Launch Tech WIFIPR User Manual

WI-FI PRINTER

User’s Manual

LAUNCH TECH. CO., LTD.
Launch Industrial Park, North of Wuhe

Avenue, Banxuegang, Longgang,
Shenzhen, Guangdong,

P.R.China, 518129
Tel: [phone]
http://www.cnlaunch.com
http://www.x431.com

1. Introduction

This Wi-Fi printer is an optional accessory
of a series of LAUNCH’s diagnostic devices.
The built-in Wi-Fi module enables you to
easily print the real time test results without
connecting any USB cable.

Compared to conventional printers, it is
smaller and easier to carry. Meanwhile,
being free of paper spindle, it is also simple
and fast to load printing paper. In addition
to the included DC power adaptor, it can
be powered alternatively by the built-in
rechargeable battery, which enables you to
use it anytime and anywhere.

Furthermore, this printer has auto-hibernate
and auto power-off features. While it does
not perform printing operation, it will enter
auto sleeping mode to save power. If no
activities are made within 30 minutes, it will
power off automatically. To start printing,
users need to power it on again.

2. Accessories

a)

DC adaptor x 1

b) Rechargeable Lithium battery x 1

c) Thermal printing paper x 1

3. General Controls

test whether thermal paper is properly
installed while the MODE indicator goes
out.

6) CHARGE indicator
[Green]: Indicates the battery is fully

charged.

[Red]: Indicates it is charging.

7) DC 9V adaptor jack (Note: The USB

port next to it is disabled. Do not attempt
to insert the cable into it.)

8) Rechargeable battery

4. Thermal paper loading

This Wi-Fi printer applies thermal paper roll

with size of Φ30×57mm. Follow the steps

described as below to load it.

1. Hold the side notches on the front of the
printer and lift it up to open the cover.

2. Place the unpacked thermal paper into

1
2

3

4

5

6

7

8

1) Side lock notch

2) Paper outlet

3) POWER button: Hold and press it for 2
seconds to turn it on/off.

4) MODE (ready) button: Press it to get
the printer ready or switch it to manual
feed mode.

5) FEED (paper test) button: Press it to

the compartment with its starting end
approaching to the paper outlet (refer to
the figure shown as below). Reversing
paper direction will result in that no
results will be printed out.

3. Pull out some printing paper and
introduce it along the slot until it comes
out of the paper outlet shown as below.
Otherwise, paper can not be fed.

4. Close the paper cover and press it down
until you hear a click (see the figure
shown on the next page).

5. Using the rechargeable battery

The included rechargeable battery must be
installed to ensure that the printer can print
the test result normally. This printer utilizes
a 7.2V, 1200mAh rechargeable Lithium
battery. Do the following steps to install and
charge it:

1. Align the latches
on the bottom
of the battery
with the holes
(shown as right)
on the battery
compartment.

2. Press the battery down until it is firmly

tted.

3. Press the [POWER] button for 2 seconds
to turn it on. If the battery is low, the
[POWER] indicator blinks. Please plug
the included adaptor into an outlet
to charge the battery in time. While
charging, the charge indicator turns red.
After charging is complete, the indicator
will turn green. The normal charging time
is 2 hours.

Notes:

A. Please use the included DC adaptor and

rechargeable battery only. We assume no

responsibilities for any personal injury or
loss resulting from using other adaptors or

rechargeable batteries not specied in this

user manual.

B. If the printer keeps unattended for a long

period, please remove the rechargeable
battery.

6. Wi-Fi connections

Before p rinting , you n eed to make Wi-Fi
connection and settings.

Tap “1. Settings” on the main menu of
your diagnostic tool.

Tap “2. Wi-Fi” and slide its switch to ON.
Locate and tap the 3. X-431PRINTER-

XXX (XXX stands for 3 numbers).

Input the identity password (default 4.
factory value is 12345678) and tap
“Connect”. “Connected” will appear on

the screen once it is successful.

7. How to print test results

There are three indicators on the printer:
* [POWER]: Power indicator

[Red]: Indicates that the printer is on.

[Red and blink]: Indicates that the

rechargeable battery is low.

[Off]: Indicates the printer is off.

* [MODE]: Ready indicator

[Green]: Indicates that the printer is ready.
[Green and blink]: Indicates that no thermal

paper is loaded or the printer runs out of
paper.

[Off]: Indicates that the printer is switched

to manual feed mode.

* [FEED]: Paper test indicator

[Green]: Indicates that users can press the
[FEED] button to check whether the paper
is fed normally.

[Off]: Indicates that manual mode is off.

Press the [POWER] button for 2 seconds
to turn it on, the [MODE] indicator will blink
and then remain on. (Every time you load or
change the paper, press the [MODE] button

to turn off the indicator rst, and then press

[FEED] to test whether paper can be fed
normally.) When the [MODE] indicator is on, it

shows that the printer is ready.

If the printer icon

appears on the top of the
screen, it means that printing operation can
be done. Tap it to start printing.

Notes:

A. Never expose the apparatus to sunshine,

rain, or water.

B.

Make sure that this apparatus operates in
the following conditions:

Working temperature: -10

o

C~50oC

Working humidity: 5oC RH~90oC RH.

Statement:

LAUNCH reserves the rights

to make any change to product designs and

specications without notice. The actual object

may differ a little from the descriptions in the
manual in physical appearance, color and

conguration.

Notes:
A. After loading the paper, users need to check

whether the paper can be fed normally. For
deta ils, please refer to “How to print te st
results”.

B. If the printer keeps printing for a long time,

the thermal matrixes (shown as below) will
overheat. To avoid a risk of burning injury,
please do NOT touch the matrixes.

Notice: The printer applies the thermal paper,
which should be prevented from being heated
before printing, otherwise, the paper would be
no longer effective or printing results disappear.

- 1 - - 2 - - 3 - - 4 - - 5 - - 6 - - 7 - - 8 - - 9 - - 10 -

LAUNCH LAUNCH LAUNCH LAUNCH LAUNCH LAUNCH LAUNCHLAUNCH LAUNCH LAUNCH LAUNCH LAUNCH

FCC Warning:

This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.

NOTE: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the
equipment and receiver.

-- Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.

-- Consult the dealer or an experienced
radio/TV technician for help.

RF warning

This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be
installed and operated with minimum distance
20cm between the radiator & your body.