LBL Lighting Chicago Jazz SCF User Manual

Page 1
Installation Instructions for
980CJAZZSCF
Chicago Jazz (Compact Fluorescent)
Suspension
GENERAL PRODUCT INFORMATION:
This product is suitable for damp locations.
CAUTION - RISK OF FIRE
This product requires installation by a qualified electrician. Before installing be sure to read all instructions and TURNTHE POWER TO THE ELECTRICAL BOX OFF.
PF643_CF
1.0
Assemble the Fixture
1A
GLASS SHADE
1
Gently place the glass shade into the center of the fixture frame until it is rested in position..
Preparing the Canopy
2A
CANOPY
1
Remove the crossbar from the canopy by completely unscrewing the strain relief.
2B
CROSSBAR
2 2
STRAIN RELIEF
CROSSBAR
#8-32 SCREW
2
Mount the crossbar assembly to the electrical box with the two provided #8-32 screws.
1
Page 2
2C
SET SCREW
3
Loosen the set screw on the strain relief.(Do Not Remove)
Install the fixture
3B
5
CORD
NOTE: The power cord does not support the fixture.
For a casual “lazy cord” look, cut the power cord several inches longer that the drop height of the fixture.
NOTE: Make sure to support the fixture while
adjusting the aircraft cables. An assistant is recommended to complete the remaining steps.
3A
STRAIN RELIEF
3
CABLE CLUTCH
21
Feed the aircraft cables through the cable clutches in
1
4
POWER CORD
SET SCREW
the canopy.
2
2
Evenly pull the aircraft cables up through the canopy to raise the fixture to the desired length.
2
3
Cut off the excess aircraft cable leaving enough for fine leveling later.
CANOPY
AIRCRAFT CABLE
25
Once the desired look is determined, tighten the set screw on the strain relief.
Mark the cord underneath the strain relief.
26
4
2
If necessary loosen the set screw in the strain relief and feed the power cord from the fixture into the canopy port.
Note: Taping down the frayed end of the cloth may assist in feeding it through the strain relief.
2
Page 3
Install the Canopy
4A
4"
71
Leave 6" of the cord behind the canopy for power connections. Cut the excess cord.
72
From the end of the cord, strip the insulation 4" using a sharp knife. .
73
Strip the end of the wires.
Make sure not to nick the inner wires
4B
4C
10
10
9
8
28
10
Connect the red ballast wire to one of the insulated pendant wires.
29
Connect the yellow ballast wire to the other insulated pendant wire.
12
11
BALLAST
5
6
4
24
10
Feed the fixture wires through the crossbar center hole
7
7
TAB
and then pull them out of the electrical box.
Note:
Peel back or remove the cloth where the
secondary strain relief is installed.
10
2
Connect the fixture and the crossbar ground wire to a suitable ground in accordance with local electrical codes.
11
2
Connect the white ballast wire to the neutral power line wire.
12
2
Connect the black ballast wire to the hot power line wire.
25
Install the secondary strain relief by first feeding the power cord through it.
Snap the strain relief tab into place.
26
27
Pull the cord to take up the slack and fit the rest of the cord in the strain relief’s openings.
3
Page 4
Replacing the Lamp
4D
SET SCREW
NOTE:It is recommended that one person hold the
fixture while the electrician finishes the installation.
13
Place all wires, wire nut connections, ballast, and the secondary strain relief properly inside the canopy.
14
Loosen the set screw on the primary strain relief.
15
Align the canopy center hole with the crossbar center hole.
16
Slide the canopy up against the ceiling and secure it in place by tightening the primary strain relief into the crossbar.
17
Push the cord into the canopy and line up the marked
Do not turn the cord.
point on the cord with bottom of the primary strain relief.
Tighten the plastic set screw to secure the cord.
18
STRAIN RELIEF
CORD
Adjust the Suspension Cables
6A
SOCKET
LAMP
CAUTION: To reduce the risk of a burn or electric shock during relamping, disconnect the power to the fixture.
Use GX24Q-3 Base
MAX 32 Watt
Triple Tube Compact Fluorescent Lamp.
1
Lift the socket assembly out of the fixture.
2
Remove the old lamp.
3
Push the new lamp base into the socket.
4
Insert the socket assembly back into the fixture.
5A
1
CABLE CLUTCH
1
Adjust the aircraft cables until the fixture is level; feed the cable into the cable clutch to raise the fixture and push in on the cable clutch nipple to release the cable and lower the fixture.
CABLE CLUTCH
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2012 LBL Lighting.All rights reserved. The "LBL Lighting" graphic is a registered trademark of LBL Lighting. LBL Lighting reserves the right to change specifications for product improvements without notification.
4
A Generation Brands Company
Loading...