Revo 2436
Owner’s Manual
Revo 2436
MLAREVO2436220
lagunatools.com | lagunacleanair.com | supermaxtools.com
Registration
To prevent voiding this warranty, all products sold must be registered within thirty (30) days of receiving the product. All
registered purchases will receive notications about important product changes, receive customer service, and be able to
le a warranty claim against defective workmanship, parts, or materials.
You must register your purchase! Please follow this link:
https://lagunatools.com/policies/warranty/
Length of Warranty
All new machines and optional accessories sold through an authorized dealer carry a two-year warranty eective the date of
receiving the product. Machines sold for either commercial or industrial use have a one-year warranty. Wearable parts like
throat plates, band-saw guides, etc., have a ninety-day warranty.
Aside from being free of defects upon receiving, consumable parts, like cutters and abrasives, are not covered by this
warranty unless otherwise stated by Laguna Tools. These parts are designed to be used at the expense of the operator and
are available for replacement or inventory purchase. The determination of a consumable part will be made on a case-by-case
basis by Laguna Tools.
2 Year – New Machines Sold Through an Authorized Dealer
2 Year – Accessories Sold as Machine Options (excluding blades)
1 Year – Machines Sold for Commercial or Industrial Use
1 Year – Blades and Accessories outside of Machine Options
90 Days – Wearable Parts
Who is Covered
The applicable warranty covers only the initial purchaser of the product from the date of receiving the product. To le such
claims, the original purchaser must present the original receipt as proof of purchase.
What is Covered
The warranty covers any defects in the workmanship of all parts and materials that make up the machine unless otherwise
specied. Any part, determined by Laguna Tools®, to have a defect will be repaired or replaced (and shipped), without
charge. The defective item must be returned to Laguna Tools with the complaint and proof of purchase and in the original
packaging. In the event the item is determined to be not covered by this warranty, the customer will be responsible for the
cost to replace the item/part and all related shipping charges.
Warranty Limitations
This limited warranty does not apply to natural disasters, acts of terrorism, normal wear and tear, product failure due to lack
of maintenance or cleaning, damage caused by accident, neglect, or inadequate dust collection. The warranty may be
voided against proof of misuse/abuse, damage caused where repair or alterations have been made or attempted by others,
using the product for purposes other than those described as intended use (unless with consent by Laguna Tools®), modication to the product, or use with an accessory that was not designed for the product. It is the responsibility of the user to
understand basic woodworking machinery settings and procedures and to properly maintain the equipment in accordance
with the standards provided in this manual.
Shipping Damage
Laguna Tools® is not responsible for damage or loss caused by a freight company or other circumstances not in the direct
control of Laguna Tools. All shipping-related claims for loss or damage goods must be made to Laguna Tools within twenty-four hours of delivery.
How to Receive Support
To le a warranty claim, please contact the warranty department at 1-949-474-1200. To receive customer service or technical
support please contact the customer service department at 1-800-332-4094. Warranty parts are shipped at the expense of
Laguna Tools either by common carrier, FedEx ground services or similar method. Technical support to install replacement
parts is primarily provided by phone, fax, email, or the Laguna Tools Customer Support Website.
2072 Alton Parkway Irvine, CA 92606 U.S.A.
For Customer Service: +1 (949) 474-1200 or email customerservice@lagunatools.com
825 Bistline Drive, West Columbia, SC 29172 U.S.A
Dear Craftsman:
Thank you for your purchase and welcome to the Laguna Tools group of
discriminating craftsman. I understand that you have a choice of where to
purchase your machines and appreciate the confidence you have in our
products.
Every machine sold by Laguna Tools has been carefully designed and well
thought through from a woodworker’s perspective. I cut on our bandsaws,
lathes, table saws, combination machines, and CNC routers and Plasma
machines. Through my hands-on experience, I work hard to make our machines
better. I strive to give you machines that inspire you to create works of art;
machines that are a joy to run and work on; machines that encourage your
performance.
Today, we offer high-performance machines with innovative solutions that meet
the needs of Craftsman and their ever-evolving craft.
I started Laguna Tools as a woodworker and craftsman; I still am and more.
Thank you again for becoming a Laguna Tools customer.
Torben Helshoj
President and Founder -Laguna Tools
Imagination, Innovation and Invention at Work.
2
Page number
Safety Rules
4
Warranty
8
Noise emission
9
Specification sheet
10
Receiving your machine
11
Introduction to your machine
12
Parts of the machine
12
What you will receive with the machine
17
Where to locate your machine
19
Unpacking your machine
19
Assembly and setup
21
Maintenance
33
Troubleshooting
36
Electrical drawing
38
Exploded view drawings
41
Table of contents.
3
4
5
6
Wooden safety cover
Padlocks
Wooden safety cover
Padlocks
Plastic safety cover
Padlocks
Plastic safety cover
Padlocks
Locking the lathe
It is strongly recommended that the lathe is never left unattended in the unlocked condition.
To lock the machine it is recommended that a cover (not supplied) is made to lock the control
panel. We have supplied two concepts for locking the panel (see below). The cover can be
made from wood or plastic, two covers (not supplied) are made to lock the control panels on
both headstock and remote controller. We have supplied four concepts for locking the control
panel (see below).
First, push down the emergency stop. Then lock the cover together by putting padlocks [not
included] on the two handles on the control panel. To safeguard your machine from
unauthorized operation and accidental starting by young children, the use of padlocks is
strongly recommended.
7
Limited Warranty.
New woodworking machines sold by Laguna Tools carry a one-year warranty from the date of
shipping. Laguna Tools guarantees all new machines sold to be free of manufacturer's
defective workmanship, parts, and materials.
We will repair or replace, without charge, any parts determined by Laguna Tools, Inc. to be a
manufacturer's defect. We require the defective item/part to be returned to Laguna Tools. In
the event the item/part is determined to be
damaged due to lack of maintenance, cleaning or misuse/abuse, the customer
will be responsible for the cost to replace the item/part, plus all related shipping charges.
This limited warranty does not apply to natural disasters, acts of
terrorism, normal wear and tear, product failure due to lack of maintenance or cleaning,
damage caused by accident, neglect, lack of or inadequate dust
collection, misuse/abuse or damage caused when repair or alterations have
been made or attempted by others.
Laguna Tools, Inc. is not responsible for additional tools or modifications sold or performed
(other than from/by Laguna Tools, Inc.) on any Laguna Tools, Inc. woodworking machine.
Warranty may be voided upon the addition of such noted tools and/or modifications,
determined on a case-by-case basis.
Normal user alignment, adjustment, tuning and machine settings are not
covered by this warranty. It is the responsibility of the user to understand
basic woodworking machinery settings and procedures and to properly maintain the
equipment in accordance with the standards provided by the manufacturer.
Parts, under warranty, are shipped at Laguna Tools, Inc's cost either by
common carrier, FedEx Ground service or a similar method.
Technical support to install replacement parts is primarily provided by phone, fax, or e-mail.
The labor required to install replacement parts is the responsibility of the user.
Laguna Tools is not responsible for damage or loss caused by a freight company or other
circumstances not in our control.
Only new machines sold to the original owner are covered by this warranty.
For warranty repair information, call 1-800-332-4094.
8
Noise Emission.
Notes concerning noise emission:
Given that there exists a relationship between noise level and exposure times, it is not
possible to precisely determine the need for supplementary precautions. The factors
affecting the true level of exposure to operators are clearly the amount of time exposed and
the characteristics of the working environment, such as other sources of dust and noise, etc.,
for example, adjacent machines - in other words, the level of ambient noise. It is possible that
exposure level limits will vary from country to country.
9
Motor
Induction,1725RPM, 3 HP 220V
Voltage
220v 60hz single phase input, 3 phase output
Recommended
breaker size
15 amp
Swing over bed
24" (609mm)
Swing over banjo
19.75" (501mm)
Outboard swing
max
38" (965mm)
Distance between
centers
36" (914mm)
Floor to spindle
center
44.5"(1130mm)
Floor to bed height
32.5" with pads (826mm)
Floor space
W60" D26" H52.25"(1524mm, 660mm, 1327mm)
Tool rest
12" (305mm)
Speed range high
135 - 3500 RPM
Speed range low
50 - 1300 RPM
VFD
DeltaS1 variable frequency drive
Drive belt
Poly-groove drive belt with easy access
Spindle
1.25" x 8 tpi right hand thread
Spindle taper
MT 2
Spindle lock
Spring loaded
Spindle index
14 / 36 / 48 positions with lock
Headstock &
tailstock bore
0.375" dia (9.5mm dia)
Tail stock travel
4.5" (114mm)
Tail stock removal
Self- ejecting
Tailstock tapers
MT 2
Face plate
3" diameter (76mm)
Bed material
Steel
Weight (Net / ship)
532/560 lbs (242kg / 255 kg)
Specification sheet.
10
Receiving your machine.
Note. It is probable that your machine will be delivered by a third party. Before you unpack
your new machine you will need to first inspect the packing, invoice and shipping documents
supplied by the driver.
Insure that there is no visible damage to the packing or the machine. You need to do this prior
to the driver leaving. All damage must be noted on the delivery documents and signed by you
and the delivery driver. You must then contact the seller (Laguna Tools) as soon as practical.
If damage is found after delivery, contact the seller as soon as is practical.
Note. It is probable that you will find sawdust within your machine. This is because the
machine has been tested prior to shipment from the factory and or Laguna Tools.
Laguna Tools endeavours to test machines prior to shipping to customers. As movement can
take place during transportation it must be noted that additional machine movement can take
place between Laguna Tools and the end user and some adjustments may have to be
undertaken by the customer. These adjustments are covered in the various sections of this
manual.
11
Introduction to lathes.
This machine is designed to give you years of safe service. Read this owner's manual in its
entirety before assembly or use.
Parts of the lathe.
The lathe consists of a number of major parts, which are discussed in this manual. Take the
time to read this section and become familiar with the machine.
Head stock Tool rest Tail stock Drive &live center storage
Tool storage Leg Bed Banjo Adjustable feet Leg
12
Underside of lathe bed
Identification.
There is a plate at the back of the machine listing all the
manufacturing data, including the serial number, model,
etc.
Lathe Bed.
The bed is a machined heavy steel welded construction.
13
Legs with adjustable feet assembled
Lathe legs.
The Legs are cast iron, and their heavy construction gives the machine a low center of gravity
and ensures that it is very stable. The legs are supplied with adjustable feet to allow the
machine to be leveled.
Head stock.
The head stock is cast iron and houses the variable speed control and motor. The
Spindle can be locked in 14 / 36 and 48 positions.
14
Headstock removed from the
bed
Head or remote selection
switch
Tailstock viewed from the back
Tailstock viewed from the front
Tail stock.
The tail stock is of cast iron construction, and the spindle has a travel of 4 1/2 in. It can
accommodate centers and other tools which have a number 2 Morse Taper. The tail stock can
be moved to any position on the lathe bed and locked to suit the job at hand.
Tool rest.
The tool rest can be moved to any position on the lathe bed and locked to suit the job at hand.
The tool rest has a tall profile to allow the bowl turner to turn steep angles. The leading edge
is made from 6mm hardened steel.
15
Tool rest assembled to the bed
Tool rest
VFD with cover open
Power sockets
Electrical system.
220V: The electrical control system (VFD) is housed at the back of the head stock, The VFD
converts single phase 220v to three phase. There is a speed readout at the front of the lathe
with controls to fine adjust the RPM of the spindle. . A power cord with 220V plug is provided.
There are two electrical sockets to the side of the VFD..
16
Tool storage bracket
Tool storage.
A tool storage bracket which can be mounted on either leg.
What you will receive with the lathe.
17
Head stock Tool rest Tail stock Drive &live center storage
Tool storage Leg Bed Banjo Adjustable feet Leg
Remote controller
Face plate Tool rack Rotating center Adjustable feet Tail stock bracket
18
Loading...