LBL Lighting Lola 2-Light User Manual

Page 1
Installation Instructions for
980LOLA2W
Lola 2-Light Bath
Wall
GP I :ENERAL RODUCT NFORMATION
This product can mount either to a 4” square electrical box with a round plaster ring or an octagon electrical box.
This product can be dimmed with a standard incandescent dimmer.
This instruction shows a typical installation.
CAUTION - RISK OF FIRE
This product requires installation by a qualified electrician. Before installing be sure to read all instructions and TURNTHE POWER TO THE ELECTRICAL BOX OFF.
B 7442_A
1.0
Install the Mounting Plate
1A
FIXTURE SCREW
1
1
MOUNTING PLATE
1B
#8-32 SCREW
3 3
MOUNTING PLATE
3
Attach the mounting plate to the electrical box using the two #8-32 screws provided.
1
Remove the fixture screws located on the top and bottom of the fixture base.
2
Remove the mounting plate from the fixture base.
1
Page 2
Install the Lamps
Install the Shades ( )Curved Glass
2A
SOCKET
LAMP
Use Volt, type T4, G9 baseMAX 40120 Watt bi-pin halogen lamp in each socket.
NOTE:Use only your fingers and a soft cloth to install
3B
GLASS SHADE
SOCKET
1
Push the lamp all the way into the socket. Repeat for remaining socket assemblies.
Install the Shades ( )Rectangular Glass
NOTE: The larger shades must be installed on the
right side of the fixture.
3A
GLASS SHADE
2
Carefully install the glass shade by aligning the opening on the glass shade to the slots on the socket and rotate downward at an angle that compliments the glass shade’s curvature until it is firmly in place.
NOTE: To replace lamp, reverse section 3 and 2.
SOCKET
1
Carefully install the glass shade by aligning the opening on the shade to the slots on the socket and push it straight down onto the socket until it is firmly in place.
2
Page 3
Install the Fixture
4A
2
1
3
1
Connect the fixture to a suitable ground in accordance with local electrical codes.
4B
FIXTURE SCREW
5
5
4
Place all the wires and wire nut connections in the electrical box.
2
Connect the white fixture wires to the neutral power line wire with a wire nut.
3
Connect the black fixture wires to the hot power line wire with a wire nut.
5
Mount the fixture by sliding it back onto the mounting plate and reinstalling the two fixture screws (reversal of figure 1A).
3
Page 4
IMPORTANT SAFETY INSTRUCTIONS
Halogen Lamp General Information
To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to person:
– Use this fixture indoors only.
– Do not look directly at the lighted lamp.
– Do not remain in light if skin feels warm.
– Risk of fire: Use only the type of lamp and maximum wattage
indicated in this instruction manual.
– Never cover the halogen lamp with anything other than a LBL
Lighting lamp shield and never place flammable material close to your fixture.
– Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.
– Do not touch the fixture shades or lamp shield while the fixture
is on.These surfaces may be HOT.
– A new halogen lamp may smoke slightly when it is used for the
first time.This is perfectly normal; the protective coating is simply being vaporized.
TwoTips For Prolonging Halogen Lamp Life
– First avoid touching the lamp with bare hands during installation.
Any contaminant, even the oil from your hands can deteriorate
the lamp. Rubbing alcohol can be used to remove any contaminant.
– Second, do not run the lamps at full power when you do not need
to. However, if dimming the fixture for an extended period of time, occasionally bring the light up to full brightness for a few minutes to complete the halogen cycle.
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2014 LBL Lighting.All rights reserved. The "LBL Lighting" graphic is a registered trademark of LBL Lighting. LBL Lighting reserves the right to change specifications for product improvements without notification.
A Generation Brands Company
4
Loading...