Lamotte PHOSPHATE KIT User Manual
PHOSPHATE KIT
OCTA-SLIDE 2, 0.5-10 ppm
CODE 3114-02
QUANTITY CONTENTS CODE
2 x 30 mL *Phosphate Acid Reagent *V-6282-G
5 g Phosphate Reducing Reagent V-6283-C
2 Test Tubes, 10.0 mL, glass, w/caps 0843
1 Spoon, 0.1 g 0699
2 Pipets, 1.0 mL, plastic 0354
1 Demineralizer Bottle 1151
1 Phosphate Octa-Slide 2 Bar, 0.5-10 ppm 3115-01
1 Octa-Slide 2 Viewer 1101
*WARNING: Reagents marked with an * are considered to be potential health hazards.
To view or print a Safety Data Sheet (SDS) for these reagents go to www.lamotte.com.
Search for the four digit reagent code number listed on the reagent label, in the contents
list or in the test procedures. Omit any letter that follows or precedes the four digit
code number. For example, if the code is 4450WT-H, search 4450. To obtain a printed
copy, contact LaMotte by email, phone or fax.
Emergency information for all LaMotte reagents is
available from Chem-Tel: (US, 1-800-255-3924)
(International, call collect, 813-248-0585).
To order individual reagents or test kit components,
Warning! This set contains chemicals
that may be harmful if misused. Read
cautions on individual containers
carefully. Not to be used by children
except under adult supervision.
use the specifi ed code number.
NOTES:
• This test determines levels of Orthophosphates only.
• This test should be run on clear samples only.
• Best results are obtained when solution temperatures are 23-25°C.
USE OF THE OCTA-SLIDE 2 VIEWER
The Octa-Slide 2 Viewer should be held so nondirect light enters through the back of the Viewer.
Insert the Octa-Slide 2
the reacted sample into the top of the Viewer. Match
the color of the
Bar into the Viewer. Insert
reaction to the color standards.
PROCEDURE
RANGE: 0.5-10 ppm PHOSPHATE (PO
)
4
1. Insert the Phosphate Octa-Slide 2 Bar (3115-01) into the Octa-Slide 2 Viewer
(1101).
2. Fill a test tube (0843) to 10 mL line with sample water.
3. Use a 1.0 mL pipet (0354) to add 1.0 mL of *Phosphate Acid Reagent (6282).
Cap and mix.
4. Use a 0.1 g spoon (0699) to add one level measure of Phosphate Reducing
Reagent (6283). Cap and mix until dissolved. Wait 5 minutes.
5. Insert the test tube into the Octa-Slide 2 Viewer. Match sample color to a color
standard. Record as ppm Phosphate.
RANGE: 5-100 ppm PHOSPHATE (PO4), 1:10 DILUTION
1. Insert the Phosphate Octa-Slide 2 Bar (3115-01) into the Octa-Slide 2 Viewer
(1101).
2. Use a 1.0 mL pipet (0354) to add 1.0 mL of sample water to test tube (0843).
3. Dilute to 10 mL line with deionized water from the Demineralizer Bottle (1151).
4. Use a second 1.0 mL pipet (0354) to add 1.0 mL *Phosphate Acid Reagent
(6282). Cap and mix.
5. Use the 0.1g spoon (0699) to add one level measure of Phosphate Reducing
Reagent (6283). Cap and mix until dissolved. Wait 5 minutes.
6. Insert the test tube into the Octa-Slide 2 Viewer. Match sample color to a color
standard. Record as ppm Phosphate.
LaMOTTE COMPANY
Helping People Solve Analytical Challenges
800-344-3100 • 410-778-3100 (Outside U.S.A.) • Fax 410-778-6394
PO Box 329 • Chestertown • Maryland • 21620 • USA
Visit us on the web at www.lamotte.com
63114-02 11/19
Loading...