LAZBOY 45316A, 45316B, CHR10084A-C Assembly Instructions Manual

Model: 45316A / 45316B

ASSEMBLY

Instructions

Big & Tall Executive Chair

Should you prefer to

speak with a customer

service representative,

you may call toll free :

1-855-372-2315

0-800-051-6775

2

U.S. 6am - 5pm PST,
U.K. 2pm-1am

Guidelines

FAILURE TO FOLLOW THESE WARNINGS
WHEN IN USE COULD RESULT IN INJURY

• Do not stand on the item or use as a step ladder

• The piece has been tested and approved for users

weighing up to 350lbs (159 kg) per seat.

• Do not use this item unless all bolts and screws are

firmly secured and fastened.

• Check all bolts and screws every 90 days. As

necessary tighten if any are loose.

• Lift up then move. Pushing over or dragging this

product can result in an injury or cause damage to
the floor and piece.

3

Pre-Assembly Preparation:

Please read through this instruction booklet before
beginning assembly of this item.

Two adults are recommended for assembly.

WARNING : DO NOT LET

CHILDREN PLAY IN OR

• Clear out the space for assembly and lay out all

parts on Parts List, extra room will allow you to
easily determine if all the pieces are present.

• Save all packing materials until assembly is

complete to avoid accidentally discarding smaller
parts or hardware.

• Keep small parts and pieces away from children

and pets until fully assembled.

• Please check for any loose screws and tighten them

before you use.

4

AROUND THE UNIT DUE
TO THE POSSIBLE RISK
OF INJURY.

Parts List

D1

BA

C

D

Casters Star Base Gas Lift with Telescoping Cover Seat Plate

Quantity: 5 Quantity: 1 Quantity: 1 Quantity: 1

E2

Right Arm

Quantity: 1

J

1-3/4” Screws 1-1/4” Screws

Quantity: 2 Quantity: 4 Quantity: 4

O

F

Seat Cushion Back Cushion

Quantity:1 Quantity: 1 Quantity: 1

K

G

H

Plastic Shroud

L

1-1/4” Screws with Spring Washers

M

Arm Inserts

Quantity: 2

Allen Key M5

Quantity: 1

M2

M1

D2

E1

Left Arm

Quantity: 1

I

1” Screws

Quantity: 2

N2

N

Arm Inserts

Quantity: 2

N1

5

Step 1

Step 2

Place the Star Base (B) upside down and insert 5 Casters (A) into the holes
on the Star Base (B).

A

B

Turn the Star Base (B) over and insert the Gas Lift with Telescoping Cover
(C) through the center hole on top of Star Base (B).

C

B

6

Step 3

Step 4

Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the
front of the seat plate facing the front of seat cushion). Attach by using
1-3/4” Screws (J) for the front holes of the Seat Plate (D) and 1” Screws
(I) for the rear holes of the Seat Plate (D) and tighten screws.
*Note: Tighten the screws completely.

O

J

I

D

F

Insert Levers (D1 & D2) of Seat Plate (D) to the pre-attached cable lever
receivers on the underside of Seat Cushion (F). Push down the key on
the receivers to pull out the levers.
*Note: Fix the cable for the seat plate into the plastic clips attached to
the bottom of the seat cushion.

D1

F

D

D2

Insert

Push

As semble t he le ver

Di sass emble the lev er

7

Step 5

Step 6

Attach the Back Cushion (G) to the Seat Cushion (F) by positioning the
back support plate over the Seat Plate (D) with 1-1/4” Screws (K).
*Note: Do not tighten the screws completely.

D

G

F

O

K

Insert 1-1/4" Screws with Spring Washers (L) into arm holes attaching
Arms (E1 & E2) (with the front of arms facing the front of seat cushion)
to sides of Seat Cushion (F) and Back Cushion (G).
*Note: Tighten all the screws completely. Remember to
tighten the back support plate screws.

E2

F

E1

L

G

O

8

Step 7

Step 8

Put the Plastic Shroud (H) over the Seat Plate (D) (with the front of
plastic shroud facing the front of seat cushion). Align shroud posts to
holes on bottom of Seat Cushion (F) and press into position.

F

D

Position the assembled chair upright with the seat plate facing down.
Insert the Gas Lift with Telescoping Cover (C) into the center hole of the
Seat Plate (D).

H

D

C

F

9

Step 9

Once all screws have been tightened, place the Arm Inserts (M1 & M2
& N1 & N2) into arm grooves.

M1

N1

M2

N2

10

Operating Instructions

Function Instruction - 1

To Adjust Seat Height:

While seated, lean forward and reach under the right side of the chair to
findthe lever. Lift the lever and raise your body up slightly to allow the chair
to riseto the desired height. Once desired height is reached, release lever to
lock chairat desired height. To lower the seat, lift the lever while seated. The
chair willdescend until the lever is released or the chair reaches the bottom
position.

Function Instruction - 2

To Operate Tilt Lockout:

While seated, reach under the left side of the chair to find the lever. Push
down the lever and lean back to allow the chair to tilt backwards. To lock
the chair in the upright or vertical position, sit upright and pull the lever to
the up position.

11

Function Instruction - 3

To Adjust Tension on the Tilt:

Reach under the front center of the chair, grasp the round knob (R) and turn it
counter- clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob
(R) clockwise to loosen the tilt mechanism for a lighter user. Rotate the knob (R)
until the desired resistance is reached.

R

Function Instruction - 4

360˚ Swivel:

360˚ seat swivel.

12

Limited Warranty

The exceptions or exclusions to this warranty are:

The product you have purchased is warranted against
defects in material and workmanship while owned by
the “Original Purchaser”. The term “Original Purchaser”
is defined as that party or entity which purchases these
products from an authorized dealer or retailer as shown
by the original sales receipt. This warranty does not
apply too “as is” or previously owned products.

The manufacturer warrants its products to be free from
defects in materials and workmanship (normal wear and
tear, fading and stretching excepted), for one year from
the date of purchase, except as provided below under
the limited warranty.

This warranty gives you specific rights, and you may also
have other rights, which vary from state to state (or
country to country). All warranties are limited to the

original purchaser for normal use by a maximum of two
users. Total weight capacity per chair is 350 pounds for
a single user.

• Upholstery material and foam cushion material is
warranted against defects in material and workmanship
for a period of one year, beginning on the date of
purchase as shown on the original sales receipt.

• Any warranty claim that is submitted after the limited
warranty period, or without proper proof of purchase
will not include the cost of parts, labor, or delivery on
the warranted parts within a reasonable amount of time.
We reserve the right to require damaged parts to be
returned to us upon request. Natural markings such as
scars, brands, grain variations, wrinkles, color variations,
etc. will be considered normal characteristics and not
construed as defects.

• For claims or ques
please contact the Customer Service Department
on the web at www.truecustomersupport.com.
Be prepared to provide your name, address,
daytime phone number, the model and purchase order
number of the product, date of purchase, and the store
where it was purchased. The manufacturer requires that
the original sales receipt be submitted with all requests
to confirm that you are the original purchaser according
to our written warranty.

tions concerning this w

arranty,

13