Page 1
LANCOM WLC-4006+
VPN
Online
LANCOM WLC-4006+
AP Status
ETH 1
ETH 2
ETH 3
ETH 4
Uplink
Quick Reference Guide
4
Please observe the
following when setting
up the device
a For devices to be
operated on the
desktop, please attach
the adhesive rubber
footpads
a Do not rest any objects
on top of the device
Power
a Keep the ventilation
slots on the side of
the device clear of
obstruction
a In case of wall
mounting, use the
drilling template as
supplied
LANCOM 1681V
VDSL
ISDN Status
ETH 2
VPN
ETH 3
ETH 4
Online
ETH 1
a
Uplink interface
Connect the Uplink interface
to a LAN switch or a WAN
modem with a suitable cable.
b ca d e
b
Ethernet interface
Use the cable with the
kiwi-colored connectors to
connect one of the interfaces
ETH 1 to ETH 4 to your PC or
a LAN switch.
c
Serial interface
You can connect the device
to a PC with a conguration
cable (cable sold separately).
d
USB interface
You can use the USB interface
to connect a USB printer or
a USB ash drive for device
conguration.
e
Power
When connecting the cable to
the device, turn the bayonet
connector 90° clockwise until
it clicks into place.
a db fec
a Power
Off Device switched off
Green, permanently Device operational
Green/orange, blinking Conguration password not set. Without a
conguration password, the conguration
data in the device is unprotected.
Red, blinking Charge or time limit reached
b AP Status
Green, permanently At least one active access point is con-
nected and authenticated; no new and no
missing access point.
Green/orange, blinking At least one new access point.
Red, permanently The LANCOM Wi-Fi controller is not yet
operational; one of the following elements
is missing:
a Root certicate
a Device certicate
a Current time
a Random number for the DTLS encryption
Red, blinking At least one of the expected access points
is missing.
c Uplink
Off No networking device attached
Green, permanently Connection to network device operational,
no data trafc
Green, ickering Data transmission
d ETH
Off No networking device attached
Green, permanently Connection to network device operational,
no data trafc
Green, ickering Data transmission
e Online
Off WAN connection inactive
Green, permanently WAN connection active
Red, permanently WAN connection error
f VPN
Off No VPN connection active
Green, permanently VPN connection active
Green, blinking Establishing VPN connections
Hardware
Power supply 12 V DC, external power adapter (110 or 230 V) with bayonet connector to secure against
disconnection
Power consumption 8.5 W
Environment Temperature range 0–40 °C; humidity 0–95 %; non-condensing
Housing Robust synthetic housing, rear connectors, ready for wall mounting, Kensington lock; measures
210 x 45 x 140 mm (W x H x D)
Number of fans None; fanless design, no rotating parts, high MTBF
Interfaces
ETH 4 individual ports, 10 / 100 / 1000 Mbps Gigabit Ethernet.
Each Ethernet port can be freely congured (LAN, WAN, monitor port, off). LAN ports operate
in switch mode or isolated. Additionally, external DSL modems or termination routers can be
operated at the Uplink port together with policy-based routing.
USB USB 2.0 Hi-Speed host port for connecting USB printers (USB print server) or USB data media
(FAT le system)
Cong (Com) Serial conguration interface / COM port (8-pin Mini-DIN): 9,600 - 115,000 baud, suitable for
optional connection of analog / GPRS modems. Supports the internal COM-port server.
Uplink 10 / 100 / 1000 Mbps Gigabit Ethernet
WAN protocols
Ethernet PPPoE, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and plain Ethernet (with or without DHCP),
RIP-1, RIP-2, VLAN, IP, GRE, L2TPv2 (LAC or LNS), IPv6 over PPP (IPv6 and IPv4/IPv6 Dual Stack
Session), IP(v6)oE (autoconguration, DHCPv6 or static)
Declaration of Conformity
Hereby, LANCOM Systems declares that this device is in compliance with Directives 2014/30/EU and 2014/35/EU.
The full text of the EU declaration of conformity is available at the following internet address:
www.lancom-systems.com/ce/
Package content
Documentation Quick Reference Guide (DE/EN), Installation Guide (DE/EN), FCC leaet (US version only)
Cable Ethernet cable, 3m (kiwi-colored connectors)
WLC Public Spot Function included in rmware
Power adapter External power adapter, NEST 12 V / 1.5 A DC/S, coaxial power connector 2.1 / 5.5 mm
bayonet,
LANCOM item no. 110723 (EU, 230 V), or LANCOM item no. 110829 (UK, 230 V), or
LANCOM item no. 111007 (US, 110 V)
trademarks of their owners. Subject to change without notice. No liability for technical errors and/or omissions. 111639/0717
LANCOM, LANCOM Systems and LCOS are registered trademarks. All other names or descriptions used may be trademarks or registered
Cloud-ready
a Rack installation with
the optional LANCOM
Rack Mount (not
supplied)
Use only the supplied power
adapter.
SETTING UP AND CONNECTING THE DEVICE
TECHNICAL DATA
Loading...