Launch ROXIE W User Manual

i
LAUNCH ROXIE W
User Manual
Copyright Information
Copyright © 2018 by LAUNCH TECH. CO., LTD. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying and recording or otherwise, without the prior written permission of LAUNCH. The information contained herein is designed only for the use of this unit. LAUNCH is not responsible for any use of this information as applied to other units.
Statement: LAUNCH owns the complete intellectual property rights for the software used by this product. For any reverse engineering or cracking actions against the software, LAUNCH will block the use of this product and reserve the right to pursue
their legal liabilies.
Trademark Information
LAUNCH is a registered trademark of LAUNCH TECH CO., LTD. (also called LAUNCH for short) in China and other countries. All other LAUNCH trademarks, service marks, domain names, logos, and company names referred to in this manual are either trademarks, registered trademarks, service marks, domain names, logos, company names of or are otherwise the property of LAUNCH or
its afliates. In countries where any of the LAUNCH trademarks, service marks,
domain names, logos and company names are not registered, LAUNCH claims other rights associated with unregistered trademarks, service marks, domain names, logos, and company names. Other products or company names referred to in this manual may be trademarks of their respective owners. You may not use any trademark, service mark, domain name, logo, or company name of LAUNCH or any third party without permission from the owner of the applicable trademark, service mark, domain name, logo, or company name. You may contact LAUNCH by visiting the website at www.cnlaunch.com, or writing to LAUNCH TECH. CO.,
LTD., Launch Industrial Park, North of Wuhe Avenue, Banxuegang, Bantian, Longgang, Shenzhen, Guangdong, P.R.China, to request written permission to use Materials on this manual for purposes or for all other questions relating to
this manual.
General Notice
Other product names used herein are for identification purposes only and may be trademarks of their respective owners. LAUNCH disclaims any and all rights in those marks.
There is a possibility that this unit is inapplicable to some of the vehicle models or systems listed in the diagnosis section due to different countries, areas, and/or years. Do not hesitate to contact LAUNCH if you come across
such questions. We are to help you solve the problem as soon as possible.
ii
LAUNCH ROXIE W
User Manual
Disclaimer
To take full advantage of the unit, you should be familiar with the engine.
• All information, illustrations, and specications contained in this manual are
based on the latest information available at the time of publication. The right is reserved to make change at any time without notice.
• Neither LAUNCH nor its afliates shall be liable to the purchaser of this unit or third parties for damages, losses, costs or expenses incurred by purchaser
or third parties as a result of: accident, misuse, or abuse of this unit, or unauthorized modifications, repairs, or alterations to this unit, or failure to strictly comply with LAUNCH operating and maintenance instructions.
LAUNCH shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated
as Original LAUNCH Products or LAUNCH Approved Products by LAUNCH.
Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or this tool, please read
this user’s manual rst carefully and observe the following safety precautions at
a minimum whenever working on a vehicle:
Always perform automotive testing in a safe environment.
Do not attempt to operate or observe the tool while driving a vehicle.
Operating or observing the tool will cause driver distraction and could cause a fatal accident.
• Wear safety eye protection that meets ANSI standards.
• Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or
hot engine parts.
• Operate the vehicle in a well-ventilated work area: Exhaust gases are
poisonous.
• Put blocks in front of the drive wheels and never leave the vehicle unattended
while running tests.
• Use extreme caution when working around the ignition coil, distributor cap,
ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
• Put the transmission in P (for A/T) or N (for M/T) and make sure the parking
brake is engaged.
• Keep a re extinguisher suitable for gasoline/chemical/ electrical res nearby.
• Don’t connect or disconnect any test equipment while the ignition is on or the
engine is running.
iii
LAUNCH ROXIE W
User Manual
Table of Contents
1. Introduction .....................................................................................................1
2. General Information .......................................................................................2
2.1 On-Board Diagnostics (OBD) II ......................................................................2
2.2 Diagnostic Trouble Codes (DTCs) .................................................................. 2
2.3 Data Link Connector (DLC) Location .............................................................3
2.4 OBD II Readiness Monitors ............................................................................ 4
2.5 OBD II Monitor Readiness Status...................................................................5
2.6 OBD II Denitions ........................................................................................... 5
3. Product Descriptions .....................................................................................7
3.1 Outline of ROXIE W........................................................................................7
3.2 Technical Specications .................................................................................8
3.3 Accessories Checklist ..................................................................................... 9
4. Initial Use.......................................................................................................10
4.1 Charging The Tool ........................................................................................10
4.2 Getting Started .............................................................................................10
5. Diagnose .......................................................................................................14
5.1 Connection ...................................................................................................14
5.2 Smart Diagnosis (Auto-Detect) ..................................................................... 14
5.3 View Reports ................................................................................................15
6. Settings .........................................................................................................17
6.1 Wi-Fi .............................................................................................................17
6.2 Email.............................................................................................................17
6.3 Diagnostic Mode ........................................................................................... 17
6.4 Account Information ...................................................................................... 17
Keep this tool dry, clean, free from oil/water or grease. Use a mild detergent
on a clean cloth to clean the outside of the tool, when necessary.
• Please use the DC 5V power adaptor to charge this tool. No responsibility
can be assumed for any damage or loss caused as a result of using power adaptors other than the right one.
iv
LAUNCH ROXIE W
User Manual
6.5 Diagnostic Software Upgrade ....................................................................... 17
6.6 Expiration Date ............................................................................................. 18
6.7 Time Zone.....................................................................................................18
6.8 Associate Device ..........................................................................................18
6.9 Activation Code.............................................................................................18
6.10 System Version...........................................................................................18
7. ROXIE-AIT Management Platform ............................................................... 19
7.1 Sign-up .........................................................................................................19
7.2 Reports ......................................................................................................... 21
7.3 My Devices ................................................................................................... 21
7.4 Settings.........................................................................................................23
8. FAQ ................................................................................................................25
1
LAUNCH ROXIE W
User Manual
1. Introduction
ROXIE W is an evolutionary smart plug & play solution which is specialized on automotive diagnostics. Users can achieve full vehicle system diagnosis without any operation, just simply plug the device into the vehicle’s DLC(Data Link Connector) directly and then keep the vehicle ignition key on.
After diagnosis is completed, a diagnostic report will be generated on the ROX-
IE W device and sent to the registered email address automatically (if bound). In addition, user also can view the diagnostic report and manage the ROXIE W devices by visiting the ROXIE-AIT management platform (https://usait.x431.com/ getrepair) via PC.
ROXIE W has the following functions and advantages:
Support auto sign-up
Smart(Auto-Detect) Diagnosis: Once the device and the vehicle are properly
connected, the system starts auto-detect process. Once the whole diagnostic session is successfully finished, a diagnostic report will be automatically
generated and sent to your email box (if bound)
Support intelligent audio prompt of whole diagnosis process and diagnostic
result
• Support email address conguration and report review
Associate the device to any compatible diagnostic tool of Launch family for
report sharing
Support subscription renewal for unlimited service
On the ROXIE-AIT management platform, user also can
• Manage ROXIE W devices.
Choose the audio prompt language to your preference.
• Tag the report type (including Pre-repair report, Post-repair report and
Diagnostic scan) for easier identication.
• Assign the ROXIE W device to execute the specic diagnostic operation
(such as OBD only, Data stream included/not included).
• Update via Wi-Fi: Let you update your diagnostic software and system online.
2
LAUNCH ROXIE W
User Manual
2. General Information
2.1 On-Board Diagnostics (OBD) II
The first generation of On-Board Diagnostics (OBD I) was developed by the California Air Resources Board (ARB) and implemented in 1988 to monitor some
of the emission control components on vehicles. As technology evolved and the
desire to improve the On-Board Diagnostic system increased, a new generation of On-Board Diagnostic system was developed. This second generation of On­Board Diagnostic regulations is called “OBD II”.
The OBD II system is designed to monitor emission control systems and key engine components by performing either continuous or periodic tests of specic components and vehicle conditions. When a problem is detected, the OBD II system turns on a warning lamp (MIL) on the vehicle instrument panel to alert the driver typically by the phrase of “Check Engine” or “Service Engine Soon”.
The system will also store important information about the detected malfunction
so that a technician can accurately nd and x the problem. Here below follow
three pieces of such valuable information:
1) Whether the Malfunction Indicator Light (MIL) is commanded ‘on’ or ‘off’;
2) Which, if any, Diagnostic Trouble Codes (DTCs) are stored;
3) Readiness Monitor status.
2.2 Diagnostic Trouble Codes (DTCs)
OBD II Diagnostic Trouble Codes are codes that are stored by the on-board
computer diagnostic system in response to a problem found in the vehicle. These codes identify a particular problem area and are intended to provide you with a
guide as to where a fault might be occurring within a vehicle. OBD II Diagnostic
Trouble Codes consist of a five-digit alphanumeric code. The first character, a letter, identifies which control system sets the code. The second character,
a number, 0-3; other three characters, a hex character, 0-9 or A-F provide
additional information on where the DTC originated and the operating conditions
that caused it to set. Here below is an example to illustrate the structure of the
digits:
3
LAUNCH ROXIE W
User Manual
Figure 2-1
2.3 Data Link Connector (DLC) Location
The DLC (Data Link Connector or Diagnostic Link Connector) is typically a 16­pin connector where diagnostic code readers interface with the vehicle’s on­board computer. The DLC is usually located 12 inches from the center of the
instrument panel (dash), under or around the driver’s side for most vehicles. If
Data Link Connector is not located under dashboard, a label should be there
telling location. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access the connector. If
the DLC cannot be found, refer to the vehicle’s service manual for the location.
4
LAUNCH ROXIE W
User Manual
Figure 2-2
2.4 OBD II Readiness Monitors
An important part of a vehicle’s OBD II system is the Readiness Monitors, which
are indicators used to find out if all of the emissions components have been
evaluated by the OBD II system. They are running periodic tests on specific
systems and components to ensure that they are performing within allowable limits.
Currently, there are eleven OBD II Readiness Monitors (or I/M Monitors) dened by the U.S. Environmental Protection Agency (EPA). Not all monitors are supported in every vehicles and the exact number of monitors in any vehicle
depends on the motor vehicle manufacturer’s emissions control strategy.
Continuous Monitors -- Some of the vehicle components or systems are
continuously tested by the vehicle’s OBD II system, while others are tested
only under specific vehicle operating conditions. The continuously monitored components listed below are always ready:
1. Misre
2. Fuel System
3. Comprehensive Components (CCM)
Once the vehicle is running, the OBD II system is continuously checking the above components, monitoring key engine sensors, watching for engine misre,
and monitoring fuel demands.
Non-Continuous Monitors -- Unlike the continuous monitors, many emissions
and engine system components require the vehicle to be operated under specic conditions before the monitor is ready. These monitors are termed non-
continuous monitors and are listed below:
1) EGR System
2) O2 Sensors
3) Catalyst
4) Evaporative System
5) O2 Sensor Heater
5
LAUNCH ROXIE W
User Manual
6) Secondary air Injection
7) Heated Catalyst
8) A/C system
2.5 OBD II Monitor Readiness Status
OBD II systems must indicate whether or not the vehicle’s PCM’s monitor
system has completed testing on each component. Components that have been
tested will be reported as “Ready”, or “Complete”, meaning they have been tested by the OBD II system. The purpose of recording readiness status is to allow inspectors to determine if the vehicle’s OBD II system has tested all the
components and/or systems.
The Powertrain Control Module (PCM) sets a monitor to “Ready” or “Complete”
after an appropriate drive cycle has been performed. The drive cycle that
enables a monitor and sets readiness codes to “Ready” varies for each individual monitor. Once a monitor is set as “Ready” or “Complete”, it will remain
in this state. A number of factors, including erasing of Diagnostic Trouble Codes
(DTCs) with a code reader or a disconnected battery, can result in Readiness Monitors being set to “Not Ready”. Since the three continuous monitors are constantly evaluating, they will be reported as “Ready” all of the time. If testing
of a particular supported non-continuous monitor has not been completed, the
monitor status will be reported as “Not Complete” or “Not Ready.”
In order for the OBD monitor system to become ready, the vehicle should be
driven under a variety of normal operating conditions. These operating conditions
may include a mix of highway driving and stop and go, city type driving, and at least one overnight-off period. For specic information on getting your vehicle’s OBD monitor system ready, please consult your vehicle owner’s manual.
2.6 OBD II Denitions
Powertrain Control Module (PCM) -- OBD II terminology for the on-board
computer that controls engine and drive train.
Malfunction Indicator Light (MIL) -- Malfunction Indicator Light (Service
Engine Soon, Check Engine) is a term used for the light on the instrument panel.
It is to alert the driver and/or the repair technician that there is a problem with one or more of vehicle’s systems and may cause emissions to exceed federal standards. If the MIL illuminates with a steady light, it indicates that a problem
has been detected and the vehicle should be serviced as soon as possible.
Under certain conditions, the dashboard light will blink or ash. This indicates a
severe problem and flashing is intended to discourage vehicle operation. The
vehicle onboard diagnostic system cannot turn the MIL off until the necessary repairs are completed or the condition no longer exists.
6
LAUNCH ROXIE W
User Manual
DTC -- Diagnostic Trouble Codes (DTC) that identifies which section of the emission control system has malfunctioned.
Enabling Criteria -- Also termed Enabling Conditions. They are the vehicle-
specic events or conditions that must occur within the engine before the various monitors will set, or run. Some monitors require the vehicle to follow a prescribed “drive cycle” routine as part of the enabling criteria. Drive cycles vary among vehicles and for each monitor in any particular vehicle. Please refer to the vehicle’s factory service manual for specic enabling procedures.
OBD II Drive Cycle -- A specific mode of vehicle operation that provides
conditions required to set all the readiness monitors applicable to the vehicle to the “ready” condition. The purpose of completing an OBD II drive cycle is to force
the vehicle to run its onboard diagnostics. Some form of a drive cycle needs to
be performed after DTCs have been erased from the PCM’s memory or after the battery has been disconnected. Running through a vehicle’s complete drive cycle will “set” the readiness monitors so that future faults can be detected. Drive cycles vary depending on the vehicle and the monitor that needs to be reset. For vehicle specic drive cycle, consult the service manual.
Freeze Frame Data -- When an emissions related fault occurs, the OBD II
system not only sets a code but also records a snapshot of the vehicle operating parameters to help in identifying the problem. This set of values is referred to
as Freeze Frame Data and may include important engine parameters such as engine RPM, vehicle speed, air ow, engine load, fuel pressure, fuel trim value,
engine coolant temperature, ignition timing advance, or closed loop status.
Fuel Trim (FT) - Feedback adjustments to the base fuel schedule. Short-term
fuel trim refers to dynamic or instantaneous adjustments. Long-term fuel trim refers to much more gradual adjustments to the fuel calibration schedule than short-term trim adjustments. These long-term adjustments compensate for vehicle differences and gradual changes that occur over time.
7
LAUNCH ROXIE W
User Manual
3. Product Descriptions
3.1 Outline of ROXIE W
1
2
3
4
5
Figure 3-1
No. Name Descriptions
1
DB-15 diagnostic connector
To connect to vehicle's DLC (Data Link Connector) via diagnostic cable.
8
LAUNCH ROXIE W
User Manual
2 LCD Indicates test results.
3 POWER key
• In Off mode, press it for about 5 seconds to turn
the handset on.
• In On mode:
• Press it to activate the LCD if the LCD is off.
• Press it to turn off the LCD if the LCD lights
up.
• Press it for 3 seconds to turn it off.
4 Charging LED
Red means Charging and Green means Fully
charged.
5 5V Charging port
To connect to external DC power for charging the
tool.
3.2 Technical Specications
Screen: 5” touch screen
• RAM: 1G
• ROM: 8GB
• Battery: 6000mAh rechargeable Li-battery
• OBDII input voltage range: 9~18V
Charging via:
DC 5V charging cable or
Diagnostic cable through connection to vehicle’s DLC
Dimension: 3.7” x 8.5” x 1.3” (95mm x 217mm x 33mm)
Net weight: 20oz (<560g)
• Working temperature: -10 to 50°C (14 to 122 F°)
• Storage temperature: -20 to 70°C (-4 to 158 F°)
9
LAUNCH ROXIE W
User Manual
3.3 Accessories Checklist
For detailed accessory items, please consult from the local agency.
1. ROXIE W handset
2. OBD II diagnostic cable
3. DC 5V charging cable
4. User manual
5. Power adaptor
10
LAUNCH ROXIE W
User Manual
4. Initial Use
4.1 Charging The Tool
There are two charging methods available:
Via Charging Cable: Plug one end of the included charging cable into the DC-IN
port of the tool, and the other end to the external DC power.
Via Diagnostic Cable: Insert one end of the diagnostic cable into the DB-15 connector of the tool, and the other end to the vehicle’s DLC.
Once the charging LED illuminates solid green, it indicates that the battery is fully charged.
4.2 Getting Started
If it is the rst time you have used this tool, you need to complete the following
settings.
*Note: If you skip the inial sign-up and setup, alternavely you can congure it in the “Sengs” on the Job Menu.
1. Press the [POWER] button to power it on, the screen displays as follows:
?
Next
To begin using ROXIE, complete the following
steps.
ROXIE
Welcome to use
100%
Figure 4-1
11
LAUNCH ROXIE W
User Manual
In Figure 4-1, tap “Next” to go to next step.
2.
Select time zone
: Tap to select the time zone of your current location, the
system will automatically configure the system time according to the time
zone you selected. See Figure 4-2.
America/New York
Previous
Select Time Zone
Next
Please select the time zone of your current
location, the system will automatically set the system time according to the time zone you selected.
100%
?
LAUNCH_GN
LAUNCH_HW
LAUNCH_GUEST
VCX_WIFI
TP-LINK_2AKK
TP-LINK_5F_test
Previous
Select Wi-Fi Network
Next
ROXIE MUST be connected to a Wi-Fi network for it to work. Please select an available WiFi network before moving forward. If there is no available WiFi network nearby, connect via
mobile WiFi hotspot.
100%
?
Figure 4-2 Figure 4-3
After setting, tap “Next” to go to Wi-Fi setup.
3. *
Wi-Fi setup
: The system automatically searches for all available wireless
LANs. Choose the desired WLAN access point / network,
• If the network you chose is open, you can connect directly;
• If the selected network is encrypted, you have to enter the right security key (network password). Tap “OK” until the device is properly connected to the WLAN.
• If the desired Wi-Fi network does not appear on the list, swipe the screen from the top to refresh it or tap “Add network” to manually add it.
*Note: Wi-Fi setup is mandatory. If there is no available Wi-Fi network nearby, you can enable “Portable mobile hotspot” instead of the WLAN.
4.
Configure email address
: After the network connection is done, the system
automatically enters the email address setting screen. Input the email
12
LAUNCH ROXIE W
User Manual
address, and tap “Next” to go to next step.
Please input the email address
Previous
Set-up Email
Next
After ROXIE is properly connected to the
network and inspection is completed, the reports will be sent to the following email address. Carefully enter email address below
(if you enter multiple email addresses, use “;” to split). If the email address is to be changed
in the future, you may do so in Settings.
100%
Figure 4-4
*Notes:
You are strongly recommended to fill in a valid email address. After you configured it, the system will automatically send the diagnostic report to your email box every
time a complete Auto-Detect process is successfully finished.
• The email address filled in process of sign-up is the default email for receiving all
the diagnostic reports generated by the devices which are bound to this email address.
• To assign an email address to receive reports from certain device, go to ROXIE­AIT management platform -> "Set Email". For detailed operations, please refer to
Chapter 7.4.2.
5.
Fill in workshop information
: Type in the workshop name and address, and tap
“Next” to go to the next step.
13
LAUNCH ROXIE W
User Manual
*Note: Once you saved the informaon, it will be automacally generated each me the diagnosc report is saved. The workshop informaon will be appended as a personalized “tag” on the reports. If you choose to skip this step, you may set it in “Sengs” -> “Account Informaon” later.
6.
Bind ROXIE W to a compatible diagnostic scanner
: If you had purchased a diagnostic scanner of LAUNCH family, you can associate the ROXIE W device with it so that all diagnostic reports generated by ROXIE W can be viewed on the scanner. Otherwise, just tap “Next” to skip this step.
7.
User agreement
: Carefully read all terms and conditions of the user agreement,
check the box before the “Agree to all the above terms”, and tap “Complete” nish the sign-up process and go to “Congratulation” page.
8.
Finish registration
: Tap “Begin” on the congratulation page to start checking for
updates.
9.
Check for updates
: If a newer software version is detected, the system will
automatically start downloading
(*Note: Download and installaon me depends
on the internet connecon)
. After downloading is nished, ROXIE W navigates
to the Job Menu.
*Note: Updating to the latest diagnostic software can help ROXIE W obtain more accurate test results. It is recommended to check for updates on a regular basis to
keep current with the latest available soware.
4.3 Job Menu
It mainly includes the following function modules.
Report
To view all reports generated by ROXIE W.
*Note: In general, ROXIE W only saves all diagnostic reports for one year from the date the report was created.
If the device is associated with (bound to) a diagnostic scanner
of LAUNCH family, the reports will be synchronized and
appended to the Reports list of the scanner.
Settings
To make some system settings, including Wi-Fi setup, Email address for receiving diagnostic reports, Workshop
information, Associate device, Diagnostic software update,
Expiration date and System version check etc.
14
LAUNCH ROXIE W
User Manual
5. Diagnose
5.1 Connection
1. Turn the ignition off.
2. Locate vehicle’s DLC socket: It provides standard 16 pins and is generally located on driver’s side, about 12 inches away from the center of dashboard.
See Figure 2-2. If DLC is not equipped under dashboard, a label indicating its position will be given. In case no DLC is found, please refer to Automobile Repair Manual.
3. Plug one end of the diagnostic cable into the DB-15 connector of the tool, and tighten the captive screws. Connect the other end to the vehicle’s DLC.
Diagnostic Cable
ROXIE W
Vehicle's DLC
Figure 5-1
5.2 Smart Diagnosis (Auto-Detect)
After connection, turn the ignition key on and the system enters auto-detect mode.
15
LAUNCH ROXIE W
User Manual
Stop
VIN Scan
VIN Identication function is reading the vehicle
information...
Dec 17 08:59 100%
VQBEVTRTELBANCLKJ
Figure 5-2
*Note: To detect more and accurate VINs, a stable network connecon is highly recommended for this funcon.
*CAUTION: Don’t connect or disconnect any test equipment with ignion on or engine
running.
A. Once the system successfully obtains the VIN (Vehicle Identication Number)
information of the currently identified vehicle, it will continue scanning the vehicle systems. After the scanning is complete, a diagnostic report will be
automatically generated and sent to your email box (if bound).
B. If the tool failed to access the VIN information, the system will navigate to the
Job Menu.
5.3 View Reports
Tap “Report” on the Job Menu to check all diagnostic reports.
*Note: Since all reports are automacally generated and sent to your email inbox, you can go to ROXIE-AIT management plaorm to mark the report type (Pre-repair report, post-repair report and diagnosc session) to beer idenfy it.
16
LAUNCH ROXIE W
User Manual
Back
Report
Dec 17 08:59 100%
ROXIE will save all inspection reports from within one-year. For earlier reports, check your
email for reference. LAUNCH cares about your data, however, LAUNCH will not be held liable for any data loss within your email as LAUNCH will only save reports for one year from the date the report was created.
12-18-2018
12-06-2018
12-03-2018
GM
LSBXE83L8JD054794
Toyota
LFMAU92A9D0048411
Porsche
WP0AA297XCL019851
Figure 5-3
All reports are listed in date sequence. Tap certain report to view its details.
17
LAUNCH ROXIE W
User Manual
6. Settings
If you ignored some steps during sign-up, you also can use this option to set it.
6.1 Wi-Fi
This item allows you to change the Wi-Fi network.
*Note: Once WLAN is set as ON, the tool will consume more power. While it keeps
unused, please set it o to save power. While WLAN keeps unused, please turn it o to conserve baery power.
6.2 Email
This option lets you manage the email address for receiving diagnostic reports.
Add, Revise and Delete operations are available.
6.3 Diagnostic Mode
Use this item to assign the ROXIE W to execute the specic diagnostic operation
to your preference.
*Note: Alternavely, you can also set it as desired in “Sengs” on the ROXIE-AIT management plaorm.
6.4 Account Information
Once you saved the information, it will be automatically generated each time the diagnostic report is saved. The workshop information will be appended as a
personalized “tag” on the reports.
Type in the workshop name and address, tap “Save”.
6.5 Diagnostic Software Upgrade
If some new software or APK can be updated, a numeric indicator will display on the “Upgrade” module on the Job menu. In this case, you may use this option to
keep it synchronized with the latest version.
*Notes:
• To enjoy more funcons and beer service, you are strongly suggested to update it
on regular basis.
• This funcon requires a stable network connecon.
18
LAUNCH ROXIE W
User Manual
Once download is nished, the software packages will be installed automatically.
6.6 Expiration Date
This item enables you to check the expiration date and renew your subscription.
If the service period expires, tap "Next" to go to the renewal page. Fill in the 24 digits of the Subscription Renewal Card, tap "Submit".
*Notes:
To avoid purchasing a forfeit Subscription Renewal Card, please purchase it from authorized LAUNCH dealers.
• All renewal history can be accessed and checked in "Renewal record" on the ROXIE­AIT management plaorm.
6.7 Time Zone
This item enables ROXIE W to automatically configure the system time
according to the selected time zone.
6.8 Associate Device
If you had purchased a diagnostic scanner of LAUNCH family, you can associate the ROXIE W device with it so that all diagnostic reports generated by ROXIE W
can be viewed on the scanner.
Enter the product S/N of the diagnostic scanner and tap “Save” to bind it.
6.9 Activation Code
The activation code is automatically generated by the system (differ from device
to device). It shall apply when user binds a ROXIE W device on the diagnostic
scanner.
6.10 System Version
This option allows you to make OTA update of ROXIE W system.
Tap “Check version” to detect whether there is a newer version available on the
server.
19
LAUNCH ROXIE W
User Manual
7. ROXIE-AIT Management Platform
This platform is specially designed for workshops to better manage ROXIE / AIT
series devices and view reports.
7.1 Sign-up
1. Open the browser, input https://usait.x431.com/getrepair to open the login page.
Login
*Account Please Enter Email
*Password Please Enter Password
Login
Forgot Password New Registration
Fig. 7-1
A. For new users, click "New Registration" to go to Step 2.
B. For existing users, input your Email and password, then click "Login" to navigate to
the Job Menu screen.
C. If you forgot the password, click "Forgot Password" to reset a new password.
2. Click "New Registration" to open the sign-up page. See Fig. 7-2.
3. Input the information:
• In Account Info box, input the Email address, password and select the time
zone
(*Note: Since the diagnostic report is time stamped, please set the accurate
time zone
).
• In Device Info box, select the device language (
the audio prompt language
),
input the S/N and Verication code.
20
LAUNCH ROXIE W
User Manual
*Note: Serial number is a 12-digit number starting with 98 – you can find it on the back of your tool. Verification code is a 8-digit number stored in the Private & Condenal sheet.
After inputting all the info, click "Register" to bind the device to the current
account, the Job Menu screen will be open automatically.
Register
Account Info
*Account Please Enter Email
*Password Please Enter Password
*Confirm Password Enter The Password Again
*Time Zone Please Select
Device Info
*Language Please Select
*Device SN Please Enter Device SN
*Verification Code Please Enter Verification Code
Register
Return Login
Fig. 7-2
21
LAUNCH ROXIE W
User Manual
LAUNCH
Reports
My Devices
Settings
Change Password
Set Email
Business Info
Time Zone
Change Language
Renewal Record
Diagnostic Mode
yihui.qiu@cnlaunch.com
Device S/N Please Select VIN Please Enter VIN Please Enter Start Time - Please Enter End Time
Search
S/N: 989760001031 VIN : WBAFG2102BL507724
DTC: 2 Inspection Date: 09/26/2018 06:09:00
S/N: 989760001031 VIN : WBAFG2102BL507724
DTC: 2 Inspection Date: 09/26/2018 06:00:59
S/N: 989760001031 VIN : WBAFG2102BL507724
DTC: 2 Inspection Date: 09/26/2018 03:48:25
S/N: 989760001031 VIN : WBAFG2102BL507724
DTC: 2 Inspection Date: 09/26/2018 02:28:41
View Report
View Report
View Report
View Report
Fig. 7-3
7.2 Reports
Once the device successfully generates a diagnostic report, the report will stick
on top of the report list. All reports are listed in date sequence and the default
report list is blank.
*Note: To easily compare the pre-repair and post-repair reports, you are strongly
recommended to mark each report with a tag immediately after it is created.
Search: If there are too many diagnostic reports available, user can do quick lter by S/N (
*if several devices are bound to the current account
), VIN or date.
View report: Click it to view the current report.
7.3 My Devices
The option allows you to manage your devices and renew your subscription.
Click "My Devices", a screen similar to the following appears.
22
LAUNCH ROXIE W
User Manual
LAUNCH
Reports
My Devices
Settings
Change Password
Set Email
Business Info
Time Zone
Change Language
Renewal Record
Diagnostic Mode
yihui.qiu@cnlaunch.com
S/N: 986990000223 Language : English
Register Date: 12/12/2018 12:32:23 Service Valid Date: 06/20/2018 01:01:18
S/N: 989760001031 Language : English
Register Date: 12/12/2018 12:32:23 Service Valid Date: 09/20/2019 12:12:06
S/N: 979690000012 Language : English
Register Date: 12/12/2018 12:32:23 Service Valid Date: 12/03/2019 02:02:21
Renew
Renew
Renew
Unbind
Already Expired
Add New Device
Unbind
Unbind
Fig. 7-4
Add New Device: Click it to bind a new device to the current account.
Add New Device
*Language Please Select
*Device SN Please Enter Device SN
*Verification Code Please Enter Verification Code
Cancel Confirm
Fig. 7-5
Unbind: Click it to unbind the device from the current account. After unbinding, all reports generated by this device will no longer be sent to the current E-mail address.
23
LAUNCH ROXIE W
User Manual
Renew: If the service period expires, the device will be labelled as "Already Expired". Tap "Renew" to renew your subscription.
LAUNCH
Reports
My Devices
Settings
Change Password
Set Email
Business Info
Time Zone
Change Language
Renewal Record
Diagnostic Mode
yihui.qiu@cnlaunch.com
Please confirm the information
S/N: 979690000012 Service Date: 12/03/2019 02:02:21 Annual Service Fee: XXX
My Devices / Renew
Choose payment type
1. PayPal
2. Prepaid Pin Card Activate the Card
Fig. 7-6
There are two renewal options available: Paypal and Subscription Renewal Card.
If you choose PayPal to make payment, click "PayPal" and follow the on-screen instructions to proceed until the transaction is successfully nished.
If you prefer to use the Subscription Renewal Card
(*available for purchase from
local dealers)
, click "Activate the Card", and input the password of Subscription
Renewal Card, and then click "Conrm".
All renewal records can be accessed and checked from "Settings" -> "Renewal Record".
*Note: To avoid purchasing a forfeit Subscription Renewal Card, please purchase it from authorized LAUNCH dealers.
7.4 Settings
Change Password: To modify the login password.
24
LAUNCH ROXIE W
User Manual
Set Email: To set the Email address for receiving the diagnostic reports.
Business Info: To add or revise the company information.
Time Zone: To congure the time zone.
Change Language: To change the audio prompt language of the ROXIE device during the diagnostic session.
Renewal Record: To check the renewal history, binding bank card or revoke.
Diagnostic Mode: Assigns the device to execute the specic diagnostic operation for saving time.
(Log out): Tap to exit from current account.
25
LAUNCH ROXIE W
User Manual
8. FAQ
Here we list some frequently asked questions and answers related to this tool.
1
System halts when reading data stream. What is the reason?
It may be caused by a slackened connector. Please turn this tool off, firmly
connect the connector, and switch it on again.
2
Screen of main unit ashes at engine ignition start.
Caused by electromagnetic disturbing, and this is normal phenomenon.
3
There is no response when communicating with on-board computer.
Please confirm the proper voltage of power supply and check if the throttle
has been closed, the transmission is in the neutral position, and the water is in proper temperature.
4
What to do if the system fails to start auto VIN detection?
Please check the tool is properly connected to the vehicle’s DLC.
5
How to upgrade the system software?
1. Switch the tool on and ensure a stable internet connection.
2. Tap “Settings” on the Job Menu, select “System Version”, and tap “Check version” to enter the system upgrading page.
3. Follow the on-screen instructions step by step to finish the process. It may
take several minutes depending on the internet speed, please be patient. After
upgrade is successfully nished, the tool will automatically restart and enters
the Job menu.
26
LAUNCH ROXIE W
User Manual
Warranty
THIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE LAUNCH PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYER’S BUSINESS.
LAUNCH electronic product is warranted against defects in materials and workmanship for one year (12 months) from date of delivery to the user.
This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent
with instructions regarding use. The exclusive remedy for any automotive meter
found to be defective is repair or replacement, and LAUNCH shall not be liable
for any consequential or incidental damages.
Final determination of defects shall be made by LAUNCH in accordance with
procedures established by LAUNCH. No agent, employee, or representative of
LAUNCH has any authority to bind LAUNCH to any afrmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein.
Order Information
Replaceable and optional parts can be ordered directly from your LAUNCH
authorized tool supplier. Your order should include the following information:
1. Quantity
2. Part number
3. Item description
Customer Service
If you have any questions on the operation of the unit, please contact local
dealer, or contact LAUNCH TECH. CO., LTD.:
Website: www.x431.com
www.cnlaunch.com
Phone: +86 755 8455 7891
Email: overseas.service@cnlaunch.com
Statement: LAUNCH reserves the rights to make any change to this manual without notice. We have tried our best to make the descriptions and illustrations in the
manual as accurate as possible, and defects are inevitable, if you have any queson,
please contact local dealer or LAUNCH TECH. CO., LTD., LAUNCH does not bear any responsibility arising from misunderstandings.
FCC Warning:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types Automotive AI Inspection Terminal with model ROXIE W (FCC ID: XUJROXIE) has also been tested against this SAR limit. The highest reported SAR values for body-worn is 1.19 W/kg. This device was tested for typical body-worn operations with the back of the handset kept 0mm from the body. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.
Loading...