KYORITSU KEW 3128 User Manual

Driver Installation Manual for "KEW Windows for KEW3128"

This manual contains explanations how to install the special
application and the USB driver on Windows 8 PCs.

1. Inst alla tion of KEW Window s for KEW3128

 (1) The following should be checked before installing this

application.

  ･ To prepare your system for installation, please close

all open programs.

  ･ Be sure NOT to connect the instrument with the USB

until installation completes.

･ Installation shall be done with Administrator right.
  ･ To use KEW Windows for KEW3128, .NET Framework

3.5 is required.

    If .NET Framework 3.5 is not installed in your PC, it

will be automatically installed when installing this
application.

    An internet connection is required to install .NET

Framework 3.5.

 (2) Inser t the CD -ROM in your PC's CD drive. Then

following pop-up will appear at the upper right on the
screen. Left-click on this box.

 (3) Click and select "Run KEWLauncher.exe" when the

following box appears.

   If User Account Control dialog box appears, click "Yes".

 (4) When the following window appears, click "Nex t".

 (5) Read through and understand the License Agreement

and click "I accept….", and then click" Next".

 (6) Click "Next" after entering the user information and

other supplementary information.

 (7) Confirm the information on installation, and then click"

Install" to start an installation.

   The following box will appear if .NET Framework3.5 is

not installed in your PC.

   If a message requiring restarting your PC is displayed,

click "Yes" and restart your PC.

   Run "KEWSetupLauncher.exe" from the CD after

restarting the PC.

 (8) Click "Finish" when "InstallShield Wizard Complete"

dialog box appears.

 (9) When the installation wizard completes, subsequent

installation initiates automatically.

   Click "Next".

 (10) Read through and understand the License Agreement

and click I accept…., and then click" Next".

 (11) Click "Next" after entering the user information and

other supplementary information.

 (12) Confirm the information on installation, and then click"

Install" to start an installation.

 (13) Click "Finish" when "InstallShield Wizard Complete"

dialog box appears.

   If neither (2) nor (3) appears, run "KEWLauncher.exe"

from the CD.

2. Ins tall ation of USB Driver

 (1) Connect MODEL8212 and your PC with the USB cable

supplied with the instrument.

   When the following window appears, install the driver

according to the following procedure.

(2) Click "Control Panel" -> "Device Manager".

 (3) Cl i c k Other devicesand then right-click on

MODEL8212.

   Then clickUpdate Driver Software.

 (4) Select  Browse my computer for driver software".

 (5) Check the box forInclude subfolders, and then

clickBrowse.

 (6) Select the disk drive in which the CD resides and click

OK.

   If the CD is not inserted, close the window once by

clicking "Cancel" and select again after inserting the CD.

 (7) When the following confirmation message appears,

after clickingNext, clickInstall.

   Select "Install this driver software anyway" if the

following warning window appears. (There is no problem
to continue installing because operation has already
been verified.)

 (8) Install is completed when the wizard says "Windows has

successfully updated your driver software".

   Click "Close".

 (9) ClickOther devicesunder the Device Manager, and

then right-click on USB Serial Port.

  Then clickUpdate Driver Software.

 (10) Repeat above step (3) through (6). Installation is

completed when the wizard says Windows has
successfully updated your driver software. Click

Close.

 (11) The following t wo icons will appear in the Device

Manager when the driver is successfully installed.

USB Driver Un-installation

When the installation of the USB driver is interrupted and
re-installation cannot be done, follow the
procedure below and delete the existing driver, and then
install it again.

(1) Connect your PC and the instrument with the USB cord.
 (2) Click theControl Panelin the Start menu.
 (3) ClickDevice Managerin the Control panel.
 (4) Right click onMODEL8212 USBunder"Other devices".
 (5) ClickUninstallto uninstall the USB driver.

 (6) Remove the USB cord connecting your PC and the

instrument once, and connect them again.

 (7) WhenFound New Hardware Wizardwindow appears,

follow the procedures described inUSB Driver
Installationand install the driver.

92-2203