Lawmate PV-500EVO2 User Manual

Lawmate PV-500EVO2 User Manual

Last Modified on 12/23/2015 9:03 pm EST

PV-500 EVO User's Guide

Law Enforcement Products Manufacturer

Law Mate

TABLE OF CONTENT

CHAPTER 01 OVERVIEW

02 FUNCTION MODES

03 BASIC OPERATION

04 INTRODUCTION OF ALL SETTING FUNCTIONS

05 VIDEO PLAYBACK

6 VIDEO EDITING

07 PHOTO BROWSING

08 PHOTO EDITING MODE

09 SUPPORTED IMAGE FILE FORMAT

10 RECORD

11 REMOTE CONTROLLER

12 SUPPORTED VIDEO FILE FORMAT

13 SPECIFICATIONS

14 IMPORTANT

15 NOTE

Overview

PV-500EVO Main Device

Remote

Accessories

Optional

Function Modes

Basic operation

Turn on/ off of PV-500 EVO player

To Do this

Turn On

Press the Power On/ Off button about 1 sec. on PV-1000, to
turn on the power and the greeting screen will appear.

Turn Off

Press the Power On/Off button about 1sec. button on
PV-1000 or press the Power button on the remote control to
turn off PV-1000.

Using the touch screen

Tap any application to get started or tap an item in the list to choose it.
Tap icon to return last page or return back to main menu.

Tap icon or to move next page’s menu. Tap icon for function setting.

Adjust Volume

While playing Video, Tap icon / or the one in the remote controller to adjust
volume.
Volume varies in 10 steps.
Volume status will be displayed on the left–down side of screen.

Record button

Start Recording Push the REC button on the PV-500EVO or the one on the

remote controller to start recording.

Stop Recording: Press STOP button or the one on the remote controller to stop

recording, and the screen will return to stand-by mode of Preview to prepare for
recording.

Link with other equipments

External Video Source Recording– Cam in

Plug an external camera into Cam-in , it enable recording.

External Video Source Recording – Digital Cam in

Output to TV Screen:

Plug an RCA cable in AV-out to have the image output to the TV.

Precaution: Check “Setup” Menu, the setting of “Display” must be set from “LCD”

into “TV” enable image output.

Connect to wire controller:

Connect to PC:

Connect the two ends of A/B type of USB cable to PV-1000 and PC.1.
2 An indication for “USB Mode” appears on the screen for 5 seconds after the link is2.
properly installed.

Charging:

When the power goes down, power LED indictor blinks (green) and the meter with no
bars displays on the bottom right corner of the screen, which indicates that the power
of the host exhausts; please recharge it immediately. connect the main device with the
power supply and then plug the power supply into the electrical outlet. The LED light
will be on Orange.

Precaution: The LED light will be turned off after finishing charging; to keep long life-

span of the battery, the power supply should be unplugged after finishing charging; Please

charge the battery last for 12 hours before 1st time to use

Introduction to all Setting Functions

01. Preview >

Tap SETTINGS on the screen to the page1 of setting functions then Tap Preview to start
setting each function as below.

Resolution (352*288 /640*480/720*576/1024*768/1280*720/1280*960)
Quality (Good/Normal/Low)
Frame Rate( 1 / 5/ 15 /20/25)
Audio (Enable/Disable)
Frame Counter Stamp (On/Off)
Timestamp (On/Off)
Device ID Stamp (On/Off)
Display (LCD/TV/Both)
Microphone sensitivity
Over-write

Notice: For TV output, it is needed to select Display to TV or Both.

02. Pre-event >

Tap SETTINGS on the screen to the page1 of setting functions then Tap Pre-event to start
setting each function as below.

Resolution (352*288 /640*480/720*576/1024*768/1280*720/1280*960)
Quality (Good/Normal/Low)
Frame Rate ( 1 / 5/ 15 /20/25)
Audio (Enable/ Unable)
Frame Counter Stamp (On/Off)
Timestamp (On/Off)
Device ID Stamp (ON/Off)
Display (LCD/TV/BOTH)
Pre-Record Time (30 sec，15 sec)
Microphone sensitivity
Over-write (Disable/Enable)

03. Motion detection >

Tap SETTINGS on the screen to the page1 of setting functions then Tap Motion detection to
start setting each function as below.