Advanced Baby Monitor
Instruction manual
Power
Lig
h
t
Pag
e
+
Digital Baby Monitor
Play /
Stop
Music
Volume
_
Digital Baby Monitor
Tal k
M
e
n
u
O
K
TM
L
i
n
k
Leapfrog Advanced BM.indd 1Leapfrog Advanced BM.indd 1 26/6/08 09:10:2226/6/08 09:10:22
2
Advanced Baby Monitor
Thank you for purchasing this advanced baby monitor. Please read the
instructions and warnings carefully before use to ensure the safe and
satisfactory operation of this product.
Important safety information . . . 3
Your advanced baby monitor . . . 4
Instructions for use . . . . . . . . . . . 5
Check the package contents . . 5
Setting up the parent unit . . . . 5
Setting up the baby unit . . . . . 6
Volume . . . . . . . . . . . . . . . . . . . 6
Using your advanced baby monitor
7
Battery low . . . . . . . . . . . . . . . 7
Language . . . . . . . . . . . . . . . . . 7
Setting the clock . . . . . . . . . . . 7
Baby alert . . . . . . . . . . . . . . . . 8
Lullaby . . . . . . . . . . . . . . . . . . . 9
Temperature . . . . . . . . . . . . . 10
Centigrade to Fahrenheit . . . 11
Parent to parent paging . . . . . 11
Talk to your baby . . . . . . . . . 11
Night-light . . . . . . . . . . . . . . . 12
Torch . . . . . . . . . . . . . . . . . . . 12
Baby feed timer . . . . . . . . . . . 12
Feed alarm . . . . . . . . . . . . . . . 13
Sound sensitivity . . . . . . . . . . 14
Simple solutions . . . . . . . . . . . . 15
General information . . . . . . . . . 16
Changing the batteries . . . . . 16
Guarantee . . . . . . . . . . . . . . . 17
Weee Directive . . . . . . . . . . . 17
Contents
Leapfrog Advanced BM.indd 2Leapfrog Advanced BM.indd 2 26/6/08 09:10:2626/6/08 09:10:26
3
Keep the product and all its
parts out of reach of small
children.
Batteries are small objects.
Replacement of the batteries
must be done by adults.
Keep it dry. Avoid exposure
to precipitation, humidity and
liquids which could all affect
the product circuitry.
Do NOT leave it in high
temperatures as electronic
devices and plastic parts may
warp in heat.
Do NOT leave it in low
temperatures as moisture can
form inside the product, which
may damage the circuit board.
Do NOT use harsh
chemicals, cleaning solvents
or detergents to clean the
product. Wipe with a damp
(not wet) soft cloth to clean.
•
•
•
•
•
•
Do NOT attempt to open
the product. Unauthorised
handling of the device may
damage it and will void your
warranty.
Only use the power supply
that came with the product.
Using an unauthorised
power supply will invalidate
your guarantee and may
irrecoverably damage the
product.
Radio signals transmitted
between the Parent and Baby
unit may cause interference to
hearing aids.
Do NOT use your baby
monitor near emergency/
intensive care medical
equipment, if you have a
pacemaker fi tted or during an
electrical storm.
•
•
•
•
Important safety information
Your advanced baby monitor should be treated with care. The
information below has been provided in the interest of safety and will
help you to enjoy this product and the benefi ts it brings for many years.
Use of this equipment is no substitute for personal attention and
supervision of a child.
Leapfrog Advanced BM.indd 3Leapfrog Advanced BM.indd 3 26/6/08 09:10:2626/6/08 09:10:26
4
Your advanced baby monitor
Power on/off
Press and release to power on
Press and hold to power off
Display
Lullabies
Page
Press and hold for
2 seconds to ‘Page’
the Parent unit
Night-light on/off
Volume up
Microphone
Soft night-light
Speaker
Volume down
Temperature sensor
Play/Stop lullabies
Battery compartment for non-rechargeable
batteries (not supplied)
Power
Lig
h
t
Pag
e
+
Digital Baby Monitor
Play /
Stop
Music
Volume
_
Display
Link LED
Noise indication LEDs
OK
Ta lk
Volume up/Move up
(in the menu)
Menu
Microphone
To r c h
Press and hold
Speaker
Volume down/Move down
(in the menu)
Power on/off
Press and release to power on
Press and hold to power off
Digital Baby Monitor
Tal k
M
e
n
u
O
K
TM
L
i
n
k
Leapfrog Advanced BM.indd 4Leapfrog Advanced BM.indd 4 26/6/08 09:10:2726/6/08 09:10:27
5
Instructions for use
Check the package
contents
The package contains:
1 Parent unit (receiver) with
belt clip
1 charger pod with fi xed
mains adaptor
2 x 800mAh NiMH
rechargeable batteries
1 Baby unit (sender)
1 mains adaptor
1 travel bag
1 instruction manual
Setting up
At the parent unit
1. Remove the battery cover on
the back of the parent unit with a
crosshead screwdriver.
Torc h
2. Insert the 2 x AAA 1.2V
800mAh Nickel Metal Hydride
rechargeable batteries provided,
taking care to note the ‘+’ and
‘-’ markings and position the
batteries the correct way around.
Replace the battery cover and
re-tighten the screw.
•
•
•
•
•
•
•
3. Fit the belt clip by sliding into
place until it clicks home.
Torc h
4. Plug the charger pod mains
adaptor into a mains power
socket and switch on.
5. Place the parent unit in the
charger pod and charge for a
minimum of 13 hours before fi rst
use or if it has not been used for a
long time.
The red LED on the charger pod
will light up to confi rm that the
parent unit is charging and will
remain on whilst the parent unit is
in the charger pod.
Note: The parent unit cannot
be used without rechargeable
batteries, even if it is placed in the
charger.
6. Press and release the ‘Power’
key on the side of the parent unit
to switch it on.
Leapfrog Advanced BM.indd 5Leapfrog Advanced BM.indd 5 26/6/08 09:10:2926/6/08 09:10:29
6
Setting up
At the baby unit
1. Your baby unit does not require
batteries to function but we
recommend that you install them.
Should there be a power cut,
your baby unit can then switch
to the backup (non-rechargeable)
battery power.
2. Remove the battery cover on
the bottom of the baby unit with
a crosshead screwdriver. Insert 3
x AA alkaline batteries, taking care
to note the ‘+’ and ‘-’ markings
and position the batteries the
correct way around. Replace the
battery cover and re-tighten using
the crosshead screwdriver.
Note: Do NOT use rechargeable
batteries in the baby unit.
3. Connect the power lead to the
bottom of the baby unit and plug
the mains adaptor into a mains
power socket and switch on.
4. Press and release the ‘Power’
key to switch on.
Note: The baby unit should be
placed about 1 m to 1.5 m away
from the baby’s cot or playpen on
a fl at and stable surface. Never
place the baby unit inside the cot,
bed or playpen. Make sure the
unit, cords and mains adaptor
are out of reach of the baby and
other young children.
Never place either the parent or
baby unit on antique or polished
surfaces.
When you have set up your
advanced baby monitor, you will
be able to hear the sounds in your
baby’s room through the speaker
on the parent unit. The green and
red noise indication LEDs will
also rise and fall with the sound
volume level. The more lights you
see, the louder the noise, with the
red lights indicating the loudest
noise level.
Note: If the connection between
the parent and baby unit is broken
at any time, the ‘Link’ light on
the parent unit will fl ash and the
green and red noise indication
LEDs will no longer react to any
sounds. To re-establish the link,
please refer to page 15.
Volume
You can adjust the volume of the
sounds that you can hear through
the parent unit by using the
‘Volume + / -’ keys on the side
of the parent unit. This will not
affect the sensitivity of your baby
monitor, only the volume of the
sounds that you can hear.
Leapfrog Advanced BM.indd 6Leapfrog Advanced BM.indd 6 26/6/08 09:10:3026/6/08 09:10:30
7
Battery charge indicator
and battery low warning
The parent unit can operate for
a maximum of 10 hours when it
is out of the charger pod but this
depends on the level of charge
in the batteries and if any of the
other parent unit functions have
been used such as the ‘Torch’ or
‘Talk’ features.
The battery charge level is indicated
by the battery icon on the parent
unit display. If the battery level is
low, the battery icon will begin to
fl ash and you will hear a warning
‘beep’. You should return your
parent unit to the charger pod to
recharge the batteries. You can
still use your parent unit whilst it is
charging in the charger pod. (Check
that the red charging LED lights up
on the charger pod).
Language
Your advanced baby monitor can
display information in six different
languages: English, German, Spanish,
French, Italian and Russian.
To change the display language:
1. Press the ‘Menu’ key and
then use the ‘Up/Down’ keys on
the side of the parent unit until
‘Language’ is displayed. Press
the ‘OK’ key.
2. Use the ‘Up/Down’ keys to scroll
to your chosen language and press
the ‘OK’ key to confi rm. ‘Saved’
will be displayed briefl y. Your chosen
language will now be set.
Clock
The parent unit can display the
current date and time in either 12
or 24 hour clock (the default setting
is 24 hour clock). You will need to
set the clock before you can use
the baby feed timer feature.
To set the time:
1. Press the ‘Menu’ key and then
use the ‘Up/Down’ keys to scroll
to ‘Clock’. Press the ‘OK’ key.
2. ‘Set time’ is displayed. Press
the ‘OK’ key.
3. ‘Ye ar ’ is displayed. Use the
‘Up/Down’ keys to scroll to the
correct year. Press the ‘OK’ key.
4. ‘Month’ is displayed. Use the
‘Up/Down’ keys to scroll to the
correct month. Press the ‘OK’ key.
5. ‘Day’ is displayed. Use the
‘Up/Down’ keys to scroll to the
correct day. Press the ‘OK’ key.
6. ‘Hour’ is displayed. Use the
‘Up/Down’ keys to scroll to the
correct hour. Press the ‘OK’ key.
Using your advanced baby monitor
Leapfrog Advanced BM.indd 7Leapfrog Advanced BM.indd 7 26/6/08 09:10:3126/6/08 09:10:31
8
7. ‘Minute’ is displayed. Use the
‘Up/Down’ keys to scroll to the
correct minute. Press the ‘OK’ key.
You will hear a confi rmation ‘beep’
and ‘Saved’ will be briefl y displayed.
The time and date will now be
displayed on the parent unit.
To set 12 or 24 hour clock:
1. Press the ‘Menu’ key and then
use the ‘Up/Down’ keys to scroll
to ‘Clock’. Press the ‘OK’ key.
2. Use the ‘Up/Down’ keys to
scroll to ‘Hour Format’. Press
the ‘OK’ key.
3. ‘12Hrs?’ will be displayed when
24 hour clock is already set. Press
the ‘OK’ key to change to 12
hour clock or the ‘Menu’ key to
exit without changing the setting.
If 12 hour clock is set, ‘24Hrs?’
will be displayed for this step.
Press the ‘OK’ key to change to
24 hour clock.
Note: When 12 hour clock is
set a small ‘a’ will be displayed for
‘AM’ and a small ‘p’ for ‘PM’.
Baby alert
You can set your parent unit to
give a warning ‘beep’ if the noise
levels in your baby’s room activate
the red lights on the parent unit.
This is a really useful feature if
the volume of your parent unit
is turned down and you are just
using the noise indication lights to
monitor the noise levels in your
baby’s room.
At the parent unit:
1. Press the ‘Menu’ key and then
use the ‘Up/Down’ keys to scroll
to ‘Sound Alert’. Press the
‘OK’ key.
2. ‘On?’ will be displayed. Press
the ‘OK’ key to turn the alert on
or the ‘Menu’ key to exit without
changing the setting. You will hear
a confi rmation ‘beep’ and ‘Saved’
will be briefl y displayed.
To turn the baby alert off, follow
the steps above. ‘Off?’ will be
displayed. Press the ‘OK’ key. You
will hear a confi rmation ‘beep’ and
‘Saved’ will be briefl y displayed.
To change the alert tone volume:
1. Press the ‘Menu’ key and then
use the ‘Up/Down’ keys to scroll
to ‘Sound Alert’. Press the
‘OK’ key.
Leapfrog Advanced BM.indd 8Leapfrog Advanced BM.indd 8 26/6/08 09:10:3126/6/08 09:10:31
9
2. Use the ‘Up/Down’ keys to
scroll to ‘Vo lume ’. Press the
‘OK’ key.
3. Use the ‘Up/Down’ keys to
change the volume level. Press
the ‘OK’ key. You will hear a
confi rmation ‘beep’ and ‘Saved’
will be briefl y displayed.
Note: 5 blocks on the display =
maximum volume.
Lullaby
You can soothe your baby to sleep
with a gentle lullaby from the
baby unit. There are 5 lullabies
to choose from or you can select
to ‘Play All’. You can switch the
lullabies on and off from both the
parent and baby unit and they will
play for 15 minutes.
To select and start a lullaby at the
baby unit:
1. Press the ‘Music’ key. The
backlight will turn on and the
name of the lullaby will be
displayed.
2. Continue to press the ‘Music’
key to scroll to the lullaby that you
would like to play or select ‘Play
All?’.
3. Press the ‘Play/Stop’ key to
stop and start the lullaby.
To select and start a lullaby at the
parent unit:
1. Press the ‘Menu’ key and then
use the ‘Up/Down’ keys to scroll
to ‘Lullaby’. Press the ‘OK’ key.
2. ‘Play?’ is displayed. Press the
‘OK’ key to play the lullaby or use
the ‘Up/Down’ keys to scroll to
‘Select New’ and press the
‘OK’ key.
3. The name of the current lullaby
is displayed. Use the ‘Up/Down’
keys to scroll to the lullaby that
you would like to play or select
‘Play All?’. Press the ‘OK’ key.
You will hear a confi rmation
‘beep’ and ‘Saved’ will be briefl y
displayed.
4. ‘Lullaby’ is displayed. Press the
‘OK’ key twice.
The lullaby will begin to play on
the baby unit.
To stop playing the lullaby, press
the ‘OK’ key twice when you are
in ‘Lullaby’ mode.
Note: The lullabies will stop
playing automatically after 15
minutes.
Leapfrog Advanced BM.indd 9Leapfrog Advanced BM.indd 9 26/6/08 09:10:3126/6/08 09:10:31
10
Temperature
It is very important for your baby’s
health to ensure that he/she is
kept at a safe temperature. This
includes the room temperature,
baby’s temperature, baby clothing
and bedding (contact your local
health authority to ensure that
you are aware of the current
guidelines). Your baby monitor
can help by displaying the current
room temperature on the baby
unit and parent unit. It can even be
set to alert you if it falls outside of
a set range.
Changing the temperature
range
You can set the upper and lower
temperature limits of your baby
monitor so that you are alerted
if the temperature in the baby’s
room goes above or below your
pre-set range. The temperature
displayed on the parent unit will
fl ash and an alert, if set, will sound.
At the parent unit:
1. Press the ‘Menu’ key and then
use the ‘Up/Down’ keys to scroll
to ‘Temperature’. Press the
‘OK’ key.
2. Use the ‘Up/Down’ keys to
scroll to ‘Set Range’ and press
the ‘OK’ key. The current upper
temperature range is displayed,
e.g., ‘Up limit xx’.
3. Use the ‘Up/Down’ keys to
change the upper temperature
level. Press the ‘OK’ key. You will
hear a confi rmation ‘beep’ and
‘Saved’ will be briefl y displayed.
4. The lower range limit is now
displayed e.g., ‘Low limit xx’.
5. Use the ‘Up/Down’ keys to
change the lower temperature
level. Press the ‘OK’ key. You will
hear a confi rmation ‘beep’ and
‘Saved’ will be briefl y displayed.
Setting the temperature alert
You can set your parent unit to
give an additional ‘double beep’
warning to alert you that the
temperature has moved outside
of the pre-set range.
At the parent unit:
1. Press the ‘Menu’ key and then
use the ‘Up/Down’ keys to scroll
to ‘Temperature’. Press the
‘OK’ key.
2. Use the ‘Up/Down’ keys to
scroll to ‘Temp Alert’ and press
the ‘OK’ key.
3. ‘On?’ will be displayed. Press
the ‘OK’ key to turn the alert on
or the ‘Menu’ key to exit without
changing the setting. You will hear
a confi rmation ‘beep’ and ‘Saved’
will be briefl y displayed.
Leapfrog Advanced BM.indd 10Leapfrog Advanced BM.indd 10 26/6/08 09:10:3226/6/08 09:10:32
11
To turn the temperature alert
off, follow the steps above. ‘Off?’
will be displayed. Press the ‘OK’
key. You will hear a confi rmation
‘beep’ and ‘Saved’ will be briefl y
displayed.
Changing from Centigrade to
Fahrenheit
Your monitor is pre-set to display
the temperature in Centigrade
but you can change this to
Fahrenheit.
At the parent unit:
1. Press the ‘Menu’ key and then
use the ‘Up/Down’ keys to scroll
to ‘Temperature’. Press the
‘OK’ key.
2. Use the ‘Up/Down’ keys to
scroll to ‘Degree F?’. Press the
‘OK’ key to select Fahrenheit or
the ‘Menu’ key to exit without
changing the setting. You will hear
a confi rmation ‘beep’ and ‘Saved’
will be briefl y displayed.
To change back to Centigrade
follow the steps above. ‘Degree
C?’ will be displayed. Press
the ‘OK’ key. You will hear a
confi rmation ‘beep’ and ‘Saved’
will be briefl y displayed.
Parent to parent paging
This is a useful feature if one
parent is in the baby’s room and
needs to contact the other parent.
You can also use this feature to
‘fi nd’ a mislaid parent unit.
At the baby unit:
1. Press and hold the ‘Page’ key
for 2 seconds and then release.
The parent unit will emit a tone.
At the parent unit:
1. When the page tone sounds
you can silence it by pressing any
key on the parent unit.
2. If you wish, you can speak to
your partner in the baby’s room.
Press and hold the ‘Ta l k ’ key and
speak into the front of the parent
unit. Release the ‘Ta l k ’ key to
hear what is said in the baby’s
room again.
Talk to your baby
You can speak to your baby from
the parent unit, perhaps as assurance
that you are on your way.
At the parent unit:
1. Press and hold the ‘Ta l k ’ key
and speak into the front of the
parent unit. Release the ‘Ta l k ’ key
to hear your baby again.
Note: You will not be able to
hear your baby until you release
the ‘Ta l k ’ key.
Leapfrog Advanced BM.indd 11Leapfrog Advanced BM.indd 11 26/6/08 09:10:3226/6/08 09:10:32
12
Night-light
The baby unit has a one touch
night-light which has a soft starry
glow, providing comfort and
reassurance for your baby and
allowing you to see your baby in a
darkened room. You can also turn
the night-light on from the parent
unit.
At the baby unit:
1. Press the ‘Light’ key on the
front of the baby unit. A soft light
will gently turn on. Press the
‘Light’ key again and the light will
fade off.
At the parent unit:
1. Press the ‘Menu’ key and then
use the ‘Up/Down’ keys to scroll
to ‘Night-Light’. Press the
‘OK’ key.
2. ‘On?’ will be displayed. Press
the ‘OK’ key to turn the night
light on or the ‘Menu’ key to
exit. You will hear a confi rmation
‘beep’ and ‘Saved’ will be briefl y
displayed. A light bulb icon will
appear in the display of the parent
unit to remind you that the baby
unit night-light is on.
To turn the night light off again,
follow the steps above. ‘Off?’ will
be displayed. Press the ‘OK’ key.
You will hear a confi rmation ‘beep’
and ‘Saved’ will be briefl y displayed.
The light bulb icon will disappear.
To r c h
The parent unit has a useful torch
feature with a soft beam of light
- helpful when the house is in
darkness and you need to go and
check on your baby.
At the parent unit:
1. Press and hold the ‘To r c h ’ key
to turn the light on.
Note: The torch only works when
the parent unit is switched on.
Baby feed timer
If your baby is in a routine of
regular feeding intervals you can
set the baby monitor to alert you
when your baby’s feeds are due.
You can choose to:
Set the time of the day or
night (24 hour clock) that
your baby’s next feed is due or
Set the interval between your
baby’s feed start times, e.g.,
every 3 hours 30 minutes.
Don’t forget to include the
time it takes to feed your baby.
Note: You need to set the time
and date of your parent unit to use
the baby feed timer. See page 7.
Set the fi rst or next feed time
1. Press the ‘Menu’ key and then
use the ‘Up/Down’ keys to scroll
to ‘Feed Time’. Press the ‘OK’ key.
2. ‘Set Time’ is displayed. Press
the ‘OK’ key.
•
•
Leapfrog Advanced BM.indd 12Leapfrog Advanced BM.indd 12 26/6/08 09:10:3226/6/08 09:10:32
13
3. ‘Hour’ is displayed and a
number between 00 and 23 (for
the hours of the day in 24 hour
clock). Use the ‘Up/Down’ keys
to scroll to the hour of your
baby’s feed. Press the ‘OK’ key.
4. ‘Minute’ is displayed and a
number between 00 and 59 (for
the minutes of an hour). Use
the ‘Up/Down’ keys to scroll
to the minutes past the hour for
your baby’s feed. Press the ‘OK’
key. You will hear a confi rmation
‘beep’ and ‘Saved’ will be briefl y
displayed.
Set the interval for following
feeds
At the parent unit follow the
steps 1-4 above, then:
5. ‘Set Time’ is displayed. Use
the ‘Up/Down’ keys to scroll to
‘Interval’. Press the ‘OK’ key.
6. ‘Hour’ is displayed and a
two-digit number for the hours
between your baby’s feeds. Use
the ‘Up/Down’ keys to scroll to
the hour between your baby’s
feeds, e.g., 03. Press the ‘OK’ key.
7. ‘Minute’ is displayed. Use the
‘Up/Down’ keys to scroll to the
minutes after the hour between
your baby’s feeds, e.g., 30. Press
the ‘OK’ key. You will hear a
confi rmation ‘beep’ and ‘Saved’
will be briefl y displayed.
Note: Please remember to switch
the feed alarm on as detailed in
the next section.
Turn the feed alarm on
At the parent unit follow the
steps 1-7 beginning on the
previous page and then:
8. ‘Set Interval’ is displayed. Use
the ‘Up/Down’ keys to scroll to
‘Alarm’. Press the ‘OK’ key.
9. ‘On?’ will be displayed. Press
the ‘OK’ key to turn the feed
alarm on or the ‘Menu’ key to
exit. You will hear a confi rmation
‘beep’ and ‘Saved’ will be briefl y
displayed. An alarm bell icon will
appear in the display of the parent
unit to remind you that the baby
feed alarm is set.
To turn the feed alarm off again,
follow the steps above. ‘Off?’
will be displayed. Press the ‘
OK’
key. You will hear a confi rmation
‘beep’ and ‘Saved’ will be briefl y
displayed. The alarm bell icon will
disappear.
Leapfrog Advanced BM.indd 13Leapfrog Advanced BM.indd 13 26/6/08 09:10:3326/6/08 09:10:33
14
To change the alert tone volume:
1. At step 9 above, use the ‘Up/
Down’ keys to scroll to ‘Volu me’
and press the ‘OK’ key.
2. Use the ‘Up/Down’ keys to
change the volume level. Press
the ‘OK’ key. You will hear a
confi rmation ‘beep’ and ‘Saved’
will be briefl y displayed.
Note: 5 blocks on the display =
maximum volume.
Press any key on the parent unit
to silence the alarm.
Sound sensitivity
Some babies are louder than
others! You can customise the
sound sensitivity of your baby
monitor to suit your baby. Set
the sensitivity to ‘High’ for a quiet
sleeper with a soft cry and set to
‘Low’ if your baby tends to make a
noise whilst sleeping or can make
quite loud noises before he/she is
truly crying.
At the parent unit:
1. Press the ‘Menu’ key and then
use the ‘Up/Down’ keys to scroll
to ‘Sensitivity’. Press the ‘OK’ key.
2. ‘Level’ will be displayed. Use
the ‘Up/Down’ keys to change
the sensitivity setting and press
the ‘OK’ key. You will hear a
confi rmation ‘beep’ and ‘Saved’
will be briefl y displayed.
Note: 5 blocks on the display =
maximum sensitivity.
Leapfrog Advanced BM.indd 14Leapfrog Advanced BM.indd 14 26/6/08 09:10:3326/6/08 09:10:33
15
If you are experiencing
problems with your advanced
baby monitor, there are some
quick and easy checks you can
do to help solve the problem.
The parent and baby
units will not power on
Please check that you have
correctly installed the
batteries in the parent unit
and that the mains power for
the baby unit and parent unit
charging pod is connected and
switched on.
The ‘Link’ light on the
parent unit is fl ashing, the
noise indication LEDs are
not functioning and you
cannot hear sounds from
your baby’s room
You may have moved out of
range of the baby unit. Move
the parent unit closer and wait
5 seconds for the ‘Link’ to reestablish.
You may need to manually
re-establish the link. Turn
both units off and then press
and release the ‘On/Off’ key
on both the baby and parent
units. After a few seconds the
green ‘Link’ light will come on.
•
•
•
You can’t hear your baby
on the parent unit and
the ‘Link’ light is still
glowing steadily
Check that the volume on the
parent unit is turned up.
You may need to increase the
sensitivity of the parent unit.
See page 14.
The baby monitor is
making a high pitched
ear-piercing noise
This can happen if the baby
and parent unit are too close
to each other. Move the
parent unit further apart from
the baby unit.
Clean the charging contacts
with a soft, dry cloth.
If you are experiencing any
diffi culty after making the
above checks, please call
the helpdesk for further
assistance.
Helpdesk
The helpdesk is open from
8.30am to 5.00pm, Monday to
Friday (excluding Bank Holidays)
and can be contacted on
0845 833 1673 (local rate call
charge applies).
•
•
•
•
Simple solutions
Leapfrog Advanced BM.indd 15Leapfrog Advanced BM.indd 15 26/6/08 09:10:3326/6/08 09:10:33
16
Changing the parent unit
batteries
The parent unit is supplied with 2
x AAA 1.2V 800mAh Nickel Metal
Hydride Rechargeable Batteries.
To change the batteries please
refer to page 5 of this guide.
Only use recommended
batteries or those of an
equivalent type.
Batteries are to be inserted
with the correct polarity.
Follow the diagram in the
battery compartment.
DO NOT short circuit the
supply terminals.
Promptly remove exhausted
batteries from the parent and
baby unit and replace if the
operating times have become
reduced over time.
Remove the batteries from
the parent and baby unit if
they will not be used for an
extended period of time.
DO NOT attempt to recharge
non-rechargeable batteries.
Dispose of dead batteries
properly.
DO NOT mix old and new
batteries or batteries of
different types. (i.e., alkaline/
standard)
•
•
•
•
•
•
•
•
DO NOT incinerate used
batteries.
DO NOT dispose of batteries
in a fi re, as they may explode
or leak.
DO NOT attempt to open
the battery outer casing.
Batteries are harmful if
swallowed, so keep away from
young children.
•
•
•
•
General information
Leapfrog Advanced BM.indd 16Leapfrog Advanced BM.indd 16 26/6/08 09:10:3426/6/08 09:10:34
17
Product guarantee
This product has a warranty
of 12 months and is therefore
guaranteed to be free from
defects in materials and
workmanship during that period.
If you experience a problem
within that time, simply call the
Helpdesk on 0845 833 1673 (local
rate call charge applies).
If your problem cannot be solved
by our Helpdesk, you will
need to return your product
to the place it was purchased.
Remember to take your receipt
as proof of purchase as it must be
produced before the warranty
can be honoured. This product
must have been used only for the
intended purpose and not been
subjected to wilful or accidental
damage.
This warranty does not cover
damage caused by excessive
voltage or lightning.
If this product has been tampered
with in any way, the warranty shall
be considered null and void.
This guarantee does not affect
your statutory rights.
WEEE Directive
WEEE Directive – Directive
2002/96/EC of the European
Parliament and Council of 27th
January 2003 on waste electrical
and electronic equipment.
At the end of the product’s
lifecycle, you should not
throw this product into the
normal household waste but
take it to a collection point for
the recycling of electrical and
electronic equipment. The ‘WEEE’
symbol below, on the product,
user manual and packaging
indicate this.
Please contact your local
authority if you need more
information about the collection
points in your area.
For more information telephone
Envirowise on 0800 585794.
Leapfrog Advanced BM.indd 17Leapfrog Advanced BM.indd 17 26/6/08 09:10:3426/6/08 09:10:34
Magicbox is a trademark of Euro Suisse International Ltd.
LEAPFROG and the LeapFrog Logo are trademarks or registered trademarks of LeapFrog Enterprises, Inc.
and are used under license. © 2008 LeapFrog Enterprises, Inc. All rights reserved.
Helpline
0845 833 1673
(local call rate)
June08/Issue: 1
Leapfrog Advanced BM.indd 20Leapfrog Advanced BM.indd 20 26/6/08 09:10:3426/6/08 09:10:34
Loading...