Page 1
Installation Instructions for
980MEZZOGPCF
Mezzo Grande Pendant
Suspension
GP I :ENERAL RODUCT NFORMATION
This product is suitable for damp locations.
This instruction shows a typical installation.
CAUTION - RISK OF FIRE
This product must be installed in accordance with
the applicable installation code by a person familiar
with the construction and operation of the product
and the hazards involved.
Use minimum 90°c supply conductors.
(Compact Fluorescent)
LP773_CF
1.0
Install the Mounting Plate
1A
MOUNTING
PLATE
ALLEN
WRENCH
SCREW
CANOPY
1B
MOUNTING
PLATE
2 2
#8-32 SCREW
2
Install the mounting plate to the electrical box with the
two provided #8-32 screws.
1
Remove the mounting plate from the canopy by
removing the three screws on the canopy with the Allen
wrench provided.
1
Page 2
Assemble the Fixture
2A
CABLE CLUTCH
2B
OUTER
SHADE
NIPPLE
GLASS
SHADE
CORD
STOPPER
9
SOCKET
ASSEMBLY
AIRCRAFT CABLE
7
7
7
STOPPER
7
THREADED
CAUTION: Ensure that the aircraft cable has been
fed completely through the cable clutches for proper
grip.
7
Feed the aircraft cables through the stopper and cable
clutches.
8
Feed the cord through the glass shade, stopper, and
outer shade.
9
Screw the threaded nipple on the socket assembly to the
stopper.
2C
AIRCRAFT CABLE
CORD
OUTER
SHADE
GLASS
SHADE
10
Simultaneously pull the cables and cord upward while
carefully lowering the outer shade onto the glass shade.
2
Page 3
Install the Fixture
Install the Canopy
3A
1
Take note of the wire connections and remove the wire
nuts to disconnect the power cord wires from the
ballast wires.
NOTE: Make sure to support the fixture while
adjusting the aircraft cables. An assistant is
recommended to complete the remaining steps.
3B
4
4
SET SCREW
4A
4"
1
Leave 6" of the cord behind the canopy for power
connections. Cut the excess cord.
2
From the end of the cord, strip the insulation 4" using a
sharp knife. .Make sure not to nick the inner wires
3
Strip the end of the wires.
4B
STRAIN RELIEF
CANOPY
CABLE
CLUTCH
AIRCRAFT
CABLE
2
Feed the aircraft cables through the cable clutch in the
2
POWER CORD
canopy.
3
Evenly pull the aircraft cable up through the canopy to
raise the fixture to the desired length.
4
Cut off the excess aircraft cable leaving enough for fine
leveling later.
5
Loosen the set screw in the strain relief and feed the
power cord from the fixture into the canopy port until it
is straight, then re-tighten the set screw.
5
6
4
4
Feed the fixture wires through the mounting plate
7
7
TAB
center hole and then pull them out of the electrical box.
Note: If the cord has a cloth cover, peel back or remove
the cloth where the secondary strain relief is installed.
Note: If the fixture has a cord with a cloth cover,
taping down the frayed end of the cloth may assist
in feeding it through the strain relief.
NOTE: This product does not support the “lazy cord”
look. This product was designed for a straight cord
look.
5
Install the secondary strain relief by first feeding the
power cord through it.
6
Snap the strain relief tab into place.
7
Pull the cord to take up the slack and fit the rest of the
cord in the strain relief’s openings.
3
Page 4
Install the Lamp and Diffuser
4C
9
9
8
8
8
Reconnect the power cord wires to their original
connections (reversal of 3A).
9
Connect the mounting plate and the fixture ground
wire to a suitable ground in accordance with local
electrical codes.
11
10
BALLAST
5A
DIFFUSER
LAMP
SOCKET
ASSEMBLY
1
2
10
Connect the white ballast wire to the neutral power line
wire.
11
Connect the black ballast wire to the hot power line
wire.
4D
13
SCREW
CABLE
CLUTCH
NOTE:It is recommended that one person hold the
fixture while the electrician finishes the installation.
12
Place all wires, wire nut connections, and the secondary
strain relief properly inside the canopy.
14
ALLEN
WRENCH
CAUTION: To reduce the risk of a burn or electric
shock during relamping, disconnect the power to
the fixture.
Use GX24Q-3 BaseMAX 32 Watt
Triple Tube Compact Fluorescent Lamp.
1
Reach inside the inner shade and push the lamp base
into the socket.
2
Install the diffuser to the socket assembly by screwing it
in.
3
To re-lamp, reverse this section.
SAVE THESE INSTRUCTIONS!
Align the canopy holes with the mounting plate holes
13
and secure the canopy in place by reinstalling the three
screws on the canopy with the Allen wrench provided.
14
Adjust the aircraft cables until the fixture is level; feed
the cable into the cable clutch to raise the fixture and
push in on the cable clutch nipple to release the cable
and lower the fixture.
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2014 LBL Lighting.All rights reserved. The "LBL Lighting" graphic is a
registered trademark of LBL Lighting. LBL Lighting reserves the right to
change specifications for product improvements without notification.
4
A Generation Brands Company
Loading...