Laney RB1 User Manual

Page 1
RB1
USER MANUAL
Page 2
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using electric products, basic cautions should always be followed, including the following.
1. Read all safety and operating instructions before using this product
2. The product should be powered by a three pin `grounded (or earthed) plug connected to a power socket with a grounded earth outlet.
3. All safety and operating instructions should be retained for future reference
5. All operating instructions should be followed
6. This product should not be used near water, i.e. a bathtub, sink, swimming pool, wet basement, etc.
7. This product should be located so that its position does not interfere with its proper ventilation. It should not be placed flat against a wall or placed in a built up enclosure that will impede the flow of cooling air.
8. This product should not be placed near a source of heat such as stove, radiator, or another heat producing amplifier.
9. Connect only to a power supply of the type marker on the unit adjacent to the power supply cord.
10. Never break off the ground pin on a power supply cord.
11. Power supply cords should always be handled carefully. Never walk or place equipment on power supply cords. Periodically check cords for cuts or signs of stress, especially at the plug and the point where the chord exits the unit.
12. The power supply cord should be unplugged when the unit is to be unused for long periods of time.
13. If this product is to be mounted in an equipment rack, rear support should be provided.
14. The user should allow easy access to any mains plug, mains coupler and mains switch used in conjunction with this unit thus making it readily operable.
15. Metal parts can be cleaned with a damp cloth. The vinyl covering used on some units can be cleaned with a damp cloth or ammonia based household cleaner if necessary. Disconnect the unit from the power supply before cleaning.
16. Care should be taken so that objects do not fall and liquids are not spilled into the unit through any ventilation holes or openings. On no account place drinks on the unit.
17. A qualified service technician should check the unit if:
!
The power cord has been damaged
!
Anything has fallen or spilled into the unit
!
The unit does not appear to operate correctly
!
18. The user should not attempt to service the equipment. All service work is done by a qualified service technician.
19. Exposure to extremely high noise levels may cause a permanent hearing gloss. Individuals vary considerably in susceptibility to noise induced hearing loss, but nearly everyone
Duration Per Day In Hours Sound Level dBA, slow response
According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Ear plugs or protectors in the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss if exposure exceeds the limits set forth above. To ensure against potentially dangerous exposure to high sound pressure levels it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation.
The unit has been dropped or the enclosure damaged.
will lose some hearing if exposed to sufficiently intense noise for a sufficient time. The U.S. Government's Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposure.
8 90 6 92 4 95 3 97 2 100 1 ½ 102 1 105 ½ 110 ¼ or less 115
SAVE THESE INSTRUCTIONS
Page 2 /8 Page 3 /8
Page 3
Page 4
Laney
OPERATING INSTRUCTIONS
BEFORE SWITCHING ON
After unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug. Before plugging into the power supply ensure you are connecting to a grounded earth outlet.
If you should wish to change the factory fitted plug yourself, ensure that the wiring convention applicable to the country where the amplifier is to be used is strictly conformed to. As an example in the United Kingdom the cable colour code for connections are as follows.
EARTH OR GROUND - GREEN/YELLOW NEUTRAL - BLUE LIVE - BROWN
NOTE
This manual has been written for easy access of information. The front and rear panels are graphically illustrated, with each control and feature numbered. For a description of the function of each control feature, simply check the number with the explanations adjacent to each panel.
Your Laney amplifier has undergone a thorough two stage, pre-delivery inspection, involving actual play testing.
When you first receive your Laney Bass amp, follow these simple procedures:
(i) Ensure that the amplifier is the correct voltage for the country it is to be used in.
(ii) Connect your instrument with a high quality shielded instrument cable. You have probably spent considerable money on your amplifier and guitar - don’t use poor quality cable it won’t do your gear justice.
Please retain your original carton and packaging so in the unlikely event that some time in the future your amplifier should require servicing you will be able to return it to your dealer securely packed.
Care of your Laney amplifier will prolong it's life.....and yours!
Page 4 /8 Page 5 /8
Page 5
Laney
Dear Player,
Thank you very much for purchasing your new Laney product and becoming part of the worldwide Laney family. Each and every Laney unit is designed and built with the utmost attention to care and detail, so I trust yours will give you many years of enjoyment.
Laney products have a heritage which stretches back to 1967 when I first began building valve amplifiers in my parent’s garage. Since then we have moved on from strength to strength developing an extensive range of guitar, bass, public address and keyboard amplification products along with a list of Laney endorsees that includes some of the world’s most famous and respected musicians. At the same time we believe we have not lost sight of the reason Laney was founded in the first place - a dedication to building great sounding amplification for working musicians.
Warm Regards,
Lyndon Laney CEO
OPERATING INSTRUCTIONS
INTRODUCTION
The RB1 is a 15W Bass combo with an 8 inch loudspeaker in a sturdy wooden cabinet. Its features include; a ¼” jack input, a gain control and a switchable compressor, a flexible EQ system with Bass, Middle, Treble, and an overall Volume control. Should you need to play along to a CD/MP3, you can plug the output of your player into the CD/Line in Socket. A headphone socket is also provided for private practice sessions.
An explanation of these features follows on pages 6-8.
Page 6
Laney
1 2 3 4 5 6 7 8 9 10 11
FRONT PANEL CONTROLS
Input socket for connection of bass guitars. The socket will accommodate High or Low output basses, either Active or Passive.
1
Engages and disengages the on-board compressor, this compresses the input-signal giving a punchier sound. In association with the
2
compressor is an LED to indicate when the compressor is active. The amount of compression is controlled by the Gain control The higher the setting the more compression. With most guitars compression will begin at about 5-6 on the control. It is possible to have the compressor engaged but it only be active during certain periods of playing - typically the most dynamic sections.
This control is used to set the level of gain present in the pre-amp. The higher the level of gain, the more the signal will clip
3
producing distortion. The Gain control should be used in conjunction with the Volume control to produce the desired signal characteristics.
Controls the boost and cut of the low-frequency response of the pre-amplifier.
4
Controls the boost and cut of the mid-frequency response of the pre-amplifier.
5
Controls the boost and cut of the high-frequency response of the pre-amplifier.
6
Sets the overall listening level of the amplifier.
7
Stereo jack socket provided for connecting an external sound source such as; CD players, MP3 players, Minidisc etc.
8
Socket for connecting headphones, With headphones connected, the internal loudspeaker is automatically switched off.
9
10
Indicates power is connected and the amp is switched on. (Always switch off and disconnect power cord when not in use)
11
Main power on/off switch
OPERATING INSTRUCTIONS
7
3
Page 6 /8 Page 7 /8
Page 7
Laney
OPERATING INSTRUCTIONS
1
2
REAR PANEL CONTROLS
Power inlet socket. Connect to your power source. Make sure the specified voltage is correct for your country!
1
Serial Number and model of your unit.
2
SAMPLE SYSTEM
BLOCK DIAGRAM
INPUT
EQ SECTION
GAIN
VOLUME
COMPRESSOR
CD In
POWER AMP
SECTION
ACTIVE
Headphones
INTERNAL LOUDSPEAKER
Page 8
SPECIFICATIONS
Supply Voltage Mains Fuse ~220V>@240V = T2A L. ~100>~120V = T5A L (Time delay) Power Consumption 30W Output Power Rating 15W Loudspeaker 8” Custom Designed Driver Features Switchable Compressor with Activity light. Clip distortion limiter. EQ Bass (±8dBu at 40Hz)
Input Impedance 1M Ohm/100pF Size 375*364*260 (H*W*D) Unit Weight 9.5 Kg Packing Weight 11 Kg
This product conforms to : European EMC directive(2004/108/EC), Low Voltage Directive (72/23/EEC) and CE mark Directive (93/68/EEC)
~100V, ~120V, ~220V, ~230V, ~240V 50/60Hz Factory Option
Middle ( Treble (±8dBu at 3.5KHz)
±8dBu at 800Hz)
Laney
POWER TO THE MUSIC
METAL
JAZZ
BLUES
ROCK
AMPICONS ARE HERE TO HELP!
@
In the interest of continued product development, Laney reserves the right to amend product specification without prior notification.
Loading...