Landmann 470106 Assembly And Operating Instructions Manual

VER. 7, 7/28/2017

Assembly and Operating

Instructions for Model:

470106

Pellet Kettle Grill

Please read this entire manual

before assembling and using this

pellet fuel burning appliance.

Failure to follow these

instructions could result in

property damage, bodily injury or

even death.

Contact local building or ﬁre

ofﬁcials about restrictions and

installation inspection

requirements in your area.

Please save this instruction

manual for future reference.

!

A MAJOR CAUSE OF FIRES IS FAILURE

TO MAINTAIN REQUIRED CLEARANCES

(AIR SPACES) TO COMBUSTIBLE

MATERIALS. IT IS OF UTMOST

IMPORTANCE THAT THIS PRODUCT BE

INSTALLED ONLY IN ACCORDANCE

WITH THESE INSTRUCTIONS.

Appliance Type: Pellet Fuel Burning Cooking Appliance Test Standards

Conforms To: UL Subject 2728 Certiﬁed To: ULC/ORD STD C2728

5009323

®

PAGE 2

• WARNING! THE GRILL IS FOR OUTDOOR USE ONLY!

• WARNING! NEVER USE GASOLINE, GASOLINE-TYPE FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR SIMILAR LIQUIDS TO START OR "FRESHEN UP" A FIRE IN THIS APPLIANCE. KEEP ALL SUCH LIQUIDS AWAY FROM THE APPLIANCE WHEN IN USE.

• DO NOT STORE FLAMMABLE LIQUIDS OR MATERIALS ON THE BOTTOM SHELF OR SIDE SHELF.

• THE GRILL IS FOR ADULT USE ONLY.

• WARNING! THIS GRILL GETS EXTREMELY HOT DURING USE! USE EXTREME CAUTION AROUND THE GRILL.

• USE CAUTION WHEN OPENING THE LID AS HOT STEAM OR A FLARE UP COULD CAUSE BURNS.

• KEEP THE GRILL A MINIMUM OF 24 IN. AWAY FROM BUILDINGS, STRUCTURES, ANY FLAMMABLE ITEMS AND VEHICLES DURING USE.

• KEEP CHILDREN AND PETS AWAY WHILE THE GRILL IS BEING USED.

• USE CAUTION AFTER THE FIRE HAS BEEN EXTINGUISHED- SURFACES WILL REMAIN HOT FOR SOME TIME.

• WARNING! NEVER PUT YOUR FINGERS IN THE AUGER CHANNEL FOR ANY REASON!

• THE HOPPER PELLET FUEL SCREEN MUST BE IN PLACE DURING USE.

• NEVER USE THE GRILL UNDER COVERED PORCHES, AWNINGS, COMBUSTIBLE CEILINGS, LOW HANGING TREE BRANCHES, TRELLIS, OR OVERHANGS OF ANY KIND.

• NEVER USE INSIDE ENCLOSED AREAS SUCH PATIOS, GARAGES, ENCLOSED ROOMS, BUILDINGS OR TENTS.

• DO NOT USE IN WINDY CONDITIONS.

• DO NOT USE IN VERY WET OR RAINY CONDITIONS.

• KEEP THE LID CLOSED DURING USE. THIS PELLET GRILL IS INTENDED TO BE USED WITH A CLOSED LID.

• NEVER USE THIS GRILL AS A HEATER.

• THIS GRILL IS NOT FOR COMMERCIAL USE.

• BEFORE STARTING, MAKE SURE THE GREASE BUCKET IS IN PLACE.

• ALWAYS UNPLUG GRILL AFTER USING. WIND CORD AROUND THE CORD WRAP SO IT IS OUT OF THE WAY.

• DURING USE, THE PLUG WIRING SHOULD BE SORTED SO IT DOES NOT IMPOSE A TRIPPING HAZARD.

• ALWAYS USE THE GRILL ON A HARD, STABLE AND LEVEL SURFACE.

• THIS GRILL OPERATES AUTOMATICALLY THROUGH THE CONTROL PANEL. DO NOT MANUALLY FILL THE FIRE POT OR OVER-FILL THE FIRE POT BY HAND. THIS WILL CAUSE A DANGEROUS OVER-FIRING CONDITION.

READ FIRST! RULES FOR PELLET KETTLE GRILL SAFE OPERATION.

®

• THE SIDE SHELF CAN HOLD 15 LBS. SAFELY, DO NOT

PUT MORE THAN 15 LBS. ON THE SIDE SHELF.

• DO NOT LEAN OR PUSH DOWN ON THE SIDE SHELF.

• DO NOT MOVE THE GRILL WHILE IT IS BEING USED.

• DO NOT USE ACCESSORIES NOT SPECIFIED FOR USE

WITH THIS APPLIANCE.

• MAKE SURE THE FRONT WHEEL CASTERS ARE

LOCKED WHILE IN USE.

• DO NOT LEAVE UNATTENDED AT ANY TIME WHILE

IN USE.

• BEFORE EACH USE, MAKE SURE THE GRILL IS IN

GOOD WORKING CONDITION.

• DO NOT ALTER THE GRILL IN ANY WAY.

• DO NOT MODIFY OR HARDWIRE THE AUGER TO

RUN CONTINUOUSLY.

• DO NOT USE THE GRILL UNTIL IT IS COMPLETELY ASSEMBLED WITH ALL PARTS SECURELY TIGHTENED.

• THE GRILL MUST BE COMPLETELY COOLED OFF AND MUST BE EXTINGUISHED BEFORE ANY COVER CAN BE USED.

• MAINTAINING THE GRILL IS THE RESPONSIBILITY OF THE OWNER OR USER. THE FIREBOWL, DRIP TRAY AND DRIP TRAY TUBE MUST BE CLEANED OCCASIONALLY TO REMOVE GREASE BUILDUP. FAILURE TO CLEAN GREASE BUILDUP CAN CAUSE GREASE FIRES WHICH ARE VERY DANGEROUS.

• WARNING! AFTER EVERY 20 HRS OF USE, THE FIRE POT MUST BE CLEANED OUT TO REMOVE ANY ASH BUILDUP. THIS IS REQUIRED MAINTENANCE.

• NEVER POUR WATER INTO THE FIREBOWL, FIRE POT OR DRIP TRAY.

• IF A GREASE FIRE WERE TO OCCUR, BAKING SODA CAN BE USED TO EXTINGUISH THE FIRE. USE EXTREME CAUTION NOT TO BURN YOURSELF.

• IF THE FIRE DOES NOT EXTINGUISH, REMOVE THE FOOD IF POSSIBLE. KEEP THE LID CLOSED, CLOSE THE CHIMNEY DAMPER AND PRESS THE POWER BUTTON TO OFF.

• ONCE THE FIRE IS EXTINGUISHED, CLEAN THE GREASE BUILDUP BEFORE COOKING IS RESUMED.

• DISPOSAL OF ASHES - ANY ASHES THAT ARE REMOVED FROM THE GRILL SHOULD BE PLACED IN A METAL CONTAINER WITH A TIGHT FITTING LID. THE CLOSED CONTAINER OF ASHES SHOULD BE PLACED ON A NONCOMBUSTIBLE FLOOR OR GROUND, WELL AWAY FROM ALL COMBUSTIBLE MATERIALS, PENDING FINAL DISPOSAL. IF THE ASHES ARE DISPOSED OF BY BURIAL IN SOIL OR OTHERWISE LOCALLY DISPERSED, THEY SHOULD BE RETAINED IN THE CLOSED CONTAINER UNTIL ALL CINDERS HAVE THOROUGHLY COOLED.

PAGE 3

READ FIRST! RULES FOR PELLET KETTLE GRILL SAFE OPERATION.

CARBON MONOXIDE HAZARD!

BURNING WOOD OR CHARCOAL PRODUCES CARBON MONOXIDE, WHICH HAS NO ODOR AND CAN CAUSE DEATH IF BURNED IN ENCLOSED AREAS. NEVER BURN WOOD OR CHARCOAL INSIDE HOMES, VEHICLES, TENTS OR ANY OTHER ENCLOSED AREAS.

NOTE THE FOLLOWING TO PREVENT THIS COLORLESS, ODORLESS GAS FROM POISONING YOU, YOUR FAMILY OR OTHERS:

• KNOW THE SYMPTOMS OF CARBON MONOXIDE POISONING: HEADACHE, DIZZINESS, WEAKNESS, NAUSEA, VOMITING, SLEEPINESS, AND CONFUSION. CARBON MONOXIDE REDUCES THE BLOOD'S ABILITY TO CARRY OXYGEN. LOW BLOOD OXYGEN LEVELS CAN RESULT IN LOSS OF CONSCIOUSNESS AND DEATH.

• SEE A DOCTOR IF YOU OR OTHERS DEVELOP COLD OR FLU-LIKE SYMPTOMS WHILE COOKING OR IN THE VICINITY OF THIS APPLIANCE. CARBON MONOXIDE POISONING, WHICH CAN EASILY BE MISTAKEN FOR A COLD OR FLU, IS OFTEN DETECTED TOO LATE.

• CARBON MONOXIDE IS ESPECIALLY TOXIC TO MOTHER AND CHILD DURING PREGNANCY, INFANTS, THE ELDERLY, SMOKERS, AND PEOPLE WITH BLOOD OR CIRCULATORY SYSTEM PROBLEMS, SUCH AS ANEMIA OR HEART DISEASE.

WOOD DUST AND FUELS USED IN WOOD BURNING APPLIANCES, AND THE PRODUCTS OF COMBUSTION OF SUCH FUELS, CONTAIN CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

IT IS GOOD PRACTICE TO ALWAYS HAVE A WELL MAINTAINED FIRE EXTINGUISHER AVAILABLE WHENEVER ANY TYPE OF GRILL IS BEING USED.

WARNING!

!

WARNING!

!

• USE ONLY FOOD GRADE HARDWOOD PELLETS

MADE FOR PELLET GRILLS.

• DO NOT USE HEATING PELLETS WHICH MAY

CONTAIN HAZARDOUS CONTAMINANTS.

• IT IS RECOMMENDED THAT EXCESS PELLETS ARE NOT STORED IN THE HOPPER FOR EXTENDED PERIODS AS THEY CAN ABSORB MOISTURE CAUSING THE AUGER TO SEIZE.

• IF THE PELLETS ARE GOING TO BE STORED IN THE BAG THEY WERE PURCHASED IN, CLOSE THE BAG TIGHTLY AND PLACE IN A DRY LOCATION. A BETTER CHOICE IS A MOISTURE PROOF SEALED CONTAINER. CARE MUST BE TAKEN TO INSURE THE PELLET FUEL IS KEPT FROM ALL MOISTURE.

• DO NOT USE PELLETS THAT HAVE GOTTEN WET. DO NOT USE PELLETS THAT HAVE BECOME EXCESSIVELY POWDERY OR DUSTY. THIS IS A SIGN THE PELLETS ARE DEFECTIVE OR HAVE BEEN EXPOSED TO MOISTURE AT SOME TIME.

FUEL

!

• KEEP THE GRILL A MINIMUM OF 24 IN. AWAY FROM

BUILDINGS, STRUCTURES, ANY FLAMMABLE ITEMS AND VEHICLES DURING USE.

• NEVER USE THE GRILL UNDER COVERED PORCHES,

AWNINGS, COMBUSTIBLE CEILINGS, LOW HANGING TREE, BRANCHES, TRELLIS, OR OVERHANGS OF ANY KIND.

• IT IS RECOMMENDED THAT THE APPLIANCE BE

INSTALLED ON NONCOMBUSTIBLE FLOORS. THE APPLIANCE CAN BE INSTALLED ON COMBUSTIBLE FLOORS WITH A NONCOMBUSTIBLE SURFACE WHERE THE PROTECTIVE SURFACE HAS BEEN APPROVED FOR SUCH USE BY THE AUTHORITY HAVING JURISDICTION.

DO NOT USE THIS APPLIANCE UNDER

OVERHEAD COMBUSTIBLE SURFACES.!

WARNING!

!

OUTDOOR USE ONLY

®

HARDWARE AND SMALL PART LISTING

PAGE 4

x 15

(15) M6 x 12MM

BOLT

(8) M8 x 15MM

HEXBOLT

(12) M6 FLANGE

HEXNUT

(2) M10 LOCKING

HEXNUT

(4) 20MM WASHER

AA

AB

AC AE AF

x 8

x 12 x 2 x 4

®

ASSEMBLED PARTS

PAGE 5

A

(1) MAIN GRILL ASSEMBLY

B

(1) LID

F

(1) BOTTOM SHELF

C

(2) FRONT LEGS

D

(1) RIGHT BACK LEG

E

(1) LEFT BACK LEG

K

(1) LID HANDLE

L

(1) CHIMNEY ASSEMBLY

H

(1) COVER

®

ASSEMBLED PARTS

PAGE 6

M

(1) HEAT DIFFUSER

N

(1) DRIP TRAY

P

(1) COOKING GRATE

Q

(1) GREASE BUCKET

R

(1) MEAT PROBE

S

(2) LOW GREASE TRAY

HOLDERS

T

(1) HIGH GREASE

TRAY HOLDER

V

(2) WHEELS

W

(2) WHEEL COVERS

X

(1) WHEEL AXLE

®

EXPLODED VIEW FOR ASSEMBLED PARTS

PAGE 7

F

A

B

C

E

P

Q

R

M

L

N

V

T

S

D

K

X

W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

A. B. C. D. E. F. H. K. L. M. N. P. Q. R. S. T. V. W. X.

PELLET KETTLE PARTS QTY

MAIN GRILL ASSEMBLY LID FRONT LEGS RIGHT BACK LEG LEFT BACK LEG BOTTOM SHELF COVER LID HANDLE CHIMNEY ASSEMBLY HEAT DIFFUSER DRIP TRAY COOKING GRATE GREASE BUCKET MEAT PROBE LOW DRIP TRAY HOLDERS HIGH DRIP TRAY HOLDER WHEELS WHEEL COVERS WHEEL AXLE

®

PELLET KETTLE

ASSEMBLY INSTRUCTIONS

STEP 1: ASSEMBLE THE LEGS

Assembly time: 45 minutes

A Phillips or plain screwdriver and adjustable wrench are needed for assembly.

Very carefully turn the main grill assembly [ A ] over.

Assemble the (2) front legs [ C ] to the main grill using (4) hexbolts [ AB ]. Tighten securely.

Assemble the (2) back legs [ D,E ] to the main grill using (4) hexbolts [ AB ]. Tighten securely.

DO NOT RETURN PRODUCT TO THE STORE.

IF YOU HAVE QUESTIONS OR HAVE

TROUBLE WITH ASSEMBLY, PLEASE CALL

1-877-347-4557 FOR ASSISTANCE.

A

D

C

E

X

W

STEP 2: ASSEMBLE THE WHEEL AXLE

AND THE WHEELS

Insert the wheel axle [ X ] through the back leg holders. To assemble the wheels [ V ], slide (1) washer [ AF ] onto each side of the axle. Slide the wheels on the axle, a washer [ AF ] and secure each wheel with a locking hexnut [ AE ].

Align the wheel cover [ W ] pins with the wheels and snap in place.

AB

AF

V

AF

AE

2

STEP

1

STEP

PAGE 8

®

DO NOT RETURN PRODUCT TO THE STORE.

IF YOU HAVE QUESTIONS OR HAVE

TROUBLE WITH ASSEMBLY, PLEASE CALL

1-877-347-4557 FOR ASSISTANCE.

PELLET KETTLE

ASSEMBLY INSTRUCTIONS

STEP 3: ASSEMBLE BOTTOM SHELF

Align the bottom shelf [ F ] with the tabs on the legs and assemble with (4) 12MM bolts [ AA ] and (4) M6 ﬂange hexnuts [ AC ]. Tighten bolts securely.

AC

TAB

PAGE 9

3

STEP

AA

F

®

STEP 5: ASSEMBLE THE LOCKING RING

Insert the temperature probe through the slot on the lid [ B ]. See STEP 4A.

Assemble the lid to the hinge using (2) 12MM bolts [ AA ] and (2) M6 ﬂange hexnuts [ AC ].

Assemble the temperature probe using (1) 12MM bolt [ AA ] and (1) M6 ﬂange hexnut [ AC ]. Align the probe so the tip is pointing upwards. See STEP 4B.

Add cooking oil to the pins and hinge. SEE STEP 4C.

STEP 4: ASSEMBLE LID AND

TEMPERATURE PROBE

PELLET KETTLE

ASSEMBLY INSTRUCTIONS

PAGE 10

AA

AC

B

AC

TEMPERATURE PROBE

4

STEP

4C

STEP

ADD COOKING OIL TO THE MOVING PINS AND PIVOTING BOLTS ON THE HINGE.

NOTE

TEMPERATURE PROBE

4A

STEP

TEMPERATURE PROBE

4B

STEP

®

Landmann 470106 Assembly And Operating Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual