Lang 224ZS, 236ZS, 260ZS, 272ZS, 224ZSD Installation And Operation Instructions Manual

...

Download

Page 1

ENVIROZONE SELECTRONIC

GAS GRIDDLE

Commercial

224ZS, 236ZS, 248ZS, 260ZS, 272ZS

224ZSD, 236ZSD, 248ZSD, 260ZSD, 272ZSD

Installation and

Operation

Instructions

2M-W2014 Rev. A 5/20/14

IL2810

236ZS

Page 2

SAFETY SYMBOL

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN

The installation of the Appliance must conform to the NATIONAL FUEL GAS CODE "ANSI Z223.1 - LATEST EDITION" AND ALL LOCAL GAS COMPANY RULES AND REGULATIONS.

IN CANADA INSTALLATION SHALL BE IN ACCORDANCE WITH THE CURRENT CAN/CGA-B149.1 NATURAL GAS INSTALLATION CODE OR CAN/CGA-B149.2 PROPANE INSTALLATION CODE AND LOCAL CODES WHERE

APPLICABLE.

INSTRUCTIONS TO BE FOLLOWED IN THE EVENT USER SMELLS GAS. THIS INFORMATION

SHALL BE OBTAINED BY CONSULTING YOUR LOCAL GAS SUPPLIER. AS A MINIMUM, TURN

OFF THE GAS AND CALL YOUR GAS COMPANY AND YOUR AUTHORIZED SERVICE AGENT.

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN

CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATION

& MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS

These symbols are intended to alert the user to the presence of important operating and maintenance instructions in the manual accompanying the appliance.

FOR YOUR SAFTEY

THE VICINTIY OF THIS OR ANY OTHER APPLIANCE.

POST IN PROMINENT LOCATION

EVACUATE ALL PERSONNEL FROM THE AREA.

WARNING

EQUIPMENT.

WARNING

RISK OF FIRE OR ELECTRIC SHOCK

DO NOT OPEN

WARNING, TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE

CONTROL PANEL. NO USER-SERVICABLE PARTS INSIDE. REPAIRS SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY.

NOTICE

Using any part other than genuine Lang factory supplied parts relieves the manufacturer of all liability.

Lang reserves the right to change speci cations and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.

Due to periodic changes in designs, methods, procedures, policies and regulations, the specifications contained in this sheet are subject to change without notice. While Lang Manufacturing exercises good faith efforts to provide information that is accurate, we are not responsible for errors or omissions in information provided or conclusions reached as a result of using the speci cations. By using the information provided, the user assumes all risks in con- nection with such use.

MAINTENANCE AND REPAIRS

Contact your local dealer for service or required maintenance. Please record the model number, serial number, voltage and purchase & Installation Information in the area below and have it ready when you call to ensure a faster service.

Model No.:

Serial No.:

Voltage:

1-Phase or 3 Phase:

Purchased From:

Location:

Purchase Date:

Installed Date:

Page 3

PROBLEMS, QUESTIONS or CONCERNS

Before you proceed consult you authorized Lang service agent directory

Call the Lang Technical Service & Parts Department at (314) 678-6315

TABLE OF CONTENTS

Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3

Equipment Description . . . . . . . . . . . . . . . . . . . . . . . . 4

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation

Ventilation & Clearence . . . . . . . . . . . . . . . . . . . . . . 5

Leg Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Electrical & Gas Connection. . . . . . . . . . . . . . . . . . . . 6

Initial Start-Up

Initial Lighting Procedure . . . . . . . . . . . . . . . . . . . . . 8

Seasoning Cooking Surface . . . . . . . . . . . . . . . . . . . . 8

Operation

Setting the Griddle Temperature . . . . . . . . . . . . . . . . . 9

Suggested Times and Temperatures . . . . . . . . . . . . . . . 9

Loading the Griddle . . . . . . . . . . . . . . . . . . . . . . . . 10

Sequence of Operation

Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Maintenance

Griddle Care (Chrome Surfaces) . . . . . . . . . . . . . . . . .11

Daily Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Weekly Cleaning . . . . . . . . . . . . . . . . . . . . . . . . .12

Burner Air Shutter Adjustment . . . . . . . . . . . . . . . . . . . 12

Troubleshooting

Symptoms / Possible Causes . . . . . . . . . . . . . . . . . . . 13

Possible Causes / Test . . . . . . . . . . . . . . . . . . . . . .14

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Exploded View & Parts List . . . . . . . . . . . . . . . . . . . . . 16-27

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

NOTICE ServiceonthisoranyotherLangappliancemustbeperformedbyqualied

personnel only. Consult your Lang Authorized Service Agent Directory. You can call our tech service number (314) 678-6315 or visit our website WWW.LANGWORLD.COM for the service agent nearest you.

Page 4

16.5”

20.5”

31.4”

TOP

FRONT SIDE

4”

IL2811

EQUIPMENT SPECIFICATIONS

Model

224ZS

236ZS

248ZS

260ZS

272ZS

Height x Width x Depth*

(Not including legs)

Clearance from

combustible surface

16.4” x 24.1” x 30.4”

418mm x 613mm x 773mm 110 kg 127 kg

16.4” x 36.1” x 30.4” 368 lbs. 420 lbs.

418mm x 917mm x 773mm 167 kg 191 kg

16.4” x 48.1” x 30.4” 448 lbs. 520 lbs.

418mm x 1222mm x 773mm 204 kg 236 kg

Sides: 5”, Back: 5”

16.4” x 60.1” x 30.4” 556 lbs. 635 lbs.

418mm x 1527mm x 773mm 253 kg 289 kg

16.4” x 72.1” x 30.4” 689 lbs. 800 lbs.

418mm x 1832mm x 773mm 313 kg 364 kg

Weight

Actual Shipping

243 lbs. 280 lbs.

*= For units with a 30” Deep Griddle surface, add 7” to the overall depth of the unit.

Freight

Class

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 5

EQUIPMENT SPECIFICATIONS continued

SPECIFICATIONS

Model

224ZS-NAT X

224ZS-LP X 10 WC

236ZS-NAT X 5 WC

236ZS-LP X 10 WC

248ZS-NAT X 5 WC

248ZS-LP X 10 WC

260ZS-NAT X 5 WC

260ZS-LP X 10 WC

272ZS-NAT X 5 WC

272ZS-LP X 10 WC

NAT.

Gas

Burner

Input

27000

BTU/hr

Manifold Gas Connection (3/4” NPT)

5 WC

54,000 BTU/hr

81,000 BTU/hr

108,000 BTU/hr

135,000 BTU/hr

162,000 BTU/hr

Electrical Requirments

Voltage

115V/60Hz 0.5 1 2.0

Total

Phase

Amps /

Line

Model

224ZSD-NAT X

224ZSD-LP X 10 WC

236ZSD-NAT X 5 WC

236ZSD-LP X 10 WC

248ZSD-NAT X 5 WC

248ZSD-LP X 10 WC

260ZSD-NAT X 5 WC

260ZSD-LP X 10 WC

272ZSD-NAT X 5 WC

272ZSD-LP X 10 WC

NAT.

Gas

Burner

Input

35000

BTU/hr

Manifold Gas Connection (3/4” NPT)

5 WC

70.000 BTU/hr

105,000 BTU/hr

140,000 BTU/hr

175,000 BTU/hr

210,000 BTU/hr

Electrical Requirments

Voltage

115V/60Hz 0.5 1 2.0

Total

Phase

Amps /

Line

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 6

EQUIPMENT DESCRIPTION

Main Power Switch

Grease Drawer

Legs

Gutter

Section

Temp. Dial

Section

Power Switch

1” Griddle Surface

Exterior Construction

The griddle dimensions are 17” (43.18cm) High, 30” (76.20cm) Deep, and width is dependent on the actual model number.

The Sides, Bottom, and Rear wall are constructed of double wall stainless steel, which allows closer installation to combustible surfaces.

The stainless steel drop-down door keeps the controls cool and control area clean.

The griddle surface is made of 1” thick, highly polished steel to reduce hot and cold spots, recovery problems, warping, and ensure even heat to the edges of the griddle.

Controls

The Selectronic Griddle comes with the solid state controls which include:

• A Main Power Switch & Power Indicator for the entire unit.

• Each twelve-inch section has its own temperature selector switch that snaps into place to lock in any temperature from 175°F to 450°F (79°C to 232°C) in 25° increments.

• Each twelve-inch section of the griddle is controlled by an area sensitive RTD probe, which can sense and react to a temperature change of +/- 4°F.

Technical

• Griddle operates on either Natural gas or Propane. This must be specied when ordering. It is shipped with a Power Cord and Plug attached.

• Floor space required is 30” (76.20cm) Deep, and width is 2 ft, 3ft, 4ft, 5ft, or 6ft depending on actual model number.

• The griddle weighs 260, 390, 520, 650, 780 lbs. depending on actual model number.

GriddleGasandVoltageSpecications

The Lang Model can be connected to any 120 Volt source. The gas and electrical specications are listed in the table on the previous page.

NOTICE The data plate is on the right side of the griddle. The oven voltage,

wattage,serialnumber,wiresize,andclearancespecicationsare

on the data plate. This information should be carefully read and understood before proceeding with the installation.

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 7

CAUTION

UNPACKING

Receiving the Griddle

Upon receipt, check for freight damage, both visible and concealed. Visible damage should be noted on the freight bill at the time of delivery and signed by the carrier’s agent. Concealed loss or damage means it does not become apparent until the merchandise has been unpacked. If concealed loss or damage is discovered upon unpacking, make a written request for inspection by the carrier’s agent within 15 days of delivery. All packing material should be kept for inspection. Do not return damaged

merchandise to Star Manufacturing Company. File your claim with the carrier.

Location

Prior to un-crating, move the oven as near to its intended location as practical. The crating will help protect the unit from the physical damage normally associated with moving it through hallways and doorways.

Un-crating

The griddle will arrive completely assembled inside a wood frame and strapped to a skid. Cut the straps and remove the wood frame.

The oven can now be removed from the skid.

THE UNIT IS EXTREMELY HEAVY. FOR SAFE HANDLING, INSTALLER SHOULD OBTAIN HELP AS NEEDED, OR EMPLOY APPROPRIATE MATERIALS HANDLING EQUIPMENT (SUCH AS A FORKLIFT, DOLLY, OR PALLET JACK) TO REMOVE THE UNIT FROM THE SKID AND MOVE IT TO THE PLACE OF INSTALLATION.

ANY STAND, COUNTER OR OTHER DEVICE ON WHICH OVEN WILL BE LOCATED MUST BE DESIGNED TO SUPPORT THE WEIGHT OF THE GRIDDLE.

SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK WHEN CUT.

VENTILATION & CLEARENCE

CLEARANCE

For use on non-combustible countertops only. Combustible and non-combustible material must be at least 48” (120cm) from the top of the appliance and 5” (150mm) from the sides and back. Adequate clearance should also be provided for proper operation and servicing.

AIR SUPPLY

Make certain not to obstruct the  ow of combustion and ventilation air. Provisions for adequate air supply must be furnished. The legs supplied with the unit must be installed. Make certain that air intake openings in the bottom of the appliance are not obstructed. They are essential for proper combustion and operation of the appliance.

EXHAUST CANOPY

It is essential that facilities be provided over the griddle to carry off fumes and gases. However, the unit should not be directly connected to a  ue or stack.

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 8

INSTALLATION

Leg Installation

There are four, adjustable legs provided for Enviro-Zone griddles.

The legs are shipped in the grease drawer(s) of the griddle. Install them into the threaded holes on the underside of the griddle body.

Leveling adjustment may be done by screwing the bottom portion of the leg in and out.

Electrical Connection

The griddle is supplied with a cord and plug. The receptacle is not provided with the griddle.

Follow the receptacle manufacturer’s instructions when connecting the receptacle to the power supply.

Gas Connection

This griddle is manufactured for use with the type of gas indicted on the nameplate. Contact the factory if your type of gas does not match the nameplate data.

All gas connectors must be in accordance with local codes and comply with the National Fuel Federal Gas Codes ANSI Z223.1 latest edition.

This appliance should be installed with a separate gas valve in the gas line ahead of the unit. Use a 3/4 inch or larger gas supply line.

Remove the 5/16 inch nuts securing the rear of burners. These nuts are for securing the main burners during transportation only. The rear burner shield must be removed to gain access to the nuts.

A pressure regulator for the type of gas specied is supplied with each appliance.

This regulator must be installed in the gas supply line. (Note the direction of the gas ow arrow.) The pressure in the manifold of the appliance should be tested with a manometer and the regulator adjusted for proper pressure with the appliance operating at full re. A 1/8 inch NPT tap is provided in the manifold for connecting a manometer.

Correct manifold pressures are: 5 inches water column for natural gas 10 inches water column for propane

When replacing the plug in the manifold, a pipe joint compound or sealant should be used that is resistant to the action of liquid petroleum gas.

Initial adjustments are the responsibility of the installer and are not chargeable to Lang Manufacturing.

After the griddle is in its nal position, adjust the legs to create 1/8 inch slant from back to front. This will allow the grease to run into the grease gutter and provide the proper combustion air for the burners.

Above: typical leg installation

IL2804

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 9

INSTALLATION continued

DANGER: THIS APPLIANCE MUST BE GROUNDED AT THE TERMINAL PROVIDED.

FAILURE TO GROUND THE APPLIANCE COULD RESULT IN ELECTROCUTION AND DEATH.

INSTALLATION OF THE UNIT MUST BE DONE BY PERSONNEL QUALIFIED TO

WORK WITH ELECTRICITY AND PLUMBING. IMPROPER INSTALLATION CAN

WARNING

CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT. UNIT MUST BE INSTALLED IN ACCORDANCE WITH ALL APPLICABLE CODES.

NOTICE: The data plate is located inside the control compartment of each griddle.

Thegriddlevoltage,serialnumber,gasspecications,andclearance specicationsareonthedataplate.Thisinformationshouldbecarefullyread

and understood before proceeding with the installation.

NOTICE: The installation of any components such as a vent hood, grease extractors,

reextinguishersystems,mustconformtotheirapplicableNational,Stateand

locally recognized installation standards.

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 10

INITIAL START UP

Initial Lighting Procedure

Clean the preservative coating from the griddle plate and splash guard. Add a mild detergent to hot water and wash the griddle plate and splash guard. Rinse with a damp sponge and dry with a clean rag.

WARNING: BEFORE LIGHTING, USE A SOAP AND WATER SOLUTION TO

TEST ALL JOINTS FOR GAS LEAKS.

• Plug the unit into a 115-volt power supply.

• Turn the ON-STANDBY toggle switch to ON.

• Set the temperature dials to the desired temperature.

• Turn the toggle switch to each section to ON.

• To turn the griddle off, simply turn the main toggle switch to STANDBY.

Seasoning the Griddle Plate (non chrome only)

• Set the temperature dials to 300°F (148°C).

• Observe the burners through the opening at the top of the control panel.

• When the burners go OFF, apply a thin coat of high-grade, non-salted vegetable oil to the griddle surface.

• Rub the oil into the griddle surface with the at side of a spatula or a towel.

• Recoat any dry spots that appear then wait two minutes and wipe off any excess oil.

• Repeat the seasoning process at 350°F (176°C) and at 400°F (204°C).

NOTICE: Duringtherstfewhoursofoperationyoumaynoticeasmall

amount of smoke coming off the griddle, and a faint odor from the smoke. This is normal for a new griddle and will disappear

aftertherstfewhoursofuse.

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 11

OPERATION

Setting the Griddle Temperature

The suggested time and temperature chart (below) is provided as a guide for the products listed only.

If different temperature settings are to be used, select one side of the griddle and operate at the lowest temperature. Adjoining sections should be set at progressively higher temperatures. Do not try to operate the end sections hot and the center sections cool.

ALWAYS KEEP THE AREA NEAR THE APPLIANCE FREE FROM

COMBUSTIBLE MATERIALS.

KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN AND DRY. IF

CAUTION

SPILLS OCCUR, CLEAN IMMEDIATELY, TO AVOID THE DANGER OF SLIPS OR FALLS.

SUGGESTED TIMES AND TEMPERATURES

TEMPERATURE

PRODUCTS

HAMBURGER

2 patties per LB 6 to 8

4 patties per LB 4 to 6

6 patties per LB 3 to 4

(F / C) TIME (MIN)

350°F (176°C)

STEAKS

1/2 to 3/4 inch thick, cooked

medium

3/4 to 1 inch thick, cooked

medium 8 to 10

Lamb Chops

Pork Chops 6 to 8

Salmon 6 to 8

Halibut

Snapper 6 to 8

Hashbrown Potatoes 375°F (190°C) 3 to 4

Bacon

Sausage Links or Patties 3 to 4

Ham (Pre-cooked) 375°F (190°C) 2

Eggs 275°F (135°C) 2 to 4

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Note: The times and temperatures in this chart are intended as a general

guide and starting point. Your actual times and temperatures may vary from

this chart.

375°F (190°C)

350°F (176°C)

325°F (162°C)

350°F (176°C)

5 to 7

6 to 8

3 to 4

Page 12

OPERATION

Loading the Griddle

An understanding of how the griddle sections are controlled will be a valuable aid in loading your griddle.

Each 12 inch section of your griddle is independently controlled. The temperature control sensor is mounted under the griddle plate in the center of each cooking section.

If the product is loaded directly over the temperature sensor, that section will turn on and the burner will heat the entire cooking section. If the product is loaded to the side, front or back of the temperature sensor, the thermostat will react to the temperature change much slowly.

During slow periods with minimal loads, do not load directly over the thermostat sensors as this will unnecessarily turn the burners on and overheat the remainder of the section not being utilized.

Turn the product and continue cooking until it has reached its desired degree of doneness.

Remove the product from the griddle.

When reloading the griddle, rst use the griddle surface on which a previous load was not placed. This will insure you the proper griddle temperature.

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 13

SEQUENCE OF OPERATION

Power On

When the griddle is connected to 115 Volt power, the spark module for each section starts sparking. While they are sparking the solenoid valve for the pilot burners are energized.

When the individual pilot burners ignite, and the pilot ame is veried, the spark module will stop sparking. Note: The pilot burners will remain lit until the griddle is removed from power or the gas is shut off.

When the main switch is turned on, 24 Volts is applied to the temperature control circuit.

When one of the individual section’s switch is turned on, it provides power to the circuit board for that section.

The operator can now set the temperature of that section by selecting it on the temperature dial.

When the temperature on the dial is set higher than the temperature of the griddle section the circuit board will generate a “Heat call”. This call (24 VAC Signal) goes to the solenoid valve opening the valve. The pilot burner ignites the main burner.

As the griddle section temperature increases the temperature sense probe resistance increases.

When the griddle section reaches the temperature set on the selector switch, the circuit board which monitors the probe resistance will turn off the heat call and there by close the gas valve.

When the griddle temperature drops below the set temperature the circuit board generates a new heat call and the sequence repeats.

MAINTENANCE & CLEANING

Griddle Care (Chromium Surfaces)

It takes very little time and effort to keep this Industrial Chromium griddle surface sparkling clean and performing at top efciency. DO NOT allow grease to accumulate as it will carbonize and become difcult to remove. To prevent this condition the following cleaning suggestions should be followed:

1. Remove excess grease and food regularly with a 4” (100mm) wide Razor Sharp type scraper and wipe surface with a damp cloth if desired.

2. Following the scraping, for end of the day cleaning, a damp cloth and a non-silicated, nonabrasive, non-chlorinated cleaner such as Bon-Ami may be used to wipe surface clean, followed by wiping with a clean wet cloth.

3. Follow steps 2 and 3 from Griddle Care (Non-Chromium Surfaces) above.

CAUTION

1. Never use pumice, griddle stones, or abrasives on a chromium surface.

2. Never strike a chromium griddle surface with a sharp instrument or spatula edge.

3. Never use steel wool.

4. Never use commercial liquid grill cleaner on the griddle surface.

5. Abusing surface voids the warranty.

CHROME GRIDDLE SURFACE LIMITED WARRANTY EXCLUSIONS

Your Chrome griddle has been designed to give you many years of cooking reliability and requires minimum maintenance to keep the chrome surface in its original condition. All Chrome griddle surfaces are warranted for a period of 5 years against manufacturing defects to the original owner from the date of installation. This limited warranty is void if it is determined by Lang Manufacturing or one of its authorized representatives that the chrome surface has been misused or abused or

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

subjected to the following situations:

1. Improperly installed.

2. Incorrect voltage applied to Chrome units allowing the surface to overheat and discolor.

3. The misuse of any instrument or tool which scratches or makes indentations in the surface which could cause the surface to peel, ake, or chip off.

4. The use of any chemical or abrasive cleaning solution, griddle brick, stone, screen or other cleaning products which could damage and affect the performance of the chrome surface.

5. The neglect of daily routine maintenance to the chromium surface.

Page 14

MAINTENANCE & CLEANING continued

Daily Cleaning (Non chrome only)

• Empty the grease drawer daily or whenever it is 3/4 full. It is easily removed for washing.

• Keep the griddle surface clean. After each cooking load, scrape the griddle surface to remove any carbonized grease.

• Once a day or when necessary the non chrome griddle surface should be thoroughly cleaned and seasoned again. Use a griddle stone, griddle pad, or liquid cleaner. Rub with the grain of the metal, being careful not to scrape the splash guard.

• Chrome griddle surfaces can be scraped with a 4” wide Razor Sharp scrapper and wipe surface with a damp cloth.

• Following the scraping, a damp cloth and non-silicated, non-abrasive, non-chlorinated cleaner such as Bon-Ami may be used to wipe surface clean, followed by wiping with a clean wet cloth.

Weekly Cleaning (Non chrome only)

• A mild detergent with water or one of the many commercial cleaners may be used.

• Be sure to rinse thoroughly and coat the griddle with a thin lm of oil to prevent rusting, non-chrome surfaces only.

• Clean the exterior of the appliance with hot water and a mild detergent to maintain a gleaming appearance.

• Re-season the griddle plate after each cleaning, non-chrome surfaces only.

Burner Air Shutter Adjustment

• The air shutters are pre-set at the factory. However, minor adjustments may be required in the eld to accommodate differences in gas and elevation.

• To adjust the air shutters, loosen the set screw holding the air damper to the burner near the gas inlet.

• Adjust the air mixture until the burner ame just ickers on the burner. “Lift-off” or yellow ame indicates improper shutter adjustment.

• Periodically inspect and clean the air shutters to insure complete combustion.

Air Shutter

Set Screw

Burner

IL2813

WARNING: KEEP WATER AND SOLUTIONS OUT OF CONTROLS. NEVER SPRAY

WARNING

OR HOSE CONTROL CONSOLE, ELECTRICAL CONNECTIONS, ETC.

CAUTION: MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES, MUCOUS

MEMBRANES AND CLOTHING. PRECAUTIONS SHOULD BE TAKEN TO WEAR RUBBER GLOVES, GOGGLES OR FACE SHIELD AND

CAUTION

PROTECTIVE CLOTHING. CAREFULLY READ THE WARNING AND FOLLOW THE DIRECTIONS ON THE LABEL OF THE CLEANER TO BE USED.

NOTICE: Never leave a chlorine sanitizer in contact with stainless steel

surfaces longer than 10 minutes. Longer contact can cause corrosion.

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 15

TROUBLESHOOTING

Symptoms

The chart below is to assist in the troubleshooting of the griddle.

Refer to the Symptoms column to locate the type of failure then to the Possible Cause for the items to be checked.

To test for a possible cause, refer to the TEST section (on the following page) and locate the Possible Cause then refer to test to identify test procedures.

SYMPTON POSSIBLE CAUSE

Entire griddle not lighting

Power indicator is not lit

Section will not heat

Product burning

Product under done

Doesn’t ignite

• Failed regulator or plugged regulator vent

• Failed transformer

• No power to cord outlet

• Griddle unplugged from outlet

• Failed power cord or plug

• Failed power switch

• Failed pilot light

• Failed gas valve

• Failed spark module

• Failed circuit board

• Failed temperature sensor

• Plugged pilot orice

• Product is cooked too long

• Failed temperature sensor

• Failed circuit board

• Failed temperature selector

• Open wire between selector and circuit board

• Failed temperature sensor

• Failed circuit board

• Failed temperature selector

• Incorrect Gas pressure

• Failed igniter

• Improper gas pressure

• No power

• Failed spark module

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 16

TROUBLESSHOOTING CONT.

TESTS

POSSIBLE CAUSE TEST

Failed Regulator • Replace regulator

Failed transformer • Check transformer for correct voltage, replace as necessary

Failed power cord or plug • Check cord and plug for proper voltage

Failed power switch • Check switch for continuity across poles

Failed pilot light • Check for continuity across pilot light leads

Failed gas valve

Failed igniter • Replace as necessary

Failed spark module • Check for correct incoming voltage at module

Failed circuit board • Check for proper voltage and operation

Failed temperature sensor • Ohm sensor for correct resistance

Failed temperature selector • Remove the wires and check the resistance on all settings

Open wire between selector and circuit board

Incorrect gas pressure • Adjust to correct pressure

Plugged regulator vent, or orice • Clean as necessary

• Remove the wires from the valve terminals and check for continuity across the coil

• Replace as necessary

NOTICE: Service on this, or any other, LANG appliance must be performed by

qualiedpersonnelonly.ConsultyourLANGauthorizedserviceagent

directory or call the factory at (314) 678-6315, or WWW.LANGWORLD.COM For the service agent nearest you.

BOTH HIGH AND LOW VOLTAGES ARE PRESENT INSIDE THIS

APPLIANCE WHEN THE UNIT IS PLUGGED/WIRED INTO A LIVE RECEPTACLE. BEFORE REPLACING ANY PARTS, DISCONNECT THE

WARNING

UNIT FROM THE ELECTRIC POWER SUPPLY.

USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED

BY LANG OR THEIR AUTHORIZED DISTRIBUTORS CAN CAUSE BODILY INJURY TO THE OPERATOR AND DAMAGE TO THE EQUIPMENT AND

CAUTION

WILL VOID ALL WARRANTIES.

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 17

PART NO.

2M-61122-W64

W/D - 236ZS GRIDDLE (NO TIMERS)

MODEL NO.

MATERIAL

REV. DATE/ECO DESCRIPTION OF CHANGE

TITLE

REVISIONS

3/25/14 :

DATE

CK.

ADAMS :

TOLERANCE: UNLESS NOTED: .xxx ± .015

FINISH

# 10 SUNNEN DRIVE

LANG MANUFACTURING

ST. LOUIS, MO. 63143, USA

ANGLES ± 1 °

GRN

120V

BLK

WHT

GRN

WHT

BLK

WHT

BLK

WHT

24V

BLU

YEL

RED

BLK

RED

BLK

YEL

RED

BLK

WHT

BLK

WHT

YEL

RED

ORG

YEL

BRN

YEL

ORG

BLU

COM

BRN

WHT

GRN

1 2 3 4

RED

YEL

ORG

BLU

RED

BLK

2 3 4

GRN

WHT

YEL

RED

BLK

BRN

YEL

COM

BRN

RED

GRN

THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L

INC. NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

PILOT IGNITOR

PILOT IGNITION MODULE

BURNER SOLENOID

PILOT SOLENOID

POWER CORD

KEY:

ON/OFF SWITCH

RELAY

TEMP CONTROL BOARD

WIRE NUT

INDICATOR LAMP

12 POSITION SWITCH

CONTROL SWITCH

RTD

BLK

WHT

ORG

CAP UNUSED

CONNECTORS

TRANSFORMER

RED

BLU

ORG

RED

BLK

2 3 4

GRN

RED

YEL

BRN

YEL

COM

BRN

YEL

Page 18

SEE DETAIL A

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Model: EnviroZone Gas Selectronic Griddle

SK2771, Rev. - 4/14/14

Page 19

Model: 236ZS EnviroZone Selectronic Gas

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

DETAIL A

SK2771, Rev. - 4/01/14

Page 20

PARTS LIST May 20, 2014, Rev. A

Model: 224ZS-NAT & LP EnviroZone Selectronic Gas Griddle

Fig No. Part No Qty Description Application

K9-141-201-123

K9-141-201-723 GRIDDLE PLATE ASSY 2’ ZSD 224ZSD

2 2E-41100-42 2 SENSOR EZONE SELECTRONIC

K9-141-486

K9-141-486-3 PROBE GUARD, ZSD SELECT 224ZSD 4 2C-20202-08 8 WSHR PLT 5/16 LOCK SPLIT 5 2C-20301-06 10 NUT HEX 5/16-18 PLTD

K9-141-171-3W2 6

K9-141-171-W2 GRIDDLE BURNER ASSY 224ZS

K9-141-161-3W1 7

K9-141-161-W1 224ZS 8 K9-141-182 0 BAFFLE BETWEEN BURNERS

K9-141-181 9

K9-141-186 BAFFLE UNDER BURNER-30”D 224ZSD

11 2A-72500-20 4 LEG 10.25 WITH ADJ HEX 12 2A-72901-34 AR LEG STD 2 OD X 24.625 13 2C-20301-40 8 NUT HEX ACORN LOCK 3/8-16S/S 14 2C-20105-20 8 SCREW SET 3/8-16X1/2 CUP POINT 15 72901-27 4 CASTER 5 ADJ 16 2E-Z12020 1 SWITCH-TOGGLE 2P ST 17 K9-141-232-2-W2 1 FRONT PNL WELD, RIGHT ZS 18 Z1-70-07-0343 3 SWITCH GUARD 19 2M-12-07-0038 3 LABEL ON & OFF 20 2I-05-07-0013 3 BOOT SWITCH 21 Y9-31601-09-1 1 PILOT LT 120V W/TIN CLIP 22 2R-70701-28 2 KNB BLK 1/4BUSH2SETSCW@90 23 2M-60301-29 1 PNLLBL SELCT SWTDIAL 450o 24 2M-60301-43 1 DIE CAST PLT LANG SATIN 25 K9-141-241-W9 1 FRONT PANEL-LEFT END 2FT 26 2E-30600-W14 2 RELAY 277VAC SPST 30A 27 2K-70801-07 6 SPACER SUPPORT 1/2LG 28 2E-30304-22 2 SWTCB175-450oFW/41100-13 29 2E-40101-W19 2 CIRBD SI TEMP CONTROL 30 2E-30303-18 2 SWTTOGON-OFFSPST1/4HP125V 31 2K-80100-20 1 MANIFLD FR 141 GRIDDLE 2’ 32 2K-70101-03 1 BRASTBEELBOW 1/4NPT-3/8CC 33 2K-70101-06 1 BRASTEE BRNCH 1/4NPTM-3/8

35 2J-80302-W1 1 IGNITOR ELECTRODE 36 2C-Z5883 10 10-24 X 1/2 FZA SCREW 37 K9-141-146 2 PROBE GUARD SUPPORT 38 2K-70101-51 1 BRASTBE ELBOW 1/4CCX1/4CC 39 M9-144-186 1 BRACKET-IGNITOR TUBE-CB 40 2F-80002-W19 1 TUBE - LIGHTER .25 DIA

K9-141-252-W1 K9-142-251 GREASE DRAWER-WELD ASSY 224ZSD

2V-80501-04 2V-80501-05 GAS REG 3/4X3/4 CLS II LP

1 GREASE DRAWER SLIDE WELD

GRIDDLE PLATE ASSY, 2’ ZS 224ZS

PROBE GUARD, ZS SELECT 224ZS

GRIDDLE BURNER ASSY-30”D 224ZSD

224ZSD

BAFFLE UNDER BURNER 224ZS

GREASE DRAWER-EZONE GRID 224ZS

GAS REG 3/4X3/4 CLS I NAT

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 21

Model: 224ZS-NAT & LP EnviroZone Selectronic Gas Griddle

Fig No. Part No Qty Description Application

2A-45408 2A-80400-12 ORIFICE HOOD .0595 #53 224ZS-LP

42 2C-20102-08 12 SCRW PHD ST 8-32X.375 43 K9-141-156-W5 1 VALVE BRACKET LEFT 44 2C-20102-12 24 SCRW PHD ST 10-32X3/8 45 2K-45300 5 FITTING 3/8CC X 1/8NPT 46 2V-80502-W07 3 VALVE SOLENOID-1/8 NPT 47 2V-70402-06 1 VALVE PILOT 1/8NPTX1/4CC 49 2J-80300-W20 1 PILOT IGNITION CONTROL 50 2C-20102-04 2 SCRW PHD ST 8-32X.5 PLTD 51 K9-141-151-W1 1 PILOT IGN CNTL MOUNT ASSY 52 2E-31400-07 1 XFORMR120-208-240/24V40VA 53 K9-141-152-W2 1 24V XFMR BRACKET ASSY 54 2C-20301-11 2 NUT HEX 8-32 PLTD NI 2C-20602-04 2 TINNERMAN SPD NUT 1/8 DIA NI 2E-31107-02-W2 1 CORDSET 14/3 15A 120V 10’ NI 2K-Z4921 4 BURNER TUBE FLEX 3/8 OD NI 2K-Z6943 1 GAS LINE 1/4”D x 8”L NI 2M-61122-W64 AR WIRE DIAGRAM - 236ZS

2A-80404-29 ORIFICE - #51 BLACK 224ZSD-LP Y9-80400-18 ORIFICE HOOD .1065 #36 224ZSD-NAT 2A-W1185 ORIFICE FITTING - 90 DEG

ORIFICE-HOOD #42 GRID NAT 224ZS-NAT

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 22

PARTS LIST May 20, 2014, Rev. A

Model: 236ZS-NAT & LP EnviroZone Selectronic Gas Griddle

Fig No. Part No Qty Description Application

K9-141-201-133

K9-141-201-733 GRIDDLE PLATE ASSY, 3’ ZSD 236ZSD

2 2E-41100-42 3 SENSOR EZONE SELECTRONIC

K9-141-486

K9-141-486-3 PROBE GUARD ZSD SELECT 236ZSD 4 2C-20202-08 12 WSHR PLT 5/16 LOCK SPLIT 5 2C-20301-06 14 NUT HEX 5/16-18 PLTD

K9-141-171-3W2 6

K9-141-171-W2 GRIDDLE BURNER ASSY 236ZS

K9-141-161-3W1 7

K9-141-161-W1 236ZS

K9-141-182 8

K9-141-187 236ZSD

K9-141-181 9

K9-141-186 BAFFLE UNDER BURNER-30”D 236ZSD

11 2A-72500-20 4 LEG 10.25 WITH ADJ HEX 12 2A-72901-34 AR LEG STD 2 OD X 24.625 13 2C-20301-40 8 NUT HEX ACORN LOCK 3/8-16S/S 14 2C-20105-20 8 SCREW SET 3/8-16X1/2 CUP POINT 15 72901-27 4 CASTER 5 ADJ 16 2E-Z12020 1 SWITCH-TOGGLE 2P ST 17 K9-141-246-W8 1 FRONT PNL WELD, RIGHT ZS 18 Z1-70-07-0343 4 SWITCH GUARD 19 2M-12-07-0038 4 LABEL ON & OFF 20 2I-05-07-0013 4 BOOT SWITCH 21 Y9-31601-09-1 1 PILOT LT 120V W/TIN CLIP 22 2R-70701-28 3 KNB BLK 1/4BUSH2SETSCW@90 23 2M-60301-29 3 PNLLBL SELCT SWTDIAL 450o 24 2M-60301-43 1 DIE CAST PLT LANG SATIN 25 K9-141-241-W9 1 FRONT PANEL-LEFT END 2FT 26 2E-30600-W14 3 RELAY 277VAC SPST 30A 27 2K-70801-07 9 SPACER SUPPORT 1/2LG 28 2E-30304-22 3 SWTCB175-450oFW/41100-13 29 2E-40101-W19 3 CIRBD SI TEMP CONTROL 30 2E-30303-18 3 SWTTOGON-OFFSPST1/4HP125V 31 2K-80100-21 1 MANIFLD FR 141 GRIDDLE 3’ 32 2K-70101-03 1 BRASTBEELBOW 1/4NPT-3/8CC 33 2K-70101-06 2 BRASTEE BRNCH 1/4NPTM-3/8

35 2J-80302-W1 2 IGNITOR ELECTRODE 36 2C-Z5883 18 10-24 X 1/2 FZA SCREW 37 K9-141-146 3 PROBE GUARD SUPPORT 38 2K-70101-51 2 BRASTBE ELBOW 1/4CCX1/4CC 39 M9-144-186 2 BRACKET-IGNITOR TUBE-CB 40 2F-80002-W19 2 TUBE - LIGHTER .25 DIA

K9-141-252-W1

K9-142-251 GREASE DRAWER -WELD ASSY 236ZSD

2V-80501-04

2V-80501-05 GAS REG 3/4X3/4 CLS II LP

1 GREASE DRAWER SLIDE WELD

1 BAFFLE BETWEEN BURNERS

GRIDDLE PLATE ASSY, 3’ ZS 236ZS

PROBE GUARD, ZS SELECT 236ZS

GRIDDLE BURNER ASSY-30”D 236ZSD

236ZSD

236ZS

BAFFLE UNDER BURNER 236ZS

GREASE DRAWER-EZONE GRID 236ZS

GAS REG 3/4X3/4 CLS I NAT

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 23

Model: 236ZS-NAT & LP EnviroZone Selectronic Gas Griddle

Fig No. Part No Qty Description Application

2A-45408 2A-80400-12 ORIFICE HOOD .0595 #53 236ZS-LP

42 2C-20102-08 20 SCRW PHD ST 8-32X.375 43 K9-141-156-W5 2 VALVE BRACKET LEFT 44 2C-20102-12 31 SCRW PHD ST 10-32X3/8 45 2K-45300 8 FITTING 3/8CC X 1/8NPT 46 2V-80502-W07 5 VALVE SOLENOID-1/8 NPT 47 2V-70402-06 2 VALVE PILOT 1/8NPTX1/4CC

NI 2C-20602-04 2 TINNERMAN SPD NUT 1/8 DIA NI 2E-31107-02-W2 1 CORDSET 14/3 15A 120V 10’ NI 2K-Z4921 5 BURNER TUBE FLEX 3/8 OD NI 2K-Z6943 2 GAS LINE 1/4”D x 8”L NI 2M-61122-W64 AR WIRE DIAGRAM - 236ZS

2A-80404-29 ORIFICE - #51 BLACK 236ZSD-LP Y9-80400-18 ORIFICE HOOD .1065 #36 236ZSD-NAT 2A-W1185 ORIFICE FITTING - 90 DEG

K9-141-156-W4 K9-141-156-W6 VALVE BRACKET-SHORT RIGHT

ORIFICE-HOOD #42 GRID NAT 236ZS-NAT

VALVE BRACKET RIGHT

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 24

PARTS LIST May 20, 2014, Rev. A

Model: 248ZS-NAT & LP EnviroZone Selectronic Gas Griddle

Fig No. Part No Qty Description Application

2 2E-41100-42 4 SENSOR EZONE SELECTRONIC

4 2C-20202-08 16 WSHR PLT 5/16 LOCK SPLIT 5 2C-20301-06 18 NUT HEX 5/16-18 PLTD

11 2A-72500-20 4 LEG 10.25 WITH ADJ HEX 12 2A-72901-34 AR LEG STD 2 OD X 24.625 13 2C-20301-40 8 NUT HEX ACORN LOCK 3/8-16S/S 14 2C-20105-20 8 SCREW SET 3/8-16X1/2 CUP POINT 15 2P-72901-33 4 CASTER 5 ADJ 16 2E-Z12020 1 SWITCH-TOGGLE 2P ST

18 Z1-70-07-0343 5 SWITCH GUARD 19 2M-12-07-0038 5 LABEL ON & OFF 20 2I-05-07-0013 5 BOOT SWITCH 21 Y9-31601-09-1 1 PILOT LT 120V W/TIN CLIP 22 2R-70701-28 4 KNB BLK 1/4BUSH2SETSCW@90 23 2M-60301-29 3 PNLLBL SELCT SWTDIAL 450o 24 2M-60301-43 1 DIE CAST PLT LANG SATIN 25 K9-141-241-W9 1 FRONT PANEL-LEFT END 2FT 26 2E-30600-W14 4 RELAY 277VAC SPST 30A 27 2K-70801-07 12 SPACER SUPPORT 1/2LG 28 2E-30304-22 4 SWTCB175-450oFW/41100-13 29 2E-40101-W19 4 CIRBD SI TEMP CONTROL 30 2E-30303-18 4 SWTTOGON-OFFSPST1/4HP125V 31 2K-80100-22 1 MANIFLD FR 141 GRIDDLE 4’ 32 2K-70101-03 2 BRASTBEELBOW 1/4NPT-3/8CC 33 2K-70101-06 2 BRASTEE BRNCH 1/4NPTM-3/8

35 2J-80302-W1 2 IGNITOR ELECTRODE 36 2C-Z5883 20 10-24 X 1/2 FZA SCREW 37 K9-141-146 4 PROBE GUARD SUPPORT 38 2K-70101-51 2 BRASTBE ELBOW 1/4CCX1/4CC 39 M9-144-186 2 BRACKET-IGNITOR TUBE-CB 40 2F-80002-W19 2 TUBE - LIGHTER .25 DIA

K9-141-201-143 K9-141-201-743 GRIDDLE PLATE ASSY, 4’ ZSD 248ZSD

K9-141-486 K9-141-486-3 PROBE GUARD, ZSD SELECT 248ZSD

K9-141-171-3W2 K9-141-171-W2 GRIDDLE BURNER ASSY 248ZS K9-141-161-3W1 K9-141-161-W1 248ZS K9-141-182 K9-141-187 BAFFLE BETWEEN BURNERS 30”D 248ZSD K9-141-181 K9-141-186 BAFFLE UNDER BURNER-30”D 248ZSD K9-141-252-W1 K9-142-251 GREASE DRAWER WELD ASSY 248ZSD

K9-141-232-2-W2 K9-141-232-6-W3 FRONT PNL WELD, CENTER ZS

2V-80501-04 2V-80501-05 GAS REG 3/4X3/4 CLS II LP

2 GREASE DRAWER SLIDE WELD

GRIDDLE PLATE ASSY, 4’ ZS 248ZS

PROBE GUARD, ZS SELECT 248ZS

GRIDDLE BURNER ASSY-30”D 248ZSD

248ZSD

BAFFLE BETWEEN BURNERS 248ZS

BAFFLE UNDER BURNER 248ZS

GREASE DRAWER-EZONE GRID 248ZS

FRONT PNL WELD, RIGHT ZS

GAS REG 3/4X3/4 CLS I NAT

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 25

Model: 248ZS-NAT & LP EnviroZone Selectronic Gas Griddle

Fig No. Part No Qty Description Application

2A-45408 2A-80400-12 ORIFICE-HOOD .0595 #53 248ZS-LP

42 2C-20102-08 24 SCRW PHD ST 8-32X.375 43 K9-141-156-W5 2 VALVE BRACKET LEFT 44 2C-20102-12 40 SCRW PHD ST 10-32X3/8 45 2K-45300 10 FITTING 3/8CC X 1/8NPT 46 2V-80502-W07 6 VALVE SOLENOID-1/8 NPT 47 2V-70402-06 2 VALVE PILOT 1/8NPTX1/4CC

49 2J-80300-W20 2 PILOT IGNITION CONTROL 50 2C-20102-04 4 SCRW PHD ST 8-32X.5 PLTD 51 K9-141-151-W1 2 PILOT IGN CNTL MOUNT ASSY 52 2E-31400-07 1 XFORMR120-208-240/24V40VA 53 K9-141-152-W2 1 24V XFMR BRACKET ASSY 54 2C-20301-11 2 NUT HEX 8-32 PLTD NI 2C-20602-04 2 TINNERMAN SPD NUT 1/8 DIA NI 2E-31107-02-W2 1 CORDSET 14/3 15A 120V 10’ NI 2K-Z4921 6 BURNER TUBE FLEX 3/8 OD NI 2K-Z6943 GAS LINE 1/4”D x 8”L NI 2M-61122-W64 AR WIRE DIAGRAM - 236ZS

2A-80404-29 ORIFICE - #51 BLACK 248ZSD-LP Y9-80400-18 ORIFICE HOOD .1065 #36 248ZSD-NAT 2A-W1185 ORIFICE FITTING - 90 DEG

K9-141-156-W4 3 VALVE BRACKET RIGHT K9-141-156-W6 1 VALVE BRACKET-SHORT RIGHT

ORIFICE-HOOD #42 GRID NAT 248ZS-NAT

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 26

PARTS LIST May 20, 2014, Rev. A

Model: 260ZS-NAT & LP EnviroZone Selectronic Gas Griddle

Fig No. Part No Qty Description Application

K9-141-201-153

K9-141-201-753 GRIDDLE PLATE ASSY, 5’ ZSD 260ZSD

2 2E-41100-42 5 SENSOR EZONE SELECTRONIC

K9-141-486

K9-141-486-3 PROBE GUARD, ZSD SELECT 260ZSD 4 2C-20202-08 20 WSHR PLT 5/16 LOCK SPLIT 5 2C-20301-06 22 NUT HEX 5/16-18 PLTD

K9-141-171-3W2 6

K9-141-171-W2 GRIDDLE BURNER ASSY 260ZS

K9-141-161-3W1 7

K9-141-161-W1 260ZS

K9-141-182 8

K9-141-187 BAFFLE-BETWEEN BURNERS 30”D 260ZSD

K9-141-181 9

K9-141-186 BAFFLE UNDER BURNER-30”D 260ZSD

18 Z1-70-07-0343 6 SWITCH GUARD 19 2M-12-07-0038 6 LABEL ON & OFF 20 2I-05-07-0013 6 BOOT SWITCH 21 Y9-31601-09-1 1 PILOT LT 120V W/TIN CLIP 22 2R-70701-28 5 KNB BLK 1/4BUSH2SETSCW@90 23 2M-60301-29 4 PNLLBL SELCT SWTDIAL 450o 24 2M-60301-43 1 DIE CAST PLT LANG SATIN 25 K9-141-241-W9 1 FRONT PANEL-LEFT END 2FT 26 2E-30600-W14 5 RELAY 277VAC SPST 30A 27 2K-70801-07 15 SPACER SUPPORT 1/2LG 28 2E-30304-22 5 SWTCB175-450oFW/41100-13 29 2E-40101-W19 5 CIRBD SI TEMP CONTROL 30 2E-30303-18 5 SWTTOGON-OFFSPST1/4HP125V 31 2K-80100-23 1 MANIFLD FR 141 GRIDDLE 5’ 32 2K-70101-03 2 BRASTBEELBOW 1/4NPT-3/8CC 33 2K-70101-06 3 BRASTEE BRNCH 1/4NPTM-3/8

35 2J-80302-W1 3 IGNITOR ELECTRODE 36 2C-Z5883 28 10-24 X 1/2 FZA SCREW 37 K9-141-146 5 PROBE GUARD SUPPORT 38 2K-70101-51 3 BRASTBE ELBOW 1/4CCX1/4CC 39 M9-144-186 3 BRACKET-IGNITOR TUBE-CB 40 2F-80002-W19 3 TUBE - LIGHTER .25 DIA

K9-141-252-W1

K9-142-251 GREASE DRAWER-WELD ASSY 260ZSD

K9-141-232-2-W2

K9-141-232-5-W2 FRONT PNL WELD, CENTER ZS

2V-80501-04

2V-80501-05 GAS REG 3/4X3/4 CLS II LP

2 GREASE DRAWER SLIDE WELD

GRIDDLE PLATE ASSY, 5’ ZS 260ZS

PROBE GUARD, ZS SELECT 260ZS

GRIDDLE BURNER ASSY-30”D 260ZSD

260ZSD

BAFFLE BETWEEN BURNERS 260ZS

BAFFLE UNDER BURNER 260ZS

GREASE DRAWER-EZONE GRID 260ZS

FRONT PNL WELD, RIGHT ZS

GAS REG 3/4X3/4 CLS I NAT

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 27

Model: 260ZS-NAT & LP EnviroZone Selectronic Gas Griddle

Fig No. Part No Qty Description Application

2A-45408 2A-80400-12 ORIFICE HOOD .0595 #53 260ZS-LP

42 2C-20102-08 32 SCRW PHD ST 8-32X.375 43 K9-141-156-W5 2 VALVE BRACKET LEFT 44 2C-20102-12 46 SCRW PHD ST 10-32X3/8 45 2K-45300 13 FITTING 3/8CC X 1/8NPT 46 2V-80502-W07 8 VALVE SOLENOID-1/8 NPT 47 2V-70402-06 3 VALVE PILOT 1/8NPTX1/4CC

49 2J-80300-W20 3 PILOT IGNITION CONTROL 50 2C-20102-04 6 SCRW PHD ST 8-32X.5 PLTD 51 K9-141-151-W1 3 PILOT IGN CNTL MOUNT ASSY 52 2E-31400-07 1 XFORMR120-208-240/24V40VA 53 K9-141-152-W2 1 24V XFMR BRACKET ASSY 54 2C-20301-11 2 NUT HEX 8-32 PLTD NI 2C-20602-04 2 TINNERMAN SPD NUT 1/8 DIA NI 2E-31107-02-W2 1 CORDSET 14/3 15A 120V 10’ NI 2K-Z4921 8 BURNER TUBE FLEX 3/8 OD NI 2K-Z6943 3 GAS LINE 1/4”D x 8”L NI 2M-61122-W64 AR WIRE DIAGRAM - 236ZS

2A-80404-29 ORIFICE - #51 BLACK 260ZSD-LP Y9-80400-18 ORIFICE HOOD .1065 #36 260ZSD-NAT 2A-W1185 ORIFICE FITTING - 90 DEG

K9-141-156-W4 K9-141-156-W6 VALVE BRACKET-SHORT RIGHT

ORIFICE-HOOD #42 GRID NAT 260ZS-NAT

VALVE BRACKET RIGHT

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 28

PARTS LIST May 20, 2014, Rev. A

Model: 272ZS-NAT & LP EnviroZone Selectronic Gas Griddle

Fig No. Part No Qty Description Application

K9-141-201-163

K9-141-201-763 GRIDDLE PLATE ASSY, 6’ ZSD 272ZSD

2 2E-41100-42 6 SENSOR EZONE SELECTRONIC

K9-141-486

K9-141-486-3 PROBE GUARD, ZSD SELECT 272ZSD 4 2C-20202-08 24 WSHR PLT 5/16 LOCK SPLIT 5 2C-20301-06 26 NUT HEX 5/16-18 PLTD

K9-141-171-3W2 6

K9-141-171-W2 GRIDDLE BURNER ASSY 272ZS

K9-141-161-3W1 7

K9-141-161-W1 242ZS

K9-141-182 8

K9-141-187 BAFFLE-BETWEEN BURNERS 30”D 272ZSD

K9-141-181 9

K9-141-186 BAFFLE UNDER BURNER-30”D 272ZSD

18 Z1-70-07-0343 7 SWITCH GUARD 19 2M-12-07-0038 7 LABEL ON & OFF 20 2I-05-07-0013 7 BOOT SWITCH 21 Y9-31601-09-1 1 PILOT LT 120V W/TIN CLIP 22 2R-70701-28 6 KNB BLK 1/4BUSH2SETSCW@90 23 2M-60301-29 6 PNLLBL SELCT SWTDIAL 450o 24 2M-60301-43 1 DIE CAST PLT LANG SATIN 25 K9-141-242-W8 1 FRONT PANEL WELD, LEFT ZS 26 2E-30600-W14 6 RELAY 277VAC SPST 30A 27 2K-70801-07 9 SPACER SUPPORT 1/2LG 28 2E-30304-22 6 SWTCB175-450oFW/41100-13 29 2E-40101-W19 6 CIRBD SI TEMP CONTROL 30 2E-30303-18 6 SWTTOGON-OFFSPST1/4HP125V 31 2K-80100-24 1 MANIFLD FR 141 GRIDDLE 6’ 32 2K-70101-03 3 BRASTBEELBOW 1/4NPT-3/8CC 33 2K-70101-06 2 BRASTEE BRNCH 1/4NPTM-3/8

35 2J-80302-W1 2 IGNITOR ELECTRODE 36 2C-Z5883 18 10-24 X 1/2 FZA SCREW 37 K9-141-146 6 PROBE GUARD SUPPORT 38 2K-70101-51 2 BRASTBE ELBOW 1/4CCX1/4CC 39 M9-144-186 2 BRACKET-IGNITOR TUBE-CB 40 2F-80002-W19 2 TUBE - LIGHTER .25 DIA

K9-141-252-W1

K9-142-251 GREASE DRAWER-WELD ASSY 272ZSD

K9-141-237-W13

K9-141-246-W8 FRONT PANEL WELD, RIGHT ZS

2V-80501-04

2V-80501-05 GAS REG 3/4X3/4 CLS II LP

GRIDDLE PLATE ASSY, 6’ ZS 272ZS

PROBE GUARD, ZS SELECT 272ZS

GRIDDLE BURNER ASSY-30”D 272ZSD

1 GREASE DRAWER SLIDE WELD

BAFFLE BETWEEN BURNERS 272ZS

BAFFLE UNDER BURNER 272ZS

GREASE DRAWER-EZONE GRID 272ZS

FRONT PANEL, CENTER ZS

GAS REG 3/4X3/4 CLS I NAT

272ZSD

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 29

Model: 272ZS-NAT & LP EnviroZone Selectronic Gas Griddle

Fig No. Part No Qty Description Application

2A-45408 2A-80400-12 ORIFICE HOOD .0595 #53 272ZS-LP

42 2C-20102-08 36 SCRW PHD ST 8-32X.375 43 K9-141-156-W5 0 VALVE BRACKET LEFT 44 2C-20102-12 50 SCRW PHD ST 10-32X3/8 45 2K-45300 8 FITTING 3/8CC X 1/8NPT 46 2V-80502-W07 9 VALVE SOLENOID-1/8 NPT 47 2V-70402-06 2 VALVE PILOT 1/8NPTX1/4CC

49 2J-80300-W20 2 PILOT IGNITION CONTROL 50 2C-20102-04 4 SCRW PHD ST 8-32X.5 PLTD 51 K9-141-151-W1 2 PILOT IGN CNTL MOUNT ASSY 52 2E-31400-07 1 XFORMR120-208-240/24V40VA 53 K9-141-152-W2 1 24V XFMR BRACKET ASSY 54 2C-20301-11 2 NUT HEX 8-32 PLTD NI 2C-20602-04 2 TINNERMAN SPD NUT 1/8 DIA NI 2E-31107-02-W2 1 CORDSET 14/3 15A 120V 10’ NI 2K-Z4921 9 BURNER TUBE FLEX 3/8 OD NI 2K-Z6943 2 GAS LINE 1/4”D x 8”L NI 2M-61122-W64 AR WIRE DIAGRAM - 236ZS

2A-80404-29 ORIFICE - #51 BLACK 272ZSD-LP Y9-80400-18 ORIFICE HOOD .1065 #36 272ZSD-NAT 2A-W1185 ORIFICE FITTING - 90 DEG

K9-141-156-W4 4 VALVE BRACKET RIGHT K9-141-156-W6 5 VALVE BRACKET-SHORT RIGHT

ORIFICE-HOOD #42 GRID NAT 272ZS-NAT

2M-W2014: GAS ENVIROZONE SELECTRONIC GRIDDLE

Page 30

Page 31

Page 32

STAR INTERNATIONAL HOLDINGS INC. COMPANY

Star - Holman - Lang - Wells - Bloomeld - Toastmaster

10 Sunnen Drive, St. Louis, MO 63143 U.S.A.

(314) 678-6303

www.star-mfg.com