Page 1
Installation Instructions for
980MEZZOGP
Mezzo Grande Pendant
Suspension
GP I :ENERAL RODUCT NFORMATION
This product is suitable for damp locations.
This product can be dimmed with a standard incandescent dimmer.
This instruction shows a typical installation.
CAUTION - RISK OF FIRE
This product must be installed in accordance with
the applicable installation code by a person familiar
with the construction and operation of the product
and the hazards involved.
Use minimum 90°c supply conductors.
LP773_
1.0
Install the Mounting Plate
1A
MOUNTING
PLATE
ALLEN
WRENCH
SCREW
CANOPY
1B
MOUNTING
PLATE
2 2
#8-32 SCREW
2
Install the mounting plate to the electrical box with the
two provided #8-32 screws.
1
Remove the mounting plate from the canopy by
removing the three screws on the canopy with the Allen
wrench provided.
1
Page 2
Assemble the Fixture
2A
CABLE CLUTCH
2B
OUTER
SHADE
NIPPLE
GLASS
SHADE
CORD
9
AIRCRAFT CABLE
7
7
7
STOPPER
7
THREADED
AIRCRAFT CABLE
STOPPER
SOCKET
ASSEMBLY
CAUTION: Ensure that the aircraft cable has been
fed completely through the cable clutches for proper
grip.
7
Feed the aircraft cables through the stopper and cable
clutches.
8
Feed the cord through the glass shade, stopper, and
outer shade.
9
Screw the threaded nipple on the socket assembly to the
stopper.
2C
AIRCRAFT CABLE
CORD
OUTER
SHADE
GLASS
SHADE
10
Simultaneously pull the cables and cord upward while
carefully lowering the outer shade onto the glass shade.
2
Page 3
Install the Fixture
Install the Canopy
NOTE: Make sure to support the fixture while
adjusting the aircraft cables. An assistant is
recommended to complete the remaining steps.
3A
STRAIN RELIEF
CABLE
CLUTCH
AIRCRAFT
CABLE
1
Feed the aircraft cables through the cable clutch in the
3
4
1
SET SCREW
CANOPY
POWER CORD
canopy.
4A
4"
1
Leave 6" of the cord behind the canopy for power
connections. Cut the excess cord.
2
From the end of the cord, strip the insulation 4" using a
sharp knife. .Make sure not to nick the inner wires
3
Strip the end of the wires.
4B
2
Evenly pull the aircraft cable up through the canopy to
raise the fixture to the desired length.
3
Cut off the excess aircraft cable leaving enough for fine
leveling later.
4
Loosen the set screw in the strain relief and feed the
power cord from the fixture into the canopy port until it
is straight, then re-tighten the set screw.
Note: If the fixture has a cord with a cloth cover,
taping down the frayed end of the cloth may assist
in feeding it through the strain relief.
NOTE: This product does not support the “lazy cord”
look. This product was designed for a straight cord
look.
5
6
4
4
Feed the fixture wires through the mounting plate
7
7
TAB
center hole and then pull them out of the electrical box.
Note: If the cord has a cloth cover, peel back or remove
the cloth where the secondary strain relief is installed.
5
Install the secondary strain relief by first feeding the
power cord through it.
6
Snap the strain relief tab into place.
7
Pull the cord to take up the slack and fit the rest of the
cord in the strain relief’s openings.
3
Page 4
Install the Lamp and Diffuser
4C
8
10
8
Connect the mounting plate and the fixture ground wire
to a suitable ground in accordance with local electrical
codes.
9
Connect the black fixture wire to the hot power line wire
with a wire nut.
10
Connect the white fixture wire to the neutral power line
wire with a wire nut.
4D
5A
9
LAMP
DIFFUSER
SOCKET
ASSEMBLY
1
2
SCREW
NOTE:It is recommended that one person hold the
fixture while the electrician finishes the installation.
11
Place all wires, wire nut connections, and the secondary
strain relief properly inside the canopy.
Align the canopy holes with the mounting plate holes
12
and secure the canopy in place by reinstalling the three
screws on the canopy with the Allen wrench provided.
ALLEN
WRENCH
CAUTION: To reduce the risk of a burn or electric
shock during relamping, disconnect the power to
the fixture.
Use Halogen120 voltMAX 100 Watt
Type A19 Medium Base Lamp.
1
Reach inside the glass shade and screw the lamp into
the socket.
2
Install the diffuser to the socket assembly by screwing it
in.
3
To re-lamp, reverse this section.
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2014 LBL Lighting.All rights reserved. The "LBL Lighting" graphic is a
registered trademark of LBL Lighting. LBL Lighting reserves the right to
change specifications for product improvements without notification.
4
A Generation Brands Company
Loading...