Lang Manufacturing LG24SM Service Manual

Installation, Operation, Maintenance, & Troubleshooting

Model: LG24SM, LG36SM, LG48SM, LG60SM, & LG72SM

Electric, Selectronic Marine Griddle

Serial:

Lang Manufacturing Company 6500 Merrill Creek Parkway Everett, WA 98203

Rev. B WWW.LANGWORLD.COM © Copyright 2001

Phone: [phone] Fax: [phone]

THE INFORMATION IN THIS MANUAL IS CRUCIAL AND MUST BE
RETAINED FOR FUTURE REFERENCE. READ, UNDERSTAND AND
FOLLOW THE INSTRUCTIONS AND WARNINGS CONTAINED IN THIS
MANUAL.

DANGER

WARNING

CAUTION

NOTICE

POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT
AVOIDED, COULD RESULT IN DEATH.

POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT
AVOIDED, COULD RESULT IN DEATH OR SERIOUS INJURY.

POTENTIALLY HAZARDOUS SITUATION WHICH, IF NOT
AVOIDED, MAY RESULT IN MINOR OR MODERATE INJURY.

Helpful operation and installation instructions and tips are
present.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS
AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION,
SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY
OR DEATH. READ THE INSTALLATION, OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS
EQUIPMENT.

Model #: Purchased From:

Serial #: Location:

Date Purchased: Date Installed:

Purchase Order #: For Service, Call:

NOTICE:

UL# E8138 2 REV B.

THIS EQUIPMENT IS APPROVED FOR INSTALLATION ONLY ON VESSELS

GREATER THAN 65 FEET IN LENGTH, IN ACCORDANCE WITH USCG
REGULATIONS IN TITLE 46 CFR 110-113. ANY WIRING USED IN THE
INSTALLATION OF THIS APPLAINCE MUST BE STRANDED COPPER.

TABLE OF CONTENTS

CHAPTER PAGE

1. TABLE OF CONTENTS ............................................................................... 3

2. READ FIRST ................................................................................................. 4

3. EQUIPMENT DESCRIPTION...................................................................... 6

4. UNPACKING ................................................................................................ 7

5. INSTALLATION........................................................................................... 8

6. INITIAL START-UP ..................................................................................... 10

7. OPERATION ................................................................................................. 11

8. CLEANING ................................................................................................... 12

9. TROUBLESHOOTING ................................................................................. 13

10. PARTS LIST.................................................................................................. 15

11. WIRING DIAGRAM..................................................................................... 16

12. WARRANTY................................................................................................. 18

UL# E8138 3 REV B.

IMPORTANT READ FIST IMPORTANT

CAUTION

CAUTION

CAUTION

DANGER

WARNING

NOTICE

NOTICE

THE UNIT IS EXTREMELY HEAVY. FOR SAFE HANDLING, INSTALLER
SHOULD OBTAIN HELP AS NEEDED, OR EMPLOY APPROPRIATE
MATERIALS HANDLING EQUIPMENT (SUCH AS A FORKLIFT, DOLLY, OR
PALLET JACK) TO REMOVE THE UNIT FROM THE SKID AND MOVE IT TO
THE PLACE OF INSTALLATION.

ANY STAND, COUNTER OR OTHER DEVICE ON WHICH UNIT WILL BE
LOCATED MUST BE DESIGNED TO SUPPORT THE WEIGHT OF THE UNIT.

SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK WHEN
CUT.

THIS APPLIANCE MUST BE GROUNDED AT THE TERMINAL PROVIDED.
FAILURE TO GROUND THE APPLIANCE COULD RESULT IN
ELECTROCUTION AND DEATH.

INSTALLATION OF THE UNIT MUST BE DONE BY PERSONNEL
QUALIFIED TO WORK WITH ELECTRICITY AND PLUMBING. IMPROPER
INSTALLATION CAN CAUSE INJURY TO PERSONNEL AND/OR DAMAGE
TO EQUIPMENT. UNIT MUST BE INSTALLED IN ACCORDANCE WITH ALL
APPLICABLE CODES.

The data plate is located behind the access panel located between the
grease drawer and the control box. The unit voltage, wattage, serial
number, wire size, and clearance specifications are on the data plate.
This information should be carefully read and understood before
proceeding with the installation.

The installation of any components such as a vent hood, grease
extractors, fire extinguisher systems, must conform to their applicable
National, State and locally recognized installation standards.

NOTICE

CAUTION

CAUTION

WARNING

CAUTION

UL# E8138 4 REV B.

During the first few hours of operation you may notice a small amount of
smoke coming from the griddle surface, and a faint odor from the smoke.
This is normal for a new unit and will disappear after the first few hours of
use.

ALWAYS KEEP THE AREA NEAR THE APPLIANCE FREE FROM
COMBUSTIBLE MATERIALS.

KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN AND DRY. IF SPILLS
OCCUR, CLEAN IMMEDIATELY, TO AVOID THE DANGER OF SLIPS OR
FALLS.

KEEP WATER AND SOLUTIONS OUT OF CONTROLS. NEVER SPRAY OR
HOSE CONTROL CONSOLE, ELECTRICAL CONNECTIONS, ETC.

MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES, MUCOUS
MEMBRANES AND CLOTHING. PRECAUTIONS SHOULD BE TAKEN TO
WEAR RUBBER GLOVES, GOGGLES OR FACE SHIELD AND
PROTECTIVE CLOTHING. CAREFULLY READ THE WARNING AND
FOLLOW THE DIRECTIONS ON THE LABEL OF THE CLEANER TO BE
USED.

IMPORTANT READ FIST IMPORTANT

NOTICE

WARNING

CAUTION

Service on this, or any other, LANG appliance must be performed by
qualified personnel only. Consult your authorized service station
directory or call the factory at 1-800-224-LANG (5264), or
WWW.LANGWORLD.COM For the service station nearest you.

BOTH HIGH AND LOW VOLTAGES ARE PRESENT INSIDE THIS
APPLIANCE WHEN THE UNIT IS PLUGGED/WIRED INTO A LIVE
RECEPTACLE. BEFORE REPLACING ANY PARTS, DISCONNECT THE
UNIT FROM THE ELECTRIC POWER SUPPLY.

USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY
LANG OR THEIR AUTHORIZED DISTRIBUTORS CAN CAUSE BODILY
INJURY TO THE OPERATOR AND DAMAGE TO THE EQUIPMENT AND
WILL VOID ALL WARRANTIES.

UL# E8138 5 REV B.

EQUIPMENT DESCRIPTION

Lang Model: Lang Model: LG-SM

Exterior Construction

The griddle dimensions are 17” (43.18cm) High, 30” (76.20cm) Deep, and width is
dependent on the actual model number.

The Sides, Bottom, and Rear wall are constructed of double wall stainless steel,
which allows closer installation to combustible surfaces.

The griddle surface is made of 1” thick, highly polished steel to reduce hot and cold
spots, recovery problems, warping, and ensure even heat to the edges of the griddle.

Controls

Each twelve-inch section has its own temperature selector switch that snaps into
place to lock in any temperature from 175°F to 450°F in 25° increments.

Each twelve-inch section of the griddle is controlled by an area sensitive RTD probe,
which can sense and react to a temperature change of +/- 4°F.

Each twelve-inch section has a set of 6 K.W. elements for high efficiency, quick
recovery and outstanding performance

Technical

The LG-S griddle operates on either 208/240V or 480V. This must be specified
when ordering.

Minimum clearances: 2” from side and back

UL# E8138 6 REV B.