Lang 224S-NAT User Manual

SELECTRONIC

GAS GRIDDLE

Commercial

224S, 224SC

236S, 236SC 236SCHG, 236SHE, 236SHG

248S, 248SHE, 248SHG, 260S, 272S

Installation and

Operation

Instructions

2M-W360 Rev. J 3/03/15

248S

IL1576

1

SAFETY SYMBOL

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN

The installation of the Appliance must conform to the NATIONAL FUEL GAS CODE "ANSI Z223.1 - LATEST
EDITION" AND ALL LOCAL GAS COMPANY RULES AND REGULATIONS.

IN CANADA INSTALLATION SHALL BE IN ACCORDANCE WITH THE CURRENT CAN/CGA-B149.1 NATURAL
GAS INSTALLATION CODE OR CAN/CGA-B149.2 PROPANE INSTALLATION CODE AND LOCAL CODES WHERE

APPLICABLE.

INSTRUCTIONS TO BE FOLLOWED IN THE EVENT USER SMELLS GAS. THIS INFORMATION

SHALL BE OBTAINED BY CONSULTING YOUR LOCAL GAS SUPPLIER. AS A MINIMUM, TURN

OFF THE GAS AND CALL YOUR GAS COMPANY AND YOUR AUTHORIZED SERVICE AGENT.

IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN

CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATION

& MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS

These symbols are intended to alert the user to the presence of important operating
and maintenance instructions in the manual accompanying the appliance.

FOR YOUR SAFTEY

THE VICINTIY OF THIS OR ANY OTHER APPLIANCE.

POST IN PROMINENT LOCATION

EVACUATE ALL PERSONNEL FROM THE AREA.

WARNING

EQUIPMENT.

WARNING

RISK OF FIRE OR ELECTRIC SHOCK

DO NOT OPEN

WARNING, TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE

CONTROL PANEL. NO USER-SERVICABLE PARTS INSIDE.
REPAIRS SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY.

NOTICE

Using any part other than genuine Lang factory supplied parts relieves the manufacturer of all liability.

Lang reserves the right to change speci cations and product design without notice. Such
revisions do not entitle the buyer to corresponding changes, improvements, additions or
replacements for previously purchased equipment.

Due to periodic changes in designs, methods, procedures, policies and regulations, the
specifications contained in this sheet are subject to change without notice. While Lang
Manufacturing exercises good faith efforts to provide information that is accurate, we are
not responsible for errors or omissions in information provided or conclusions reached as a
result of using the speci cations. By using the information provided, the user assumes all risks in con-
nection with such use.

MAINTENANCE AND REPAIRS

Contact your local dealer for service or required maintenance. Please record the model number, serial
number, voltage and purchase & Installation Information in the area below and have it ready when you
call to ensure a faster service.

Model No.:

Serial No.:

Voltage:

1-Phase or 3 Phase:

Purchased From:

Location:

Purchase Date:

Installed Date:

2

PROBLEMS, QUESTIONS or CONCERNS

Before you proceed consult you authorized Lang service agent directory

or

Call the Lang Technical Service & Parts Department at [phone]

TABLE OF CONTENTS

Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5

Equipment Description . . . . . . . . . . . . . . . . . . . . . . . . 6

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation

Ventilation & Clearence . . . . . . . . . . . . . . . . . . . . . . 7

Electrical & Gas Connection. . . . . . . . . . . . . . . . . . . . 8

Initial Start-Up

Initial Lighting Procedure . . . . . . . . . . . . . . . . . . . . . 9

Seasoning Cooking Surface . . . . . . . . . . . . . . . . . . . . 9

Operation

Setting the Griddle Temperature . . . . . . . . . . . . . . . . .10

Suggested Times and Temperatures . . . . . . . . . . . . . . .10

Loading the Griddle . . . . . . . . . . . . . . . . . . . . . . . . 11

Sequence of Operation

Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Maintenance

Daily Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Weekly Cleaning . . . . . . . . . . . . . . . . . . . . . . . . .13

Burner Air Shutter Adjustment . . . . . . . . . . . . . . . . . . . 13

Troubleshooting

Symptoms / Possible Causes . . . . . . . . . . . . . . . . . . . 14

Possible Causes / Test . . . . . . . . . . . . . . . . . . . . . .15

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Exploded View & Parts List . . . . . . . . . . . . . . . . . . . . . 20-27

NOTICE ServiceonthisoranyotherLangappliancemustbeperformedbyqualied

personnel only. Consult your Lang Authorized Service Agent Directory.
You can call our tech service number [phone] or visit our website
WWW.LANGWORLD.COM for the service agent nearest you.

3

16.4”

4.0”

20.4”

30.4”

W”

Top

Front Side

IL1577

EQUIPMENT SPECIFICATIONS

Model

224S

236S

248S

260S

272S

Height x Width x Depth Clearance from Weight

16.4” x 24.1” x 30.4” 243 lbs. 280 lbs.

418mm x 613mm x 773mm 110 kg 127 kg

16.4” x 36.1” x 30.4” 368 lbs. 420 lbs.

418mm x 917mm x 773mm 167 kg 191 kg

16.4” x 48.1” x 30.4” Sides: 5” 448 lbs. 520 lbs.

418mm x 1222mm x 773mm Back: 5” 204 kg 236 kg

16.4” x 60.1” x 30.4” 556 lbs. 635 lbs.

418mm x 1527mm x 773mm 253 kg 289 kg

16.4” x 72.1” x 30.4” 689 lbs. 800 lbs.

418mm x 1832mm x 773mm 313 kg 364 kg

Freight

Class(Not including legs) combustible surface Actual Shipping

65

4

EQUIPMENT SPECIFICATIONS

SPECIFICATIONS

Current Model

224S-NAT X

224SHE-NAT X 5 WC
224SR-LP X 10 WC 240V/60Hz 0.25 1.0
224SR-NAT X 5 WC
236SC-NAT X 5 WC
236SCHG-NAT X 5 WC
236SHE-NAT X 5 WC
236SHG-NAT X 5 WC
236S-LP X 10 WC
236S-NAT X 5 WC
248SHG-NAT X 5 WC
248SHG-LP X 10 WC
248SHE-NAT X 5 WC
248S-LP X 10 WC
248S-NAT X 5 WC
248S-NATSC X 5 WC
248SR-LP X 10 WC 240V/60Hz 0.25 1.0
248SR-NAT X 5 WC
260S-LP X 10 WC
260S-NAT X 5 WC
260SC-NAT X 5 WC
260S-NATSC X 5 WC
260SCHE-NAT X 5 WC
272S-LP X 10 WC
272S-NAT X 5 WC
272S-NATSC X 5 WC
272SB-NAT X 5 WC
272SHE-NAT X 5 WC
272SHG-NAT X 5 WC

NAT.Gas LP. Gas Burner Input Manifold Press. Gas Connection (3/4” NPT) Voltage Total kW Phase Amps /Line

Gas Requirements Electrical Requirments

5 WC

115V/60Hz 0.5

50,000 BTU/hr

81,000 BTU/hr

115V/60Hz 0.5 2.0

1

27,000

108,000 BTU/hr

135,000 BTU/hr

115V/60Hz 0.5 2.0

2 162,000 BTU/hr

2.0224SC-NAT X 5 WC

1

5

EQUIPMENT DESCRIPTION

1” Griddle Surface

Panel Cover Removed for Clarity

Gutter

Legs

Section

Temp. Dial

Section

Power Switch

Grease

Pan

Power

Indicator

Main
Power
Switch

IL1575

Gas

Regulator

Exterior Construction

The griddle dimensions are 17” (43.18cm) High, 30” (76.20cm) Deep, and width is dependent on the
actual model number.

The Sides, Bottom, and Rear wall are constructed of double wall stainless steel, which allows closer
installation to combustible surfaces.

The stainless steel drop-down door keeps the controls cool and control area clean.

The griddle surface is made of 1” thick, highly polished steel to reduce hot and cold spots, recovery
problems, warping, and ensure even heat to the edges of the griddle.

Controls

The Selectronic Griddle comes with the solid state controls which include:

• A Main Power Switch & Power Indicator for the entire unit.

• Each twelve-inch section has its own temperature selector switch that snaps into place to lock in

• Each twelve-inch section of the griddle is controlled by an area sensitive RTD probe, which can

Technical

• Griddle operates on either Natural gas or Propane. This must be specied when ordering. It is

• Floor space required is 30” (76.20cm) Deep, and width is 2 ft, 3ft, 4ft, 5ft, or 6ft depending on actual

• The griddle weighs 260, 390, 520, 650, 780 lbs. depending on actual model number.

GriddleGasandVoltageSpecications

The Lang Model can be connected to any 120 Volt source. The gas and electrical specications are
listed in the table on the previous page.

NOTICE The data plate is on the right side of the griddle. The oven voltage,

any temperature from 175°F to 450°F (79°C to 232°C) in 25° increments.

sense and react to a temperature change of +/- 4°F.

shipped with a Power Cord and Plug attached.

model number.

wattage,serialnumber,wiresize,andclearancespecicationsare

on the data plate. This information should be carefully read and
understood before proceeding with the installation.

6

CAUTION

UNPACKING

Receiving the Griddle

Upon receipt, check for freight damage, both visible and concealed.
Visible damage should be noted on the freight bill at the time of delivery and
signed by the carrier’s agent. Concealed loss or damage means it does not
become apparent until the merchandise has been unpacked. If concealed
loss or damage is discovered upon unpacking, make a written request for
inspection by the carrier’s agent within 15 days of delivery. All packing
material should be kept for inspection. Do not return damaged

merchandise to Star Manufacturing Company. File your claim with the
carrier.

Location

Prior to un-crating, move the oven as near to its intended location as practical. The crating will help
protect the unit from the physical damage normally associated with moving it through hallways and
doorways.

Un-crating

The griddle will arrive completely assembled inside a wood frame and strapped to a skid.
Cut the straps and remove the wood frame.

The oven can now be removed from the skid.

THE UNIT IS EXTREMELY HEAVY. FOR SAFE HANDLING, INSTALLER
SHOULD OBTAIN HELP AS NEEDED, OR EMPLOY APPROPRIATE MATERIALS
HANDLING EQUIPMENT (SUCH AS A FORKLIFT, DOLLY, OR PALLET JACK)
TO REMOVE THE UNIT FROM THE SKID AND MOVE IT TO THE PLACE OF
INSTALLATION.

ANY STAND, COUNTER OR OTHER DEVICE ON WHICH OVEN WILL BE
LOCATED MUST BE DESIGNED TO SUPPORT THE WEIGHT OF THE GRIDDLE.

SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK WHEN CUT.

VENTILATION & CLEARENCE

CLEARANCE

For use on non-combustible countertops only.
Combustible and non-combustible material must be at least 48” (120cm) from the top of the
appliance and 5” (150mm) from the sides and back. Adequate clearance should also be provided
for proper operation and servicing.

AIR SUPPLY

Make certain not to obstruct the  ow of combustion and ventilation air. Provisions for adequate air
supply must be furnished. The legs supplied with the unit must be installed. Make certain that air
intake openings in the bottom of the appliance are not obstructed. They are essential for proper
combustion and operation of the appliance.

EXHAUST CANOPY

It is essential that facilities be provided over the griddle to carry off fumes and gases. However,
the unit should not be directly connected to a  ue or stack.

7

INSTALLATION

Electrical Connection

The 120V griddles are supplied with a cord and plug, 240V units are not. The 120V receptacle is not
provided with the griddle.

Follow the receptacle manufacturer’s instructions when connecting the receptacle to the power supply.

Gas Connection

This griddle is manufactured for use with the type of gas indicted on the nameplate.
Contact the factory if your type of gas does not match the nameplate data.

All gas connectors must be in accordance with local codes and comply with the National Fuel Federal
Gas Codes ANSI Z223.1 latest edition.

This appliance should be installed with a separate gas valve in the gas line ahead of the unit. Use a
3/4 inch or larger gas supply line.

Remove the 5/16 inch nuts securing the rear of burners. These nuts are for securing the main burners
during transportation only. The rear burner shield must be removed to gain access to the nuts.

A pressure regulator for the type of gas specied is supplied with each appliance.

This regulator must be installed in the gas supply line. (Note the direction of the gas ow arrow.)
The pressure in the manifold of the appliance should be tested with a manometer and the regulator
adjusted for proper pressure with the appliance operating at full re. A 1/8 inch NPT tap is provided in
the manifold for connecting a manometer.

Correct manifold pressures are:
5 inches water column for natural gas
10 inches water column for propane

When replacing the plug in the manifold, a pipe joint compound or sealant should be used that is
resistant to the action of liquid petroleum gas.

Initial adjustments are the responsibility of the installer and are not chargeable to Star Manufacturing
International.

After the griddle is in its nal position, adjust the legs to create 1/8 inch slant from back to front.
This will allow the grease to run into the grease gutter and provide the proper combustion air for the
burners.

DANGER: THIS APPLIANCE MUST BE GROUNDED AT THE TERMINAL

PROVIDED. FAILURE TO GROUND THE APPLIANCE COULD
RESULT IN ELECTROCUTION AND DEATH.

INSTALLATION OF THE UNIT MUST BE DONE BY PERSONNEL

QUALIFIED TO WORK WITH ELECTRICITY AND PLUMBING.

WARNING

IMPROPER INSTALLATION CAN CAUSE INJURY TO PERSONNEL
AND/OR DAMAGE TO EQUIPMENT. UNIT MUST BE INSTALLED IN
ACCORDANCE WITH ALL APPLICABLE CODES.

NOTICE: The data plate is located inside the control compartment of each

griddle.Thegriddlevoltage,serialnumber,gasspecications,and
clearancespecicationsareonthedataplate.Thisinformation

should be carefully read and understood before proceeding with
the installation.

NOTICE: The installation of any components such as a vent hood, grease

extractors,reextinguishersystems,mustconformtotheir

applicable National, State and locally recognized installation
standards.

8

INITIAL START UP

Initial Lighting Procedure

Clean the preservative coating from the griddle plate and splash guard. Add a mild detergent to hot
water and wash the griddle plate and splash guard. Rinse with a damp sponge and dry with a clean
rag.

WARNING: BEFORE LIGHTING, USE A SOAP AND WATER SOLUTION TO

TEST ALL JOINTS FOR GAS LEAKS.

• Plug the unit into a power supply that matches what is listed on the nameplate.

• Turn the ON-STANDBY toggle switch to ON.

• Set the temperature dials to the desired temperature.

• Turn the toggle switch to each section to ON.

• To turn the griddle off, simply turn the main toggle switch to STANDBY.

Seasoning the Griddle Plate (non chrome only)

• Set the temperature dials to 300°F (148°C).

• Observe the burners through the opening at the top of the control panel.

• When the burners go OFF, apply a thin coat of high-grade, non-salted vegetable oil to the
griddle surface.

• Rub the oil into the griddle surface with the at side of a spatula or a towel.

• Recoat any dry spots that appear then wait two minutes and wipe off any excess oil.

• Repeat the seasoning process at 350°F (176°C) and at 400°F (204°C).

NOTICE: Duringtherstfewhoursofoperationyoumaynoticeasmall

amount of smoke coming off the griddle, and a faint odor from
the smoke. This is normal for a new griddle and will disappear

aftertherstfewhoursofuse.

9

OPERATION

Setting the Griddle Temperature

The suggested time and temperature chart (below) is provided as a guide for the products listed only.

If different temperature settings are to be used, select one side of the griddle and operate at the lowest
temperature. Adjoining sections should be set at progressively higher temperatures.
Do not try to operate the end sections hot and the center sections cool.

ALWAYS KEEP THE AREA NEAR THE APPLIANCE FREE FROM

COMBUSTIBLE MATERIALS.

KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN AND DRY. IF

CAUTION

SPILLS OCCUR, CLEAN IMMEDIATELY, TO AVOID THE DANGER
OF SLIPS OR FALLS.

SUGGESTED TIMES AND TEMPERATURES

TEMPERATURE

PRODUCTS

HAMBURGER

2 patties per LB 6 to 8

4 patties per LB 4 to 6

6 patties per LB 3 to 4

(F / C) TIME (MIN)

350°F (176°C)

STEAKS

1/2 to 3/4 inch thick, cooked

medium

3/4 to 1 inch thick, cooked

medium 8 to 10

Lamb Chops

Pork Chops 6 to 8

Salmon 6 to 8

Halibut

Snapper 6 to 8

Hashbrown Potatoes 375°F (190°C) 3 to 4

Bacon

Sausage Links or Patties 3 to 4

Ham (Pre-cooked) 375°F (190°C) 2

Eggs 275°F (135°C) 2 to 4

375°F (190°C)

350°F (176°C)

325°F (162°C)

350°F (176°C)

5 to 7

6 to 8

6 to 8

3 to 4

Note: The times and temperatures in this chart are intended as a general

guide and starting point. Your actual times and temperatures may vary from

this chart.

10

OPERATION

Loading the Griddle

An understanding of how the griddle sections are controlled will be a valuable aid in loading your
griddle.

Each 12 inch section of your griddle is independently controlled. The temperature control sensor is
mounted under the griddle plate in the center of each cooking section.

If the product is loaded directly over the temperature sensor, that section will turn on and the
burner will heat the entire cooking section. If the product is loaded to the side, front or back of the
temperature sensor, the thermostat will react to the temperature change much slowly.

During slow periods with minimal loads, do not load directly over the thermostat sensors as this will
unnecessarily turn the burners on and overheat the remainder of the section not being utilized.

Turn the product and continue cooking until it has reached its desired degree of doneness.

Remove the product from the griddle.

When reloading the griddle, rst use the griddle surface on which a previous load was not placed.
This will insure you the proper griddle temperature.

11

SEQUENCE OF OPERATION

Power On

When the griddle is connected to 115 Volt power, the spark module for each section starts sparking.
While they are sparking the solenoid valve for the pilot burners are energized.

When the individual pilot burners ignite, and the pilot ame is veried, the spark module will stop
sparking. Note: The pilot burners will remain lit until the griddle is removed from power or the gas is
shut off.

When the main switch is turned on, 24 Volts is applied to the temperature control circuit.

When one of the individual section’s switch is turned on, it provides power to the circuit board for that
section.

The operator can now set the temperature of that section by selecting it on the temperature dial.

When the temperature on the dial is set higher than the temperature of the griddle section the circuit
board will generate a “Heat call”. This call (24 VAC Signal) goes to the solenoid valve opening the
valve. The pilot burner ignites the main burner.

As the griddle section temperature increases the temperature sense probe resistance increases.

When the griddle section reaches the temperature set on the selector switch, the circuit board which
monitors the probe resistance will turn off the heat call and there by close the gas valve.

When the griddle temperature drops below the set temperature the circuit board generates a new
heat call and the sequence repeats.

MAINTENANCE & CLEANING

Griddle Care (Chromium Surfaces)

It takes very little time and effort to keep this Industrial Chromium griddle surface sparkling clean and
performing at top efciency. DO NOT allow grease to accumulate as it will carbonize and become
difcult to remove. To prevent this condition the following cleaning suggestions should be followed:

1. Remove excess grease and food regularly with a 4” (100mm) wide Razor Sharp type scraper
and wipe surface with a damp cloth if desired.

2. Following the scraping, for end of the day cleaning, a damp cloth and a non-silicated,
nonabrasive, non-chlorinated cleaner such as Bon-Ami may be used to wipe surface clean,
followed by wiping with a clean wet cloth.

3. Follow steps 2 and 3 from Griddle Care (Non-Chromium Surfaces) above.

CAUTION

1. Never use pumice, griddle stones, or abrasives on a chromium surface.

2. Never strike a chromium griddle surface with a sharp instrument or spatula edge.

3. Never use steel wool.

4. Never use commercial liquid grill cleaner on the griddle surface.

5. Abusing surface voids the warranty.

CHROME GRIDDLE SURFACE LIMITED WARRANTY EXCLUSIONS

Your Chrome griddle has been designed to give you many years of cooking reliability and requires
minimum maintenance to keep the chrome surface in its original condition. All Chrome griddle
surfaces are warranted for a period of 5 years against manufacturing defects to the original owner
from the date of installation. This limited warranty is void if it is determined by Lang Manufacturing
or one of its authorized representatives that the chrome surface has been misused or abused or
subjected to the following situations:

1. Improperly installed.

2. Incorrect voltage applied to Chrome units allowing the surface to overheat and discolor.

3. The misuse of any instrument or tool which scratches or makes indentations in the surface which
could cause the surface to peel, ake, or chip off.

4. The use of any chemical or abrasive cleaning solution, griddle brick, stone, screen or other
cleaning products which could damage and affect the performance of the chrome surface.

5. The neglect of daily routine maintenance to the chromium surface.

12

MAINTENANCE & CLEANING continued

IL1578

Daily Cleaning (Non chrome only)

• Empty the grease drawer daily or whenever it is 3/4 full. It is easily removed for washing.

• Keep the griddle surface clean. After each cooking load, scrape the griddle surface to remove any
carbonized grease.

• Once a day or when necessary the non chrome griddle surface should be thoroughly cleaned and
seasoned again. Use a griddle stone, griddle pad, or liquid cleaner. Rub with the grain of the
metal, being careful not to scrape the splash guard.

• Chrome griddle surfaces can be scraped with a 4” wide Razor Sharp scrapper and wipe surface
with a damp cloth.

• Following the scraping, a damp cloth and non-silicated, non-abrasive, non-chlorinated cleaner such
as Bon-Ami may be used to wipe surface clean, followed by wiping with a clean wet cloth.

Weekly Cleaning (Non chrome only)

• A mild detergent with water or one of the many commercial cleaners may be used.

• Be sure to rinse thoroughly and coat the griddle with a thin lm of oil to prevent rusting,
non-chrome surfaces only.

• Clean the exterior of the appliance with hot water and a mild detergent to maintain a gleaming
appearance.

• Re-season the griddle plate after each cleaning, non-chrome surfaces only.

Burner Air Shutter Adjustment

• The air shutters are pre-set at the factory.
However, minor adjustments may be required in
the eld to accommodate differences in gas and
elevation.

• To adjust the air shutters, loosen the set screw
holding the air damper to the burner near the gas
inlet.

• Adjust the air mixture until the burner ame just
ickers on the burner. “Lift-off” or yellow ame
indicates improper shutter adjustment.

• Periodically inspect and clean the air shutters to
insure complete combustion.

Set Screw

Air Shutter

Burner

WARNING: KEEP WATER AND SOLUTIONS OUT OF CONTROLS. NEVER SPRAY

WARNING

OR HOSE CONTROL CONSOLE, ELECTRICAL CONNECTIONS, ETC.

CAUTION: MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES, MUCOUS

MEMBRANES AND CLOTHING. PRECAUTIONS SHOULD BE TAKEN
TO WEAR RUBBER GLOVES, GOGGLES OR FACE SHIELD AND

CAUTION

PROTECTIVE CLOTHING. CAREFULLY READ THE WARNING AND
FOLLOW THE DIRECTIONS ON THE LABEL OF THE CLEANER TO
BE USED.

NOTICE: Never leave a chlorine sanitizer in contact with stainless steel

surfaces longer than 10 minutes. Longer contact can cause
corrosion.

13

TROUBLESHOOTING

Symptoms

The chart below is to assist in the troubleshooting of the griddle.

Refer to the Symptoms column to locate the type of failure then to the Possible Cause for the items to be
checked.

To test for a possible cause, refer to the TEST section (on the following page) and locate the Possible Cause
then refer to test to identify test procedures.

SYMPTON POSSIBLE CAUSE

Entire griddle not lighting

Power indicator is not lit

Section will not heat

Product burning

Product under done

Doesn’t ignite

• Failed regulator or plugged regulator vent

• Failed transformer

• No power to cord outlet

• Griddle unplugged from outlet

• Failed power cord or plug

• Failed power switch

• Failed pilot light

• Failed gas valve

• Failed spark module

• Failed circuit board

• Failed temperature sensor

• Plugged pilot orice

• Product is cooked too long

• Failed temperature sensor

• Failed circuit board

• Failed temperature selector

• Open wire between selector and circuit board

• Failed temperature sensor

• Failed circuit board

• Failed temperature selector

• Incorrect Gas pressure

• Failed igniter

• Improper gas pressure

• No power

• Failed spark module

14

TROUBLESSHOOTING CONT.

TESTS

POSSIBLE CAUSE TEST

Failed Regulator • Replace regulator

Failed transformer • Check transformer for correct voltage, replace as necessary

Failed power cord or plug • Check cord and plug for proper voltage

Failed power switch • Check switch for continuity across poles

Failed pilot light • Check for continuity across pilot light leads

Failed gas valve

Failed igniter • Replace as necessary

Failed spark module • Check for correct incoming voltage at module

Failed circuit board • Check for proper voltage and operation

Failed temperature sensor • Ohm sensor for correct resistance

Failed temperature selector • Remove the wires and check the resistance on all settings

Open wire between selector and
circuit board

Incorrect gas pressure • Adjust to correct pressure

Plugged regulator vent, or orice • Clean as necessary

• Remove the wires from the valve terminals and check for
continuity across the coil

• Replace as necessary

NOTICE: Service on this, or any other, LANG appliance must be performed by

qualiedpersonnelonly.ConsultyourLANGauthorizedserviceagent

directory or call the factory at [phone],
or WWW.LANGWORLD.COM For the service agent nearest you.

BOTH HIGH AND LOW VOLTAGES ARE PRESENT INSIDE THIS

APPLIANCE WHEN THE UNIT IS PLUGGED/WIRED INTO A LIVE
RECEPTACLE. BEFORE REPLACING ANY PARTS, DISCONNECT THE

WARNING

UNIT FROM THE ELECTRIC POWER SUPPLY.

USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED

BY LANG OR THEIR AUTHORIZED DISTRIBUTORS CAN CAUSE BODILY
INJURY TO THE OPERATOR AND DAMAGE TO THE EQUIPMENT AND

CAUTION

WILL VOID ALL WARRANTIES.

15

PART NO.

JRA

GRN

WHT

BLK

POWER CORD

BLK

2M-61122-W11

WHT

BLK

WHT

DESCRIPTION OF CHANGE DR

ADDED RELAY TERMINAL DESIGNATIONS

AND RELAY WIRING NOTE

120V

24V

TRANSFORMER

TERMINAL STRIP

L1N

WHT

BLK

BLK

BLK

INDICATOR

LAMP

POWER SWITCH

BLK

Wire Diagram - Selectronic Gas Griddles

MODEL NO.

MATERIAL

# 10 SUNNEN DRIVE

STAR MANUFACTURING INTERNATIONAL INC.

REV. DATE/ECO

TITLE

REVISIONS

3/4/13

DATE:

CK:

ADAMS

TOLERANCE: UNLESS NOTED FRACTIONS ±3/64

FINISH

DR:

ST. LOUIS, MO. 63143, USA

7/3/2013

ECO 12993

A

± .030, .xx ± .015, .xxx ± .005

, .x

DECIMALS

YEL

BLU

PILOT

VALVE

BLK

WHT

& FIRST SECTION
POWER CONNECTION

BLK

WHT

6

4

1

2

5

3

GRN

PILOT

MODULE

ORG

PILOT

BURNER

BLK

WHT

SECOND SECTION

GRN

PILOT

MODULE

6

4

1

2

5

3

ORG

PILOT

BURNER

BLK

WHT

WHT

WHT

BLK

BLK

YEL

YEL

RED

RED

RED

YEL

YEL

BRN

BRN

YEL

RED

RED

YEL

CONNECT TO

HOOD

SWITCHSWITCH

RTD

YEL

RELAY

ORG

BLU

NO

COM

RED

TEMPERATURE

CONTROL

BOARD

1

2

RED

BLK

5

6

7

8

9

GRN

1
2
3
4
5

12 POSITION

SWITCH

SEE NOTE 1

BURNER

VALVE

TEMPERATURE

CONTROL

RED

RTD

YEL

RELAY

ORG

BLU

NO

COM

BRN BRN

BURNER

VALVE

BOARD

1

2

RED

BLK

5

6

7

8

9

GRN

1
2
3
4
5

12 POSITION

SWITCH

THE BROWN WIRES ATTACHED TO THE RELAYS ARE

ARE CONNECTED TO THE "NO" AND "COM" TERMINALS.

NOTES:

1.

INC. NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED

THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L

16

LIKE SECOND SECTION

ADDITIONAL SECTIONS

JRA

JRA

PART NO.

2M-61122-W38

DESCRIPTION OF CHANGE DR

ADDED RELAY TERMINAL DESIGNATIONS

AND RELAY WIRING NOTE

7/3/2013

ECO 12993

B

REV. DATE/ECO

W/D SELECTRONIC 36" GAS GRIDDLE WITH CSG24 CLAMSHELL

MODEL NO.

TITLE

POWER CORD

CHANGED CONNECTION OF HOOD WIRES 3 & 4

FROM TRANSFORMER TO POWER SWITCH

7/22/2013

ECO 13035

C

TRANSFORMER

REVISIONS

GRN

WHT

BLK

BLK

WHT

120V

24V

YEL

BLU

MATERIAL

12/19/2007

DATE:

°
1
±

CK.

DJS
:

ANGLES

DR

TOLERANCE: UNLESS NOTED: .xxx ± .015

FINISH

PILOT

VALVE

WHT

1

2

GRN

PILOT

MODULE

WHT

BLK

WHT

BLK

BLK

WHT

BLK

6

4

5

3

ORG

PILOT

BURNER

VALVE
AUTO CUTOFF

29 YEL

30 GRN

HVT

GRN

WHT

BLK

POWER CORD

1 2 3

SPARK MODULE

TH

VALVE

SENSOR

GROUND

GROUND

20 YEL

23 RED

26 GRN

28 TAN

27 ORG

24 GRN

WHT

BLK

INDICATOR

BLK

TERMINAL STRIP

WHT

L1N

BLK

LAMP

POWER SWITCH

TAN 4

TAN 4

BLK

BLK

5 BLK

9 WHT

8 BLK

31 WHT

6 WHT

AIR SWITCH

NO C

10 BLK

120V

7 GRN

34 GRN

21 TAN

TILT SWITCH

22 TAN

32 RED

BURNER

TRANSFORMER

YEL

RED

RED

YEL

24V

VALVE

TAN 3

12 YEL

12 YEL

BRN

SWITCHSWITCH

RTD

YEL

RELAY

NO

COM

YEL

RED

BLU

ORG

RED

TEMPERATURE

CONTROL

BOARD

1

2

5

6

7

8

9

RED

BLK

GRN

CAP THESE

CONNECTORS

1
2
3
4
5

12 POSITION

SWITCH

16 BLU

18 BLK

15 BRN

17 BRN

19 BLU

CAPACITOR

BLOWER

35 GRN

NOT USED

STOW WHEN

25 GRN

SENSOR

IGNITOR

33 GRN

YEL

BURNER

VALVE

RED

# 10 SUNNEN DRIVE

ST. LOUIS, MO. 63143, USA

STAR MANUFACTURING INTERNATIONAL INC.

INC. NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED

THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L

THE BROWN WIRES ATTACHED TO THE RELAYS ARE

ARE CONNECTED TO THE "NO" AND "COM" TERMINALS.

NOTES:

1.

PILOT

PILOT

PILOT

PILOT

GRN

MODULE

BURNER

GRN

MODULE

BURNER

FOR USE WITH

RELAY

INSULATED SPADE

CONNECTORS

TEMPERATURE

CONTROL

BOARD

YEL

BLK

WHT

RED

RTD

BLK

WHT

6

4

1

2

5

3

BRN

RELAY

COM

YEL

BRN BRN

ORG

RED

YEL

BLK

WHT

RED

RTD

BLK

WHT

6

4

1

2

5

3

BRN

RELAY

COM

YEL

BRN

ORG

GRIDDLE

RED

1

2

YEL

ORG

BLU

NO

BURNER

VALVE

RED

BLK

5

6

7

8

9

GRN

12 POSITION

SWITCH

1
2
3
4
5

CARRIAGE BOX

TEMPERATURE

CONTROL

RED

BOARD

1

2

RED

BLK

5

6

7

8

9

GRN

12 POSITION

SWITCH

1
2
3
4
5

SEE NOTE 3

SWITCH

YEL

ORG

BLU

NO

BURNER

VALVE

OPTIONAL TIMER

CLAMSHELL HOOD

17

BLK

BLK

PART NO.

MODEL NO.

2M-61122-W11-1

DESCRIPTION OF CHANGE DR

TRANSFORMER

120V

240V

TRANSFORMER

Wire Diagram - Selectronic Gas Griddles

REV. DATE/ECO

TITLE

PILOT

VALVE

REVISIONS

9/23/14

DATE:

CK:

± .030, .xx ± .015, .xxx ± .005

, .x

ADAMS

240V

SUPPLY

& FIRST SECTION
POWER CONNECTION

GRN

PILOT

MODULE

PILOT

BURNER

120V

24V

WHT

1

2

BLU

BLK

WHT

3

4

BLK

5

ORG

WHT

YEL

6

BLK

WHT

WHT

BLK

YEL

WHT

RED

RED

BLK

BRN

YEL

TERMINAL STRIP

L1N

RTD

COM

YEL

RELAY

NO

RED

SWITCHSWITCH

YEL

YEL

BURNER

VALVE

WHT

RED

ORG

BLU

BLK

RED

BLK

1

2

5

6

7

8

9

LAMP

INDICATOR

POWER SWITCH

TEMPERATURE

CONTROL

BOARD

RED

BLK

BLK

CONNECT TO

GRN

HOOD

12 POSITION

SWITCH

1
2
3
4
5

SEE NOTE 1

MATERIAL

TOLERANCE: UNLESS NOTED FRACTIONS ±3/64

FINISH

DR:

# 10 SUNNEN DRIVE

ST. LOUIS, MO. 63143, USA

STAR MANUFACTURING INTERNATIONAL INC.

INC. NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED

THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L

DECIMALS

NOTES:

THE BROWN WIRES ATTACHED TO THE RELAYS ARE

ARE CONNECTED TO THE "NO" AND "COM" TERMINALS.

1.

BLK

WHT

SECOND SECTION

GRN

PILOT

MODULE

4

1

2

3

ORG

PILOT

BURNER

TEMPERATURE

CONTROL

WHT

BLK

YEL

RED

RTD

RED

YEL

BRN

6

5

RELAY

ORG

BLU

NO

COM

YEL

BRN BRN

BURNER

VALVE

LIKE SECOND SECTION

ADDITIONAL SECTIONS

BOARD

1

2

RED

BLK

5

6

7

8

9

GRN

1
2
3
4
5

12 POSITION

SWITCH

2M-W360: GAS SELECTRONIC GRIDDLE

2M-W360: GAS SELECTRONIC GRIDDLE

Units mfg before July 2013 :SEE DETAIL A

Units mfg after July 2013 :SEE DETAIL B

25

1

2

3

4

Electrical Conduit

21

22

23

24

20

19

18

17

16

5

6

7

11

10

9

8

12

13

14

15

2M-W360: GAS SELECTRONIC GRIDDLE

Model: 224S thru 272S GAS SELECTRONIC GRIDDLE

SK2404 Rev. A 7/18/13

PARTS LIST March 3, 2015, Rev. J

Model No: 224S-NAT

Selectronic Electric Griddle

Key

Number

1 K9-EZG-462-1 1 PLATE ASY 2’ SEL .5 GRV 224S
K9-EZG-462-02 1 PLATE ASY 2’SEL W/XLH-12 224SHE
K9-EZG-462-60 1 PLATE ASY-2’ SEL GRV CHROME 224SC
K9-EZG-462-W61 1 PLT ASSY 2’ SEL CHR 224SCHG
K9-EZGR-487-21 1 PLATE ASSY 2’ SEL EZGR RR 224SR
2 K9-41100-24 2 PROBE - ELECTRONIC #1517 224S, 224SR
3 K9-EZG-232-01 2 WELD BURNER #42 224S
4 2V-80501-04 1 GAS REG 3/4X3/4 CLS I 224S
6 K9-EZG-397 1 CENTER BURNER BAFFLE D 224S
7 K9-EZG-400 1 END BURNER BAFFLE 224S
8 2A-Z0314 4 FOOT, 4” DIE CAST 224S
9 2E-30304-22 2 SWTCB175-450oFW/41100-13 224S
10 2K-70801-07 6 SPACER SUPPORT 1/2LG 224S
11 2E-40101-19 2 CIRBD SI TEMP CNTRL NO 224S
12 2E-30303-18 2 SWTTOGON-OFFSPST1/4HP125V 224S
13 2E-30303-06 1 SWT TOG ON-ON DPDT BLK 224S
14 2J-31601-07 1 PILOT LT 28V 6 LEAD WHT 224S
15 K9-EZG-W597 1 CONTROL PANEL ASSY 224S
K9-EZGR-W597 1 CONTROL PANEL 2’ SEL REAR 224SR
16 2M-60301-131 1 LABEL - ON / STAND BY 224S
17 2E-30303-05 2 SWT PLATE ON/OFF 224S
18 2M-60301-29 2 PNLLBL SELCT SWTDIAL 450o 224S
19 2R-70701-28 2 KNB BLK 1/4BUSH2SETSCW@90 224S
20 K9-60102-144 1 CONTROL PANEL COVER 2’ 224S
21 2M-60301-43 1 DIE CAST PLT LANG SATIN 224S
K9-60301-43-1 1 DIE CAST LOG + TINNERMAN 224S
23 2C-20103-02 AR SCRW SM PLT 10 X .5 PHLSL 224S
24 K9-EZG-349 1 GREASE DRAWER SLIDE 2’ 224S
K9-EZGR-352 1 SPOTWELD BUCKET SLIDE 224SR
25 K9-EZG-343 1 GREASE DRAWER ASSY 2’ 224S
K9-EZGR-338 1 SPOT GREASE DRAWER 224SR
NI 2C-9788 3 MAGNETIC CATCH W/STRIKE 224S
NI 2E-31107-02 1 CORD SET 14/3 X 8’ 15A 224S
NI 2E-EZG-712 2 HARNESS, SELECTRONIC 224S
NI 2K-70308-01 1 PIPE PLUG REG 1/8 NPT BLK 224S
NI 2M-60301-27 1 PNL LBL SLECTRONIC 4’ G4E 224S

Part

Number

Qty
Per

Description

NI 2P-50100-15 1 GRIDDLE SCRAPER 12” CROME UNITS
NI 2P-50100-15-1 - RE-FILL REPLACEMENTS CROME UNITS
NI 2P-50100-16 1 BOM AMI CLEANER CROME UNITS
NI 2P-50100-17 1 20” PALMYRA BRUSH CROME UNITS

2M-W360: GAS SELECTRONIC GRIDDLE

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1
INCLUDE MODEL AND SERIAL NUMBER OF 1

Some items are included for illustrative purposes only and in certain instances may not be available.

PARTS LIST March 3, 2015, Rev. J

Model No: 236S-LP, 236S-NAT, 236SC-NAT 236SCHG-NAT, 236SHE-NAT, 236SHG-NAT

Selectronic Gas Griddle

Key

Number

1 K9-EZG-464-1 1 PLATE ASY 3’ SEL .5 GRV 236S
K9-EZG-464-01 1 PLATE ASY 3’ SEL .5 GRV 236SHG
K9-EZG-464-61 1 PLATE ASY 3’ SEL .5 GRV 236SCHG
K9-EZG-464-02 1 PLATE ASY 3’ SEL W/XLH-12 236SHE
K9-EZGR-487-301 1 PLATE ASY 3’ SEL REAR GUTTER CHROME 236SRC
K9-EZGR-487-32 1 PLATE ASY 3’ SEL REAR GUTTER 236SR
2 K9-41100-24 3 PROBE - ELECTRONIC #1517 ALL
3 K9-EZG-232-01 3 WELD BURNER #42 ALL
4 2V-80501-04 1 GAS REG 3/4X3/4 CLS I 236S-NAT
2V-80501-05 1 GAS REG 3/4X3/4 CLS II 236S-LP
6 K9-EZG-391 1 CENTER BURNER BAFFLE B ALL
7 K9-EZG-400 2 END BURNER BAFFLE ALL
8 2A-Z0314 4 FOOT, 4” DIE CAST ALL
9 2E-30304-22 3 SWTCB175-450oFW/41100-13 ALL
10 2K-70801-07 9 SPACER SUPPORT 1/2LG ALL
11 2E-40101-W19 3 CIRBD SI TEMP CNTRL NO ALL
12 2E-30303-18 3 SWTTOGON-OFFSPST1/4HP125V ALL
13 2E-30303-06 1 SWT TOG ON-ON DPDT BLK ALL
14 2J-31601-07 1 PILOT LT 28V 6 LEAD WHT ALL
15 K9-EZG-600 1 SPOT CNTRL PNL 3’ SEL ALL
16 2M-60301-131 1 LABEL - ON / STAND BY ALL
17 2E-30303-05 3 SWT PLATE ON/OFF ALL
18 2M-60301-29 3 PNLLBL SELCT SWTDIAL 450o ALL
19 2R-70701-28 3 KNB BLK 1/4BUSH2SETSCW@90 ALL
20 K9-60102-42 1 CONTROL PANEL COVER 3’ ALL
21 2M-60301-43 1 DIE CAST PLT LANG SATIN ALL
21 K9-60301-43-1 1 DIE CAST LOG + TINNERMAN ALL
23 2C-20103-02 AR SCRW SM PLT 10 X .5 PHLSL ALL
24 K9-EZG-355 1 GREASE DRAWER SLIDE ALL
25 K9-50303-11 1 GREASE DRAWER ASSY ALL
NI 2C-9788 3 MAGNETIC CATCH W/STRIKE ALL
NI 2E-31107-02 1 CORD SET 14/3 X 8’ 15A ALL
NI 2E-EZG-712 3 HARNESS, SELECTRONIC ALL
NI 2K-70308-01 1 PIPE PLUG REG 1/8 NPT BLK ALL
NI 2M-60301-27 1 PNL LBL SLECTRONIC 4’ G4E ALL

Part

Number

Qty
Per

Description

NI 2P-50100-15 1 GRIDDLE SCRAPER 12” CROME UNITS
NI 2P-50100-15-1 - RE-FILL REPLACEMENTS CROME UNITS
NI 2P-50100-16 1 BOM AMI CLEANER CROME UNITS
NI 2P-50100-17 1 20” PALMYRA BRUSH CROME UNITS

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1
INCLUDE MODEL AND SERIAL NUMBER OF 1

Some items are included for illustrative purposes only and in certain instances may not be available.

2M-W360: GAS SELECTRONIC GRIDDLE

PARTS LIST March 3, 2015, Rev. J

Model No: 248S-LP, 248S-NAT, 248S-NATSC, 248SHG-NAT, 248SHE-NAT

Selectronic Gas Griddle

Key

Number

1 K9-EZG-467-01 1 PLATE ASY 4’SEL .5 GRV 248SHG-NAT
K9-EZG-467-02 1 PLATE ASY 4’SEL .5 GRV W/XLH12 248SHE-NAT
K9-EZG-467-1 1 PLATE ASY 4’SEL .5 GRV 248S-NAT/NATSC/LP
K9-EZG-467-61 1 PLATE ASY 4’ SEL CHROME 248SCHG-NAT
K9-EZG-467-W1 1 PLATE ASY 4’ SEL CHROME 248SC
K9-EZGR-487-42 1 PLATE ASY 4’ SEL REAR 248SR
2 K9-41100-24 4 PROBE - ELECTRONIC #1517 248S
3 K9-EZG-232-01 4 WELD BURNER #42 248S
4 2V-80501-04 1 GAS REG 3/4X3/4 CLS I 248S-NAT
2V-80501-05 1 GAS REG 3/4X3/4 CLS II 248S-LP, 248SHG-LP
5 K9-EZG-388 1 CENTER BURNER BAFFLE A 248S
6 K9-EZG-391 1 CENTER BURNER BAFFLE B 248S
7 K9-EZG-400 2 END BURNER BAFFLE 248S
8 2A-Z0314 4 FOOT, 4” DIE CAST 248S
9 2E-30304-22 4 SWTCB175-450oFW/41100-13 248S
10 2K-70801-07 12 SPACER SUPPORT 1/2LG 248S
11 2E-40101-19 4 CIRBD SI TEMP CNTRL NO 248S
12 2E-30303-18 4 SWTTOGON-OFFSPST1/4HP125V 248S
13 2E-30303-06 1 SWT TOG ON-ON DPDT BLK 248S
14 2J-31601-07 1 PILOT LT 28V 6 LEAD WHT 248S
15 K9-EZG-W603 1 SPOT CNTRL PNL 4’ SEL 248S
K9-EZGR-W605 1 SPOT CNTRL PNL 4’ SEL 248SR
16 2M-60301-131 1 LABEL - ON / STAND BY 248S
17 2E-30303-05 4 SWT PLATE ON/OFF 248S
18 2M-60301-29 4 PNLLBL SELCT SWTDIAL 450o 248S
19 2R-70701-28 4 KNB BLK 1/4BUSH2SETSCW@90 248S
20 K9-60102-122 1 PANEL COVER ASSY 4FT EZG 248S-NAT/LP
21 2M-60301-43 1 DIE CAST PLT LANG SATIN 248S
K9-60301-43-1 1 DIE CAST LOG + TINNERMAN 248S
23 2C-20103-02 50 SCRW SM PLT 10 X .5 PHLSL 248S
24 K9-EZG-355 1 GREASE DRAWER SLIDE 248S
25 K9-50303-11 1 GREASE DRAWER ASSY 248S-NAT/LP
K9-EZG-977 1 GREASE DRAWER ASSY 248S-NATSC
K9-EZGR-338 1 SPOT GREASE DRAWER 248SR
NI 2E-31107-02 1 CORD SET 14/3 X 8’ 15A 248S
NI 2K-70308-01 1 PIPE PLUG REG 1/8 NPT BLK 248S
NI 2M-60301-27 1 PNL LBL SLECTRONIC 4’ G4E 248S-NAT/LP
NI 2C-9788 3 MAGNETIC CATCH W/STRIKE 248S
NI 2E-EZG-712 4 HARNESS, SELECTRONIC 248S

Part

Number

Qty
Per

Description

NI 2P-50100-15 1 GRIDDLE SCRAPER 12” CROME UNITS
NI 2P-50100-15-1 - RE-FILL REPLACEMENTS CROME UNITS
NI 2P-50100-16 1 BOM AMI CLEANER CROME UNITS
NI 2P-50100-17 1 20” PALMYRA BRUSH CROME UNITS

2M-W360: GAS SELECTRONIC GRIDDLE

1

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE

1

INCLUDE MODEL AND SERIAL NUMBER OF

Some items are included for illustrative purposes only and in certain instances may not be available.

PARTS LIST March 3, 2015, Rev. J

Model No: 260S-LP, 260S-NAT, 260S-NATSC

Selectronic Gas Griddle

Key

Number

1 K9-EZG-470-1 1 PLATE ASY 5’SEL .5 GRV 260S
K9-EZG-470-61 1 PLATE ASSY 5’ SEL. CHROME 260SCHE-NAT
K9-EZG-470-60 1 PLATE ASSY 5’ SEL. CHROME 260SC
2 K9-41100-24 5 PROBE - ELECTRONIC #1517 260S
3 K9-EZG-232-01 5 WELD BURNER #42 260S
4 2V-80501-04 1 GAS REG 3/4X3/4 CLS I 260S-NAT
4 2V-80501-05 1 GAS REG 3/4X3/4 CLS II 260S-LP
5 K9-EZG-388 1 CENTER BURNER BAFFLE A 260S
6 K9-EZG-391 2 CENTER BURNER BAFFLE B 260S
7 K9-EZG-400 2 END BURNER BAFFLE 260S
8 2A-Z0314 4 FOOT, 4” DIE CAST 260S-NAT, 260S-LP
2R-200716 4 LEG, 2.5 IN METAL 260S-NATSC
9 2E-30304-22 5 SWTCB175-450oFW/41100-13 260S
10 2K-70801-07 15 SPACER SUPPORT 1/2LG 260S
11 2E-40101-19 5 CIRBD SI TEMP CNTRL NO 260S
12 2E-30303-18 5 SWTTOGON-OFFSPST1/4HP125V 260S
13 2E-30303-06 1 SWT TOG ON-ON DPDT BLK 260S
14 2J-31601-07 1 PILOT LT 28V 6 LEAD WHT 260S
15 K9-EZG-606 1 SPOT CNTRL PNL 5’ SEL 260S
16 2M-60301-131 1 LABEL - ON / STAND BY 260S
17 2E-30303-05 5 SWT PLATE ON/OFF 260S
18 2M-60301-29 5 PNLLBL SELCT SWTDIAL 450o 260S
19 2R-70701-28 5 KNB BLK 1/4BUSH2SETSCW@90 260S
20 K9-EZG-620 1 CONTROL PANEL 5’ COVER 260S-NAT, 260S-LP
21 2M-60301-43 1 DIE CAST PLT LANG SATIN 260S
K9-60301-43-1 1 DIE CAST LOG + TINNERMAN 260S
22 2C-20602-04 2 TINNERAMN SPD NUT 1/8” DIA ALL
23 2C-20103-02 AR SCRW SM PLT 10 X .5 PHLSL 260S
24 K9-EZG-355 2 GREASE DRAWER SLIDE 260S
25 K9-50303-11 2 GREASE DRAWER ASSY 260S
NI 2C-9788 3 MAGNETIC CATCH W/STRIKE 260S
NI 2E-31107-02 1 CORD SET 14/3 X 8’ 15A 260S
NI 2E-EZG-712 5 HARNESS, SELECTRONIC 260S
NI 2K-70308-01 1 PIPE PLUG REG 1/8 NPT BLK 260S
NI 2M-60301-27 1 PNL LBL SLECTRONIC 4’ G4E 260S

Part

Number

Qty
Per

Description

NI 2P-50100-15 1 GRIDDLE SCRAPER 12” CROME UNITS
NI 2P-50100-15-1 - RE-FILL REPLACEMENTS CROME UNITS
NI 2P-50100-16 1 BOM AMI CLEANER CROME UNITS
NI 2P-50100-17 1 20” PALMYRA BRUSH CROME UNITS

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1
INCLUDE MODEL AND SERIAL NUMBER OF 1

Some items are included for illustrative purposes only and in certain instances may not be available.

2M-W360: GAS SELECTRONIC GRIDDLE

PARTS LIST March 3, 2015, Rev. J

Model No: 272S-NAT, 272S-LP, 272S-NATSC, 272SHG

Selectronic Gas Griddle

Key

Number

1 K9-EZG-473-1 1 PLATE ASY 6’SEL .5 GRV 272S
K9-EZG-473-01 1 PLATE ASY 6”SEL .5 GRV W/AGC 272SHG
K9-EZG-473-02 1 PLATE ASY 6’SEL W/XLH-12 272SHE
K9-EZG-473-03 1 PLATE ASY 6’ SEL CHROME 272SCHE
K9-EZGR-487-6 1 PLATE ASY 6’ SEL EZGR .5 272SB
2 K9-41100-24 6 PROBE - ELECTRONIC #1517 ALL
3 K9-EZG-232-01 6 WELD BURNER #42 ALL
4 2V-80501-04 1 GAS REG 3/4X3/4 CLS I 272S-NAT
2V-80501-05 1 GAS REG 3/4X3/4 CLS II 272S-LP
5 K9-EZG-394 2 CENTER BURNER BAFFLE C ALL
6 K9-EZG-391 2 CENTER BURNER BAFFLE B ALL
7 K9-EZG-400 2 END BURNER BAFFLE ALL
8 2A-Z0314 6 FOOT, 4” DIE CAST ALL
9 2E-30304-22 6 SWTCB175-450oFW/41100-13 ALL
10 2K-70801-07 18 SPACER SUPPORT 1/2LG ALL
11 2E-40101-19 6 CIRBD SI TEMP CNTRL NO ALL
12 2E-30303-18 6 SWTTOGON-OFFSPST1/4HP125V ALL
13 2E-30303-06 1 SWT TOG ON-ON DPDT BLK ALL
14 2J-31601-07 1 PILOT LT 28V 6 LEAD WHT ALL
15 K9-EZG-609 1 SPOT CNTRL PNL 6’ SEL 272S
K9-EZGR-609-1 1 SPOT CNTRL PNL 6’ SEL 272SB
16 2M-60301-131 1 LABEL - ON / STAND BY ALL
17 2E-30303-05 6 SWT PLATE ON/OFF ALL
18 2M-60301-29 6 PNLLBL SELCT SWTDIAL 450o ALL
19 2R-70701-28 6 KNB BLK 1/4BUSH2SETSCW@90 ALL
20 K9-EZG-615 2 CONTROL PANEL COVER 3’ ALL
21 2M-60301-43 1 DIE CAST PLT LANG SATIN ALL
K9-60301-43-1 1 DIE CAST LOG + TINNERMAN ALL
22 2C-20602-04 2 TINNERAMN SPD NUT 1/8” DIA ALL
23 2C-20103-02 AR SCRW SM PLT 10 X .5 PHLSL ALL
24 K9-EZG-355 2 GREASE DRAWER SLIDE 272S
K9-EZGR-352 2 SPOTWELD BUCKET SLIDE 272SB
25 K9-50303-11 2 GREASE DRAWER ASSY 272S
K9-EZGR-338 2 SPOT GREASE DRAWER 272SB
NI 2C-9788 6 MAGNETIC CATCH W/STRIKE 272S
NI 2E-30501-03 2 TERM STRP 4 POLE W/PUSH 272SB
NI 2E-31107-02 1 CORD SET 14/3 X 8’ 15A ALL
NI 2E-EZG-712 6 HARNESS, SELECTRONIC ALL
NI 2K-70308-01 2 PIPE PLUG REG 1/8 NPT BLK ALL
NI 2M-60301-27 1 PNL LBL SLECTRONIC 4’ G4E ALL

Part

Number

Qty
Per

Description

NI 2P-50100-15 1 GRIDDLE SCRAPER 12” CROME UNITS
NI 2P-50100-15-1 - RE-FILL REPLACEMENTS CROME UNITS
NI 2P-50100-16 1 BOM AMI CLEANER CROME UNITS
NI 2P-50100-17 1 20” PALMYRA BRUSH CROME UNITS

2M-W360: GAS SELECTRONIC GRIDDLE

IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1
INCLUDE MODEL AND SERIAL NUMBER OF 1

Some items are included for illustrative purposes only and in certain instances may not be available.

15

5

20

17

19

18

16

1

2

3

4

5

6

5

7

8

9

15

15

Manifold Assy, units Mfg Before July 2013

Fig No. Part Number Description

1 2C-20103-02 SCRW SM PLT 10 X .5 PHLSL

2J-80201-24 PLT LT BURNR FR GEI12LEAD

2

2J-80201-25 PLT LT BRNR GEI LT 12 3S2

K9-EZG-637 PILOT TUBE #1

K9-EZG-640 PILOT TUBE #2

3

K9-EZG-643 PILOT TUBE #3

K9-EZG-650 PILOT TUBE #5

K9-EZG-655 PILOT TUBE #9

4 2K-70101-07 BRAS TBE TEE 1/4CC

5 2C-20102-04 SCRW PHD ST 8-32X.5 PLTD

6 2E-31400-07 XFORMR120-208-240/24V40VA

7 2J-80300-03 SPRK IGNITR MODULE SM2

9 2E-30501-03 TERM STRP 4 POLE W/PUSH

10 K9-EZG-628 SOLENOID TUBE A

11 2K-70101-11 BRAS TBE UNON 3/8CC-1/2

12 2V-80502-03 SLENOID VLVE 24VAC 1/2

13 2K-70101-12 BRAS TBE ELBW 3/8CC-1/2

14 K9-EZG-671 BURNER FEED TUBE #3

15 2A-W1185 ORIFICE FITTING - 90 DEG

16 K9-EZG-668 BURNER FEED TUBE #2

17 K9-EZG-288 FLAME SWITCH MOUNT

18 2V-80506-01 FLAME SWT 24 GAS GRID &

19 K9-EZG-631 SOLENOID TUBE B

20 K9-EZG-665 BURNER FEED TUBE #1

NI 2A-45408 ORIFICE HOOD .0935 #42

NI 2A-80400-12 ORIFICE HOOS .0595 #53

NI 2A-80401-03 PILTBRNER ORIFICE .0115LP

NI 2E-40101-19 CIRBD SI TEMP CNTRL NO

10

14

10

11

12

13

Model: Selectronic & ACCU-TEMP MANIFOLD ASSY

DETAIL A

(manufactured before July 2013)

SK2405 Rev.A 7/18/2013

2M-W360: GAS SELECTRONIC GRIDDLE

March 3, 2015, Rev. J

1

4

2

5

3

6

1

7

17

8910

12

6

11

14

13

15a

15

16

Manifold Assy, units Mfg After July 2013

Fig No. Part Number Description Application

1 2K-70101-03 BRASTBEELBOW 1/4NPT-3/8CC

2 2K-70101-06 BRASTEE BRNCH 1/4NPTM-3/8

3 2K-70308-01 PIPE PLUG REG 1/8 NPT BLK

4 2J-80201-25 PLT LT BRNR GEI LT 12 3S2

5 2J-80201-24 PLT LT BURNR FR GEI12LEAD

6 2C-20103-02 SCRW SM PLT 10 X .5 PHLSL

7 2A-W1185 ORIFICE FITTING - 90 DEG

8 2K-45300 FITTING 3/8CC X 1/8NPT

9 2V-80502-W07 VALVE SOLENOID-1/8 NPT

10 2K-70101-124 FITTING 1/8NPT X 3/8COMP.

11 2V-6671 VALVE-LINCOLN BRASS#3817

12 2C-20102-08 SCRW PHD ST 8-32X.375

13 K9-EZG-W297 BRKT,SOLENOID VALVE

14 2C-20102-04 SCRW PHD ST 8-32X.5 PLTD

15 PS-60101-W15 KIT, PILOT IGNITION CONTROL mfg between 7/13 & 3/15

15a 2J-80300-W20-1 PILOT IGNITION MODULE mfg after 3/1/2015

16 2E-30501-03 TERM STRP 4 POLE W/PUSH

2M-W360: GAS SELECTRONIC GRIDDLE

17 2K-70101-07 BRAS TBE TEE 1/4CC

18 2C-20102-04 SCRW PHD ST 8-32X.5 PLTD

2E-31400-07 XFORMR120-208-240/24V40VA

19

2E-31400-37 XFORMER 240V TO 120V 240V, 224SR-LP24, 248SR-LP24

NI 2K-70104-03 FLEXIBLE TUBE 3/8OD X 8

NI 2K-80101-05 TUBE FLEX 1/4 DIA X 6 LNG

NI 2K-Z4921 BURNER TUBE FLEX 3/8 OD

NI 2K-Z6081 PILOT TUBE FLEX 10”

NI 2K-Z6943 GAS LINE 1/4”D x 8”L

NI 2K-Z6945 GAS LINE 1/4”D x 16”L BBQ

NI 2A-45408 ORIFICE HOOD #42 GRID NAT NAT

NI 2A-80400-12 ORIFICE HOOD .0595 #53, LP LP

18

19

DETAIL B

(manufactured after July 2013)

SK2671 Rev. D 5/22/2015

March 3, 2015, Rev. J

STAR INTERNATIONAL HOLDINGS INC. COMPANY

Star - Holman - Lang - Wells - Bloomeld - Toastmaster

10 Sunnen Drive, St. Louis, MO 63143 U.S.A.

[phone]

www.star-mfg.com