Lanpro LP-SGW2404FP Installation Manual

REV1.0.0

LPSGW2404FP_IG_ENB01W

LP-SGW2404FP
24 Copper PoE + 4 Fiber Gigabit Ma nage d Switc h

FCC Statement

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including
interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.

CE Mark Warning

This is a Class A product. In a dom estic environment, this product m ay cause
radio interference, in which case the user may be required to take adequate
measures.

SAFETY NOTICES

Caution:

Do not use this p roduct near water, for e xample, in a wet basem ent or near a
swimming pool.

Avoid using this product during an electrical storm. There may be a remote risk of
electric shock from lightning.

CONTENTS

Package Contents ..........................................................................1

Chapter 1

1.1

1.2 Guide Overv iew

Chapter 2 Devi ce D es cri pt i on

2.1 Intro duc ti o n to t he D evi c e

2.2 Features

2.3 Technical Specifications

Chapter 3 Mounting Device

3.1

3.2 Installation

3.3 Connect to Ground

Chapter 4 Switch

4.1 Front Panel

4.2

4.3 Note

Chapter 5 Configuration

5.1 Configure the Switch via GUI

5.2 Conf igur e the Sw i tch v i a CLI

Introduction

Intended Audience

................................................................................3

Precautions

Back Panel

....................................................................................11

.....................................................................2

..................................................................2

......................................................................2

.............................................................6

............................................................................6

.............................................................................6

.................................................................8

Appearance

............................................................................9

..........................................................................11

................................................................12

..........................................................3

........................................................3

..........................................................4

Description ....................................9

.................................................12

..................................................13

Appendix A: Troubleshooting .....................................................15

Package Contents

The following contents should be found in your package:

 One LP-SGW2404FP switch
 One power cord
 One console cable
 One ground cable
 Two mounting brackets and other fittings
 Installation Guide
 Resource CD for LP-SGW2404FP switch, including:

• User Guide

• CLI Reference Guide

• Other Helpful Information

 Note:

Make sure that the package contains the above items. If any of the listed
items are damaged or missing, please contact your distributor.

1

Chapt er 1

Thank you for choosing the LP-SGW2404FP. The switch provides a friendly
management interface and excellent performance.

1.1

This guide is intended for network administrators familiar with IT concepts and
network terminology.

Intended Audience

Introduction

1.2 Guide Ov erv iew

This Installation Guide is divided into the following sections to provide
concise information for configuring, and managing the device.

Chapter 1: Introduction.
Chapter 2: Device Description -- Provides an overview about the switch.
Chapter 3: Mounting Device -- Describes the mounting procedure of the switch.
Chapter 4: Switch Appearance Description -- Describes external components of

the switch.
Chapter 5: Configuration -- Instructs you to configure the switch via Web Interface

and CLI commands.
Appendix A: Troubleshooting.

2

Thi s t ec hno logy de s c r ibe s a sy s tem to t r a ns m it ele c tri c al power, alo ng wit h

device po wered by a P S E and t hus c o nsumes e ne r gy . E xamples i nc lude

Chapter 2 Device Description

2.1 Introduction to the Device

The LP-SGW2404FP switch, designed for workgroups and departments,
provides wire-speed performance and abundant layer 2 management features. It
provides a va riety of ser vice feat ures and multipl e powerful func tions with high
security.

The E IA-standa rdized fram ework and sm art configuration capacity can provide
flexible solutions for a variable scale of networks. ACL, 802.1x and Dynamic ARP
Inspection provide robust secu rity strategies. QoS and IGMP snooping/filtering
optimize voice and video application. Link aggregation (LACP) increases
aggregated bandw idth, opti mizing th e transport of business c ritical dat a. SNMP,
RMON, WEB/CLI/Telnet Log-in bring abundant management policies. The
LP-SGW2404FP switch integrates multiple functions with excellent performance,
and is friendly to manage, which can fully meet the need of the users demanding
higher networking performance.

LP-SGW2404FP Managed PoE Sw itch is also a Power Sourcing Equipment
(PSE*). All the Auto-Nego tiation RJ45 po rts on the s witch support Power o ver
Ethernet (PoE*) function, w hich can autom atically detect and suppl y pow er with
those powered devices (PDs*) complying with IEEE 802.3af and IEEE 802.3at.

PSE: A dev ice ( s witch or hub f o r instance) tha t will pr ov ide po wer i n a Po E s etup.
PoE:

data, to remote devices over standard twisted-pai r c able i n an Etherne t .

PDs: A

powerin g IP tel ephon es, wireles s LAN acce ss poin ts, net work came ras,
network hubs, embedded computers etc.

2.2 Features

 Resiliency and Availability

+ Link aggregati on (LACP) increas es aggregated ba ndwidth, optimizing the
transport of business critical data.

+ IEEE 802.1s Multiple Spanning Tree provides high link availability in multiple
VLAN environments.

+ Multicast snooping automatically prevents flooding of IP multicast traffic.
+ Root Guard protects root bridge from malicious attack or configuration

mistakes

 Layer 2 Switching

+ Supports up to 4K VLANs simultaneously (out of 4K VLAN IDs).

3