Land Pride PD10 Series, PD15 Series, PD25 Series, PD35 Series Specifications
Post Hole Diggers
PTO Drive
Specifications & Capacities
Post Hole Diggers PTO Drive
PD10 and PD15 Series Post Hole Diggers
PD10 PD15
Tractor HP Range 15 to 30 HP 20 to 40 HP
Weight Without Auger 120 lbs. 161 lbs.
Auger Length 30" 48"
Auger Flight Thickness 1/4”
Auger Pipe 2 1/2" ID
Auger Teeth Forged, Individually Replaceable
40 Degree angle installed on flat side
50 Degree angle installed on angled side
Number of Teeth 6" - 2 teeth
9" & 12" - 4 teeth
Pilot Cast steel, 3 drill points
Driveline Cat. II Shearbolt
Maximum Operating PTO Speed 300 RPM
Gearbox 540 RPM 3:1 Ratio 540 RPM 3.18:1 Ratio
Gearbox Oil Capacity & Type 3.4 Pints of SAE80-90W EP oil 4.6 Pints of SAE80-90W EP oil
Output Shaft 2" O.D. Round
3-Point Hitch Cat. Cat. I
Boom Tube 2 7/8” O.D.
Yoke Tube 2 7/8” O.D.
Options and Accessories
Auger Sizes (Options) 6”, 9”, or 12” 6”, 9”, or 12”
Auger Extensions (Accessories) 7" & 14" Extensions Available
Cat. III Torque Limiter Driveline Not Available Not Available
Hydraulic Down Pressure Kit Available Available
Storage Stand Available Available
PD10 = 31 1/2"
PD15 = 32"
Designs, specifications, features and information are subject to change without notice.
63
PD10 = 52 1/2" w/ 12" Auger
PD15 = 66 1/4" w/ 12" Auger
PD10 = 58 5/8"
PD15 = 77 5/8"
PD10 = 70"
PD15 = 89 1/2"
317-048S continued on next page
26776
6/23/11
Specifications & Capacities
Post Hole Diggers PTO Drive
PD25 and PD35 Series Post Hole Diggers
PD25 PD35
Tractor HP Range 25 to 55 HP 30 to 75 HP
Weight Without Auger 186 lbs. 233 lbs.
Auger Length 48"
Auger Flight Thickness 1/4”
Auger Pipe 2 1/2" ID
Auger Tooth Construction Forged, Individually Replaceable
40 Degree angle installed on flat side
50 Degree angle installed on angled side
Number of Teeth
Pilot Cast steel, 3 drill points
Driveline Cat. Cat. III Shear bolt - Standard
Maximum Operating PTO Speed 300 RPM
Gearbox 540 RPM 3.18:1 Ratio 540 RPM 4:1 Ratio
Gearbox Oil Capacity & Type 4.6 Pints of SAE80-90W EP oil 9.1 Pints of SAE80-90W EP oil
Output Shaft 2" O.D. Round
3-Point Hitch Cat. Cat. I & II
Boom Tube 3 1/2” O.D. 3 1/2” O.D.
Yoke Tube 2 7/8” O.D.
Auger Sizes (Options) 6”, 9”, 12”, 14”, 18”, or 24”
Auger Extensions (Accessories) 7" & 14" Extensions Available
Cat. III Torque Limiter Driveline Available Available
Hydraulic Down Pressure Kit Available Available
Storage Stand Available Available
(6” - 2 teeth) (9” & 12” - 4 teeth) (15” - 5 teeth) (18” - 6 teeth) (24” - 8 teeth)‘
Cat. III Radial pin clutch - Optional (Recommended on Auger Sizes 15" and above.)
Options and Accessories
PD25/35 = 33 1/4"
Designs, specifications, features and information are subject to change without notice.
64
PD25 & PD35 = 68 1/2" w/ 12" Auger
PD25 = 78 1/8"
PD35 = 79 3/8"
PD25 = 89 1/8"
PD35 = 90 3/8"
317-048S end
26776
6/23/11
Loading...