Lanpro LP-1540ai User Manual

LP1540ai_UG_ENB01W

LP-1540ai

User Guide.

Initial conguration

www.lanpro.com

www.lanpro.com

LP-1540ai ● Fast Installation Guide

Table of Contents

LP-1540ai.

Main Features...........................................................................

05

1.- LP-1540ai installation .......................................................... 07

2.- Access to the equipment ...................................................... 10

3.- Router Mode pre-loaded template values modication .............. 12

4.- How to add additional pre-conguration templates ................... 22

www.lanpro.com

www.lanpro.com

LP-1540ai ● User Guide ● ● 05

LP-1540ai

The LP-1540ai is a powerful Access Point with a 27dBi EIRP and 300Mbps
of data air rate on the 2.4 GHz band, it is PoE powered and boasts multiple
physical and virtual interfaces and VLAN support. The LP-1540ai is designed
for outdoor service.

Main Features

EIRP power of
27dBm±1.5dBm

Complies with

IEEE802.11 b, g and n

standards.

Supports high data

transfer rates on the air
of up to 300 Mbps,

When in IEEE802.11n

mode with two air
streams.

Good reception

sensitivity with a peak of

67dBm±1.5dBm at 300
Mbps and a EIRP power

of (500mW) for ample
WiFi coverage.

Supports creation

of multiple logical

interfaces.

Provides MAC Access
Control.

Provides multiple SSIDs.

Web based conguration

and Support.

Supports advanced
Firewall for physical and

logical interfaces (Global

and Individual).

Firmware update via web
browser.

Basic diagnostics

support embedded in the

rmware.

Provides 10/100 Mbps
Ethernet support and
automatic MDI/MDIX.

The rmware includes
(Load, Trafc, Wireless

and physical Connections),

with monitoring panel.

Performs Execution of

Programmed tasks.

Supports automatic
adjustment of air data
transfer rate.

Loader of Updates is
Supported.

Supports automatic air
rate speed.

Supports MAC address

ltering; wireless security
on-off; 64/128/152bit WEP

encryption and PA-PSK/

WPA2- PSK WPA/WPA2,

with of reinforcement of
security mechanisms for
Data Transmission.

Advanced Routing

adjustment support.

Advanced DHCP, DNS
characteristics, Firewalls
and NAT.

A DHCP Server has been
included.

www.lanpro.com

06 ● ● LP-1540ai ● User Guide

WMM Support, better
voice ow in videos.

Support of VLAN for
some interfaces.

Supports Span-Tree
Protocol 802.3d

Support of LAN Host
names table.

Supports QoS, used for
better quality of service
delivery.

----

The LP-1540ai, is a product that has features not found in similar equipment

in the same category. The LP-1540ai permits a granular conguration of

functionalities based on your needs.

In this fast installation guide you will nd how to modify the base conguration

loaded in the equipment (Router Mode) in which with few adjustments will
convert in your Internet Access Router.

Additionally, a description of how to load the different pre-congured

templates. For details on the templates, you must refer to each independently
made document.

If you require advanced functions, please review the User Manual
(LP1540ai_UM_ENB01W) in which a detailed description of all the

congurations is explained; please take in mind that this document purpose

is that you can set-the equipment up rapidly.

This process has been divided into four sections as follows:

1. How to install the LP-1540ai.

2. Accesing the LP-1540ai.

3. Modifying the Router Mode Template values.

4. How to add additional templates for pre-conguration.

Then each of the sections is as follows:

LP-1540ai ● User Guide ● ● 07

1. LP-1540ai installation

Proceed to check that the package contains the following components:

►

1 LP-1540ai radio.

►

1 Ethernet CAT 5e PatchCord

►

1 PoE injector.

►

1 Power cable for the PoE injector.

►

1 Documentation CD.

►

1 AC/DC Power Converter.

Figure 1.

Please proceed to make a layout plan for the equipment installation.

1.1 Please dene the equipment application (AP, Router, PtP, Etc.)

● The WAN port won’t be used in the AP or PtP congurations, only
as an auxiliary port in this conguration (Please refer to the user
manual LP1540ai_UM_ENB01W). Please note that in this manual,

the Router mode will be used as a reference.

1.2 Please dene if the equipment’s power will be through the PoE input

or through the DC Input connector.

● An AC power outlet will be needed if you plan to power up the

LP-1540ai through the DC Power input connector, please take
precautions for protecting this connection from weather if it is going

to be outdoors.

www.lanpro.com

08 ● ● LP-1540ai ● User Guide

▪ In regard with data wiring, in this type of powering connection,

a data cable must be installed between the LP-1540ai and the

corresponding data outlets. In this document in Router mode, both
(LAN y WAN) ports must be connected to the corresponding points:

▫ From the LP-1540ai LAN port to the internal LAN Switch or the

PC’s Ethernet port, or to the serviced equipment.

▫ From the WAN port of thel LP-1540ai to the Switch or ADSL

providing the internet connection.

Figure 2.

Figure 3.

● If you plan to power your LP-1540ai up with the non-standard PoE

injector, please take in mind any distance limitation imposed by
losses in the cabling used. A rule of thumb when not sure enough
is to limit the distance to 80m, this supposes the use of good wiring
standards of workmanship and the following of the local standards.

▪ In regard with data wiring, in this type of powering connection,

a data cable must be installed between the LP-1540ai and the

corresponding data outlets. In this document in Router mode, both
(LAN y WAN) ports must be connected to the corresponding points.