Lancom GE PoE+ Injector User Manual

Page 1
Software & Accessories
LANCOM GE PoE+ Injector
Injector for powering LANCOM access points by Power over Ethernet
The LANCOM GE PoE+ Injector offers compelling flexibility and performance: The ability to power access points
up to 100m away facilitates a flexible positioning of the access points for perfect signal coverage. The PoE+
standard IEEE 802.3at allows even high-power devices to operate without any loss of performance. The
cost-effective solution for companies requiring PoE-enabled networks.
a
1-port PoE Injector with Gigabit Ethernet support
a
a
Power supply through up to 100m of Ethernet cable
a
Auto-sensor for PoE-device detection
a
Easy plug & play installation
Page 2
DATASHEET
LANCOM GE PoE+ Injector
Gigabit Ethernet support
Even where a PoE-enabled switch is not in use, Gigabit
Ethernet access points are reliably powered by the LANCOM
GE PoE+ Injector. Access points that are far away from a
regular power outlet continue to offer Gigabit performance
without performance loss.
Full power thanks to PoE and PoE+
As it supports both of the PoE standards IEEE 802.3af and
IEEE 802.3at, the Injector is the optimal choice for powering
all of your LANCOM access points by means of Power over
Ethernet. Even high-performance products operate without
performance loss.
High output power
With power supplied as per IEEE 802.3af/at with a
guaranteed power output of 30W over up to 100m, the
LANCOM GE PoE+ Injector gives you the flexibility to position
your access points for perfect signal coverage.
Automatic detection of PoE devices
PoE devices connected to the LANCOM GE PoE+ Injector are
detected by an auto-sensor algorithm and the energy-efficient
power supply is activated with the necessary voltage.
Integrated power supply unit
Thanks to the power supply unit integrated into the LANCOM
GE PoE+ Injector, the rubber connector supplied with it is
the only additional component you needa space-saving
solution.
Plug & play
The Injector works with a convenient plug & play installation
for quick and easy integration into the network. Simply
connect the LANCOM GE PoE+ Injector between the switch
and the access point and use the power cord to supply
electricity.
Page 3
DATASHEET
LANCOM GE PoE+ Injector
Interfaces
10/100/1000 Mbit/s, PoE compliant with IEEE 802.3af and IEEE 802.3atLAN
Hardware
100 to 240 V AC, 50 to 60 HzAC Input Voltage anf AC Frequency
0,8 A at 110-220 V ACAC Input Current
55 VOutput Voltage
30 W min.Output power
Output 4/5(+), 7/8(-)Pin Assignment and Polarity
53 mm (W) x 32.5 mm (H) x 140 mm (L) 0,8 lbs (350g)Dimensions & Weight
AC Power (green) User Indicator: Channel Power (green)Indicators System Indicator
Shielded RJ-45, EIA 568A and 568BConnectors
Environment
Declarations of conformity*
Scope of delivery
Support
Item number(s)
Operating Ambient Temperature @30W: -4° F to 104° F (-20° C to 40° C), Operating Ambient Temperature @22.5W: -4°F to 131°F (-20°C to 55°C), Operating Humidity: Maximum 90%, non-condensing, Storage Temperature: -4° F to 158° F (-20° C to 70° C), Storage Humidity: Maximum 95%, non-condensing Operating Altitude: -1000 to 10,000ft (-304.8m to 3048m)
1,01 lbs (460 g)Weight (complete product incl. packaging)
GS Mark per EN 60950Safety Approvals
FCC Part 15, Class B with FTP cablingFCC
You will find all declarations of conformity in the products section of our website at www.lancom-systems.eu*) Note
Printed Installation Guide (DE/EN)Manual
IEC power cordCable
2 years, support via hotline and Internet KnowledgeBaseWarranty
61738LANCOM GE PoE+ Injector (EU)
61739LANCOM GE PoE+ Injector (UK)
Loading...