Labnet 611D User Manual

HIGH PERFORMANCE INCUBATORS
M
I
ODELS: 311D, 611D
TABLE OF CONTENTS
SECTION 2.0 WARRANTY SECTION 3.0 SPECIFICATIONS
SECTION SECTION SECTION 6.0 CONTROLS OVERVIEW SECTION 7.0 OPERATION SECTION 8.0 CLEANING AND ROUTINE CARE SECTION 9.0 SERVICE AND TROUBLESHOOTING SECTION 10.0 PARTS LIST WIRE DIAGRAM
4861281
These units are high performance incubators for professional, industrial or educational use where the preparation or testing of materials is done at approximately atmospheric pressure and no flammable, volatile or combustible materials are being heated. These units are not intended for hazardous or household locations or use.
SECTION 1.0 INTRODUCTION
4.0 RECEIVING AND INSPECTION
5.0 INSTALLATION
REV. 3/2005
2
Section
INTRODUCTION
The Labnet Incubators have been designed for general purpose incubations (<65ºC), as well as those applications requiring higher temperatures (up to 65ºC).
Temperature within the incubator is controlled and regulated by a microprocessor. Temperature is set and displayed digitally. An independent, user settable safety thermostat protects samples and the incubator from overheating in the unlikely event of a primary controller failure.
A fan, located in the chamber, assists in providing an exceptionally uniform environment. The fan also speeds temperature recovery after the door of the incubator has been opened. For applications where the flow of air in the chamber is undesirable, the fan may be switched off.
The interiors of the 311D and 611D incubators are constructed of stainless steel. The exteriors are made of cold rolled steel to resist corrosion and provide strength. The door of the incubator consists of two parts. The inner door is glass to allow for viewing the chamber contents without disrupting the temperature environment. The outer door is solid and insulated. It is also heated to help in maintaining the chamber temperature. The heated door prevents condensation from forming on the inner glass viewing door.
Your satisfaction and safety require a complete understanding of this unit. Read this instruction manual thoroughly before attempting to operate the incubator. All operators should be given adequate training before using this incubator. Note that any alterations or modifications to the incubator may void the warranty.
Should any questions arise concerning the Labnet Incubators, please call Labnet International’s Customer Service Department at 888 522-6381, Monday through Friday, 8:30am to 5:00pm, EST.
3
Section
WARRANTY
Labnet International, Inc. guarantees that the Model 311/611 Incubator that you have received meets its published specification. The incubator is guaranteed to be free of defects in materials and workmanship for a period of one year from the date of purchase. This guarantee is valid only if the unit has been used in accordance with the instructions in this manual and for its intended purpose. Labnet International, Inc. shall not be responsible for consequential damages or damages resulting from the abuse or misuse of this equipment. Labnet International’s liability shall be limited to the repair or replacement of the unit or refund of the purchase price, at Labnet International’s discretion.
For technical service, contact Labnet International’s Service Department at 888 522-6381. Labnet International, Inc. reserves the right to alter the specification of the incubator without
notice. This allows the incorporation of improvements as they are developed. Please fill in the following information. This information will be required in the event that
service becomes necessary. The serial number is found on the data plate located on the back of the unit.
Serial number _______________________ Date of purchase _____________________
4
Section
SPECIFICATIONS
Temperature Range Ambient +5 to 95C Temperature Uniformity
311D +0.2 @ 37C
611D +0.25 @ 37C Temperature Accuracy +0.2 Temperature Set / Display Digital / digital Temperature Control Microprocessor Overtemperature Safety Independent, settable Interior Outlet 1AMP Door Inner – glass Outer - solid, heated Chamber Volume
311D 2.75 cu ft
611D 6.0 cu ft Exterior Construction Cold rolled steel Interior Construction Stainless steel Exterior Dimensions
311D 27W x 20D x 29"H
611D 31W x 26D x 34"H Interior Dimensions
311D 17W x 14D x 20"H
611D 21W x 20D x 25"H Standard Accessories Adjustable leveling feet 2 Steel Shelves Shelving Points Voltage Requirements 120V / 60Hz Power / Current
311D 800W/6.7A
611D 850W/7.1A
5
Section
RECEIVING AND INSPECTION
4.1 Inspection: The carrier, when accepting shipment, also accepts responsibility
for safe delivery and is liable for loss or damage. On delivery, inspect for visible exterior damage, note and describe on the freight bill any damage found, and enter your claim on the form supplied by the carrier.
4.2 Inspect for concealed loss or damage on the unit itself, both interior and exterior.
If any, the carrier will arrange for official inspection to substantiate your claim.
4.3 Return Shipment: Save the shipping crate until you are sure all is well. If for any
reason you must return the unit, contact Labnet International, Inc. for authorization and supply the data plate information.
4.4 Accessories: Verify that all of the equipment indicated on the packing slip is
included with the unit. Carefully check all packaging before discarding. This unit is equipped with 2 large shelves, 8 shelf clips and 4 leveling feet. If any of these items is missing, contact Labnet International’s Customer Service Department immediately.
6
Loading...
+ 12 hidden pages