Landoll WL User Manual
INDEPENDENT TOOTH CONTROL INSTALLATION INSTRUCTIONS
www.landoll.com
FOR ML AND WL PULVI-MULCHERS WITH ROTATING TEETH
The teeth will operate independent of lift cylinders
•
Each kit will require either a ratchet jack or hydraulic
•
cylinder to set teeth working depth
WARNING:
Read entire instructions before attempting to assemble these
kits. Failure to comply with this warning can result in personal injury or death,
damage to the machine or its components and inferior operation.
ML SERIES TOOTH CONTROL KITS
9J221 ML TOOTH CONTROL KIT FOR C-TINE
9J222 ML TOOTH CONTROL
9K364 HYDRAULIC KIT FOR ML T
7J237 RATCHET JACK
KIT FOR S-TINE
OOTH CONTROL
WL SERIES TOOTH CONTROL KITS
9J236 WL TOOTH CONTROL KIT FOR C-TINE
9J237 WL TOOTH CONTROL
3K638 HYDRAULIC KIT FOR WL T
9J230 RATCHET JACK KIT FOR WL
Illustrations on the following pages outline installation of the kits with figures
showing the correct placement of existing and new tooth brackets.
KIT FOR S-TINE
OOTH CONTROL
TOOTH CONTROL
KitPn
9J223 1
10-31-07
Note:
After bracket installation always double check position of brackets to tooth
orientation before operating.
When
hydraulic cylinders
are used, plumb hydraulic circuit per hydraulic
schematics attaching hoses to the frame with supplied cable ties where necessary.
If items covered in this manual are not understood, contact your local
Dealer
.
BRILLION )$50(48,30(17
BRILLION, WISCONSIN 54110
Brillion
9J223
9J223
9J223
Page 2
Contents
Converting the CENTER SECTION - Removal of Original Linkage
for S-Tine Conversion ................................................................................................. 2
for C-Tine Conversion ................................................................................................. 3
Center Frame Linkage Bracket Comparison by Tine Style ................................................. 5
Addition of New Linkage Parts - Center
for S-Tine Conversion ................................................................................................. 6, 7
for C-Tine Conversion ................................................................................................. 8, 9
Converting the WINGS - Removal of Original Linkage
for S-Tine Conversion ................................................................................................. 10
for C-Tine Conversion ................................................................................................. 11
Wing Linkage Bracket Comparison by Tine Style ............................................................... 13
Addition of New Linkage Parts - Wings
for S-Tine Conversion ................................................................................................. 14, 15
for C-Tine Conversion ................................................................................................. 16, 17
Installation of HYDRAULICS
for ML PULVIMULCHERS ........................................................................................... 18
for WL PULVIMULCHERS ........................................................................................... 19
9J223 3
10-31-07 Page 1
9J223
3
2
4
6
1
5
87
KLIK PIN
re-insert
after angles
are removed
LEVELING BAR
REAR TOOTH BAR
S-TINE
Re-insert the Pin, Flat Washers, Cotter Pins,
U-bolts, Lock Washers, and Hex Nuts after
Tooth Linkage and related components
have
been moved to the right. See next illustration
Front Angle Brackets
will be moved to right.
See next illustration
FRONT TOOTH BAR
CenterRemoveS-Tine
FRONT
TOOTH LINKAGE
move to right
S-TINE
If the following parts are installed, remove from Center Frame
Item Part Number Qty Description Weight
1 9J114 1 REAR BRACKET S-TINE 20.70
2 5J768 1 PIN,1.0 x 5.50 H2 1.18
3 4C858 2 ROLL PIN,5/16 x 2,ZP 0.02
4 9J144 1 LINK,S-TINE RH 11.28
5 9J143 1 LINK,S-TINE LH 11.28
6 2J094 2 U-BLT,5/8-11 x 2-5/8 x 3-3/8,ZP 0.66
7 1B166 4 WASHER,LOCK 5/8,ZP 0.03
8 1C392 4 NUT,HEX 5/8-11,ZP 0.07
CenterRemoveS-Tine
Page 4
9J223Page 210-31-07
3
2 4
6
1
5
8
7
LEVELING BAR
REAR TOOTH BAR
C-TINE
Re-insert Pin, Flat Washers, and
Cotter Pins, after
Tooth Linkage
and related components
have
been moved to the right.
See next illustration
LH
Front Angle Brackets and related
hardware
will be repositioned to
the right. See next illustration
FRONT TOOTH BAR
CenterRemoveC-Tine
FRONT
TOOTH LINKAGE
move to right
KLIK PIN
re-insert
after angles
are removed
C-TINE
If the following parts are installed, remove from Center Frame
Item Part Number Qty Description Weight
1 9J107 1 REAR BRACKET C-TINE 16.20
2 5J768 1 PIN,1.0 x 5.50 H2 1.18
3 4C858 2 ROLL PIN,5/16 x 2,ZP 0.02
4 9J146 1 LINK,C-TINE RH 11.70
5 9J145 1 LINK,C-TINE LH 11.70
6 2J094 2 U-BLT,5/8-11 x 2-5/8 x 3-3/8,ZP 0.66
7 1B166 4 WASHER,LOCK 5/8,ZP 0.03
8 1C392 4 NUT,HEX 5/8-11,ZP 0.07
CenterRemoveC-Tine
9J223 5
10-31-07 Page 3
9J223
This Page Intentionally Blank
Page 6
9J223Page 410-31-07
INDEPENDENT
REAR TOOTH
BRACKET
REAR FRAME TUBE
REAR BRACKET
HYDRAULIC
CYLINDER OR
RATCHET JACK
S-TINE
FRONT TOOTH
BRACKET
CENTER FRAME S-TINE LINKAGE
CENTER FRAME C-TINE LINKAGE
HYDRAULIC
CYLINDER OR
RATCHET JACK
REAR BRACKET
INDEPENDENT
REAR TOOTH
BRACKET
FRONT TOOTH
BRACKET
C-TINE
REAR FRAME TUBE
CENTER FRAME BRACKET RELATIONSHIP PER TINE STYLE
CenterSide
9J223 7
10-31-07 Page 5
9J223
Loading...