LawMate PI RF50 User Manual
3. LED Status Indicator
1. PI-RF50 Transmitter Names and Parts
PI-RF50
LED Indicators
Blue LED Blinks Once
Red LED Blinks Once
Solid green LED
Blinking Blue LED
# Note: The Connection between the Transmitter and Receiver can
last for 20 seconds. The connection will automatically be
terminated after 20 seconds of idle time.
Device Status
Pairing Up
Commands Received
Commands Received Feedback
Charging
1 2
RF Wireless Remote Controller
LawMate, innovation never stops
1
2
3
4
5
1. Power LED(Blue)
2. Power Key
3. Rec LED(Red)
4. Rec Key
6
2. Package Content
®
Receiver
(Connecting to DVR)
7
8
5. WiFi LED(Orange)
6. Wi-Fi Key
7.Power ON(Down) /OFF(Up) Switch
8. Vibration ON(Down) /OFF(Up) Switch
Transmitter
3
3. Connect the
1. Plug in the Receiver into the Control port . Once you
see the Blue LED blinks for once, it suggests that the
Receiver is working properly.
2. To control the DVR with the Transmitter, switch to “Power
On” on the side of the Transmitter. The Blue LED will blink
once and the Transmitter will vibrate twice.
3. Press for 3 seconds to turn on the DVR, you’ll see the monitor
being turned on. Then the Red LED and Blue LED will both
be on, the DVR will start the recording automatically.
4. If you want to stop the recording, press to trun off the recording.
The Red LED on the Rec Key will be off and the Transmitter
will vibrate twice if the Rec is stopped successfully. You can resume
the Rec by pressing again. The Red LED will be on again
and the Transmitter will also vibrate twice which indicates that the
Rec has been on again.
5. If you want to start the P2P connection, please press to turn on
the Wi-Fi. The Orange LED will be on and the Transmitter will
vibrate twice, You can turn off the connection by pressing again.
* PI-RF50 supports PV-500HDW Pro only
2
PI-RF50 Receiver
3
4
to the DVR
3
4
6
6
Warning Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
o Reorient or relocate the receiving antenna.
o Increase the separation between the equipment and receiver.
o Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
o Consult the dealer or an experienced radio/TV technician
for help.
Caution: Any changes or modi?cations to this device not
explicitly approved by manufacturer could void your authority
to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference
that may cause undesired operation.
CAUTION : RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS.
Extreme temperature: -20-45
℃
Declaration of Conformity
Hereby, LawMate International Co., Ltd. declares that this
Wireless RF Remote Control product is in compliance with
essential requirements and other relevant provisions of
Directive 1999/5/EC. A copy of the Declaration of conformity
can be found at LawMate International Co., Ltd.
4
5 6
Loading...