KW −
−
−−
Amps −
−
−−
1.2 1.4 1.6 1.8 2
RPM
1.2 1.4 1.6 1.8 2
1210 1220 1230 1240 1250
KW
60 70 80 90 10060 70 80 90 1001.2 1.4 1.6 1.8 21210 1220 1230 1240 12501.2 1.4 1.6 1.8 23 3.5 4 4.5 5
PF
HP
KW
EFF
RPM
AMPS
0 10 20 30 40 50
0 10 20 30 40 50
0 1 2 3 4 5 6
0 0.2 0.4 0.6 0.8 1
0 1 2 3 4 5 6
0 1 2 3 4 5 6
0 0.2 0.4 0.6 0.8 1
1150 1160 1170 1180 1190 1200
0 1 2 3 4 5 6
0 10 20 30 40 50
0 10 20 30 40 50
0 0.2 0.4 0.6 0.8 1
0 0.2 0.4 0.6 0.8 1
0 0.5 1 1.5 2 2.5
1150 1160 1170 1180 1190 1200
0 1 2 3 4 5 6
Torque
0 1 2 3 4 5 6
0 1 2 3 4 5 6
0 1 2 3 4 5 6
0 1 2 3 4 5 6
0 1 2 3 4 5 6
0 1 2 3 4 5 6
Torque
Torque
Torque
Torque
FL TORQUE 4.5 Lb.Ft FL AMPS 3.8/1.9
BD TORQUE 18.4 Lb.Ft PU TORQUE 11.8 Lb.Ft
LR TORQUE 13.1 Lb.Ft LR AMPS 11.8
WINDING ZT6139-3 Date
Torque
Torque
Torque
Torque
Torque
Torque
Torque in Lb.Ft
6 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 66 of 6
Loading...