LBL Lighting Mademoiselle S User Manual

Installation Instructions for
980MADEMS
Mademoiselle Suspension (LED)
Suspension
GP I :ENERAL RODUCT NFORMATION
This product is suitable for damp locations.
This product may be dimmed with a low-voltage electronic dimmer.
CAUTION - RISK OF FIRE
This product requires installation by a qualified electrician. Before installing be sure to read all instructions and TURNTHE POWER TO THE ELECTRICAL BOX OFF.
Shorten the Power Cord
1A
1C
STRAIN RELIEF
6
SU697_LED
POWER CORD
1.0
POWER CORD
1
Take note of the wire connections and remove the wire nuts to disconnect the power cord wires from the driver wires.
2B
1B
3
3
STRAIN RELIEF
STRAIN RELIEF
CANOPY
CANOPY
2
2
SET SCREW
SET SCREW
CROSSBAR
CROSSBAR
CABLE CLUTCH
AIRCRAFT CABLE
4
Feed the aircraft cable through the cable clutch in the canopy.
5
2
Pull the aircraft cable up through the canopy to determine the
4
7
fixture height.
6
2
Cut off the excess aircraft cable leaving enough for fine leveling later.
7
2
Pull the power cord through the canopy to the desired length.
CANOPY
2
2
Loosen the set screw on the strain relief.(Do Not Remove)
Remove the crossbar from the canopy by completely
3
3
unscrewing the strain relief.
1
Mount the Fixture
1D
9
CORD
NOTE: The power cord does not support the fixture.
For a casual “lazy cord” look, cut the power cord several inches longer that the drop height of the fixture.
28
Once the desired look is determined, tighten the set screw on the strain relief.
9
2
Mark the cord underneath the strain relief.
1E
2A
CROSSBAR
1 1
1
Mount the crossbar assembly to the electrical box with the two provided #8-32 screws.
2B
3
3
#8-32 SCREW
4
5
4"
710
Leave 6" of the cord behind the canopy for power connections. Cut the excess cord.
7
11
From the end of the cord, strip the insulation 4" using a sharp knife. .Make sure not to nick the inner wires
7
12
Strip the end of the wires.
2
2
22
10
Reconnect the power cord wires to their original connections (reversal of 2A).
23
Ground the fixture to a suitable ground in accordance with local electrical codes.
Connect the white ballast wire to the neutral power line
4
2
wire.
Connect the black ballast wire to the hot power line
5
2
wire.
2
2C
3B
SET SCREW
STRAIN RELIEF
CORD
6
Place all wires and wire nut connections properly inside the electrical box.
7
Loosen the set screw on the primary strain relief.
8
Align the canopy center hole with the crossbar center hole.
9
Slide the canopy up against the ceiling and secure it in place by tightening the primary strain relief into the crossbar. Do not turn the cord.
10
Push the cord into the canopy and line up the marked point on the cord with the bottom of the primary strain relief.
11
Tighten the plastic set screw to secure the cord.
Install the Cable Post
CAUTION: Make sure to support the fixture while
installing, an assistant will be needed to complete the remaining steps.
2
ANCHOR
CEILING
Tap the anchor at the marked point up to the threaded portion
72
with a hammer.
3C
3
Screw the anchor in the rest of the way with a Phillips
73
screwdriver.
3D
ANCHOR
3A
24 5/16”
STRAIN RELIEF
71
Mark the cable post location point 24 5/16” away from the
CABLE POST LOCATION
center of the strain relief on the canopy.
WASHER
#8 SCREW
74
Insert the #8 screw into the threaded nipple and washer.
4
THREADED NIPPLE
Tighten the #8 screw completely into the anchor to secure the washer and threaded nipple in place.
3
Loading...
+ 5 hidden pages