Page 1
Page 2
ii 82-G1651-1EN, Rev. 002
FCC Notice:
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Caution:
The user is cautioned that changes or modifications
not expressly approved by the party responsible for
compliance could void the warranty and users’
authority to operate the equipment.
Note:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
FCC Radiation Exposure Statement:
To comply with the FCC RF exposure compliance
requirements, this device must not be co-located or
operating in conjunction with any other antenna or
transmitter.
Industry Canada Notice
Operation is subject to the following two conditions:(1)
this device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation of the
device. The term “IC:” before the radio certification
number only signifies that Industry Canada technical
specifications were met. This product meets the
applicable Industry Canada technical specifications of
the RSS210.
Kyocera is a registered trademark of Kyocera
Corporation. The Bluetooth word mark and logos are
owned by the Bluetooth SIG, Inc. and any use of such
marks by Kyocera Wireless Corp. is under license. All
other marks are held by their respective owners.
Copyright © 2007 Kyocera Wireless Corp.
All rights reserved.
Page 3
Wireless Portable Speaker with Headset iii
CONTENTS
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Charging the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
The Wireless Portable Speaker with Headset can be charged three different ways: . . . . . . . . . . . . . . . 4
Charging the headset using the speaker base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Multi-function button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Turning the device on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Volume adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pairing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Placement of the device in the car . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Making a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Answering a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Ending a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rejecting an incoming call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Call transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Switching from speaker to headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Three-way calling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Page 4
Page 5
Wireless Portable Speaker with Headset 1
WIRELESS PORTABLE SPEAKER
WITH HEADSET
Introduction
Congratulations on your purchase of the Wireless
Portable Speaker with Headset featuring
Bluetooth® wireless technology. The headset is
comfortable to wear and easy to use.
Bluetooth wireless technology
Bluetooth wireless technology is a short-distance
wireless communication technology. The range of
operation between Bluetooth wireless technology
devices is about 10M (33 ft.). Bluetooth wireless
technology does not require line of sight and can
transmit through walls and other non-metal
obstacles. Thick or reinforced concrete can limit
the range.
The Wireless Portable Speaker with Headset
complies with Bluetooth wireless technology version
1.2 and supports both the Headset Profile and
Hands-free Profile. The Wireless Portable Speaker
with Headset has an innovative structural and
functional design that allows it to be used as either
a car kit/speaker or a headset according to the
user's needs.
Package contents
Note: Please refer to actual product. The above
pictures are only for your reference.
Page 6
2 82-G1651-1EN, Rev. 002
Getting to know your Wireless Portable Speaker with Headset
Refer to the following illustration to identify the parts
1
Multi Function turns the wireless portable speaker and/or headset on/
off, answers calls, ends calls. Its functionality depends on how long
you keep the button pressed:
A
short press is less than one second
A
long press is two to five seconds
2
Volume + increase
3
Volume - decrease
4
Mute the microphone during conversation, and the other side won't
hear your voice
5
Charging jack for AC adapter
6
Microphone transfers sound into electronic signal
7
Receiver transfers electronic signal into sound
8
Charging indicator indicates charging status
9
Working indicator indicates working status
Speaker Base
Headset
Page 7
Wireless Portable Speaker with Headset 3
Charging the battery
Your Wireless Portable Speaker with Headset needs to be charged before initial use and recharged when the
red light blinks at intervals when you power it on.
Important: The rechargeable battery in the Wireless Portable Speaker with Headset must be disposed or
recycled according to local ordinance regulations.
Page 8
4 82-G1651-1EN, Rev. 002
The Wireless Portable Speaker with Headset can be charged three
different ways:
Charging with the home
power adapter
1. Connect the USB cable to the AC Adapter.
2. Insert the other end of the USB cable into the
speaker’s power jack.
3. Plug the AC Adapter into an appropriate
electrical outlet (or power socket).
4. The charging indicator will light up, indicating
that the Wireless Portable Speaker with Headset
is connected to a power source, and is charging.
5. When charging is completed, the indicator light
will turn off.
6. Remove the AC Adaptor from the outlet.
Charging with your PC
1. Connect one end of the USB cable to your PC or
any other equipment supplying USB power.
2. Insert the other end of the USB cable into the
speaker’s power jack. The charging indicator
will light up, indicating that the Wireless
Portable Speaker with Headset is connected to
a power source.
3. When charging is completed, the indicator light
will turn off. Remove the USB cable from the PC,
or other equipment.
Charging with the car adapter
1. Connect the car adapter to one end of the
USB cable.
2. Insert another end of the USB cable into the
speaker’s power jack.
3. Plug the car adapter into the 12 volt power
source jack. The charging indicator will light up,
indicating that the Wireless Portable Speaker
with Headset is connected to a power source.
4. When charging is completed, the red light will
turn off.
5. Remove the car charger from the 12 volt power
source jack.
Charging the headset using the
speaker base
Note: The speaker base must first be charged for at
least 5 minutes. (Charging for the entire unit
may take up to 4 hours).
1. Insert the headset into the speaker base. The
indicator on the headset will light up (indicating
that it is charging).
2. When charging is completed, the red light will
light will turn off.
3. Remove the headset from the speaker base. It is
now ready for use.
Note: You can use your headset while it
is charging.
Page 9
Wireless Portable Speaker with Headset 5
Battery use and standby times
Headset
Standby time is up to 100 hours.
Talk time is up to 4 hours.
Charging time is around 2.5 hours.
Whole unit (headset & speaker base)
Standby time is up to 200 hours.
Talk time is up to 6 hours.
Charging time is around 4 hours
Note: If the headset and speaker base both need to
be recharged, charge the base for five
minutes prior to charging both.
Multi-function button
The function of depends on how long you
keep the button pressed.
• A short-press is less than one second
• A long-press is two to five seconds
Turning the device on and off
Tur n o n
Long press until blue light blinks and the
Wireless Portable Speaker beeps once, then release
the button. The power is on.
The mobile device will ask if you would like to
connect to the Wireless Portable Speaker with
Headset. Confirm the connection.
Tur n o ff
Long press until red light blinks quickly, and
the device beeps once, then release the button. The
power is off.
The mobile device will disconnect from the Wireless
Portable Speaker with Headset.
Volume adjustment
During a call, you can adjust the volume using
and/or .
1. Press to increase volume.
2. Press to decrease volume.
Notes:
•
There will be a low, short sound each time
you press or ; the volume of this
tone will increase or decrease as you press
the buttons.
• Please set your speaker to a suitable volume
between maximum and minimum.
• You can also use the volume buttons of
your mobile phone to adjust the volume of
the speaker.
Pairing
Pairing is the process of linking the Wireless
Portable Speaker with Headset with your Bluetooth
wireless technology enabled mobile phone.
Before you use the speaker with your mobile phone,
the devices must be paired.
After pairing is complete, the speaker can only be
used with the mobile phone with which it was
paired. If you wish to use the speaker with a
different mobile phone, you must repeat the pairing
process with the new mobile phone. When you do
this, the speaker will no longer work with the
previous mobile phone.
Page 10
6 82-G1651-1EN, Rev. 002
Begin the pairing procedure with the speaker
powered off.
1. Press for 5 seconds the until the speaker
beeps twice and the red and blue lights blink
alternately. This indicates that your speaker is in
pairing status.
Note: You will find that the blue light will blink first
before the red and blue lights blink
alternately, which indicates the power is
on. Make sure to continue pressing
until the lights are blinking alternately and
the speaker beeps three times.
2. Execute the search function on your mobile
phone to search for the Bluetooth wireless
technology device. The search may take
several seconds
3. After the search process has been completed
successfully, the mobile phone screen will
display the name(s) of the device(s) found.
4. Select GCK800 and acknowledge that you
would like to pair the device.
5. You will be requested to enter a password,
passkey, or identification code. Enter “0000”,
and then confirm. Now, your mobile phone
starts pairing with the speaker.
6. When pairing has been successfully completed,
only the blue light blinks, instead of the red and
blue that were previously blinking
Notes:
•
Confirm that your Wireless Portable Speaker
with Headset is in paring status before pairing,
otherwise your mobile phone will not find it.
• If pairing is unsuccessful after about one
minute, the speaker will automatically revert
to standby mode.
• Pairing guarantees secure communication. The
Identification Code exchange will assure that
there is an exclusive connection between your
mobile phone and the speaker.
• Once your mobile phone and speaker have been
paired, you will not need to pair it again unless
you remove it from your mobile phone.
Connecting
Once you have successfully paired your mobile
phone with the GCK800, you will need to connect
the two devices in order to use them together.
The mobile phone will ask if you would like to
connect the device.
On the mobile phone, confirm that you want to
connect to the device.
You are now ready to use the speaker.
Disconnecting
The speaker will automatically disconnect from your
mobile phone if you are too far from the mobile
phone or if you power off either device.
Reconnecting
If your speaker is disconnected from your mobile
phone, simply press and hold the , or
until the mobile phone acknowledges it. Your
mobile phone will ask if you would like to connect
to the speaker. Answer
Yes to connect.
Page 11
Wireless Portable Speaker with Headset 7
Placement of the device in the car
To maximize users' operating flexibility, the Wireless
Portable Speaker with Headset has been designed
to be located inside a car in a number of ways. Two
placement suggestions are:
• Insert the Wireless Portable Speaker with
Headset into the metal clamp and clip onto
the sun visor.
- or -
• Peel the paper from the back of the Wireless
Portable Speaker with Headset’s “Back-Stick
Accessory” and stick it onto a smooth, flat
surface in the car.
Notes:
•
Place the Wireless Portable Speaker with
Headset in a position that will not block
the driver's sight or interfere with safe
vehicle operation.
• The user should ensure the position of the
Wireless Portable Speaker with Headset inside a
car complies with international, state, and local
regulations.
• Ensure the position of the Wireless Portable
Speaker with Headset won't interfere with any
safety equipment in a car, such as an air bag.
• The Wireless Portable Speaker with Headset
should be placed in a safe position where it will
not dislodge and harm the passengers when the
auto encounters bumps, collisions, or other
accidents while driving.
Making a call
Make sure your the speaker is connected to your
mobile phone before you make a call. The speaker
can support “voice dialing” function if your mobile
phone has this function. For details on voice-dialing,
please refer to your mobile phone's user manual.
Voice dialing
Note: The phone must support hands-free and
voice recognition functions and voice dial
must already be set up for this number.
1. Press for approximately two seconds.
The mobile phone asks you to say a name.
2. Press to cancel during voice dialing.
The phone beeps and ends the call.
Note: It is a good idea to use your speaker to
record your dialing voice.
Dial with mobile phone keypad
Dial numbers in the normal way. You may need to
transfer the call from your phone to the headset.
Otherwise, you will hear through the speaker when
the call is connected.
Page 12
8 82-G1651-1EN, Rev. 002
Re-dial the last dialed number
• In standby mode, press for two to five
seconds until the speaker beeps.
Note: Your mobile phone's model and settings
determine whether there is a keypad tone or
not. Adjust the volume during your call with
and .
Answering a call
Before using the speaker to answer an incoming
call, make sure that the speaker is connected to
your mobile phone or that your mobile phone has
stored the pairing information of the speaker and
these two devices are within effective distance
(approximately 10 M or 33 ft.).
• When there is an incoming call, the ring tone is
heard from both the speaker and your mobile
phone. Press to answer the phone.
• If “automatic answer” function is set on
your mobile phone, the speaker will
automatically answer the call without
pressing on the headset.
• If the speaker is off when there is an incoming
call, a two- to five-second press of will turn
it on, and then press it for less than one second
to answer the call.
Notes:
•
Some brands of mobile phones don't ring,
instead, the speaker rings when there is an
incoming call. Simply press to answer
the call.
• Some brands of mobile phones ring, but the
speaker doesn't ring when there is an incoming
call. Press to answer the call when the
mobile phone rings.
Ending a call
When using the speaker, you can end a call in any
of these ways:
• Short press
• Press the end call button on your mobile phone
• The call will end automatically when the party
with whom you're talking ends the call
Mute
• In call mode, press and hold the until you
hear a tone. The microphone will be in mute
mode, and the other party cannot hear you.
While you have your phone muted, you may
hear tones at regular intervals.
• In mute mode, press the to return to
normal mode.
Note: When using the headset alone, you may
achieve this function by pressing the
and on the headset at the same time.
Rejecting an incoming call
When using the speaker, you can reject a call in any
of these ways:
• Long press
• Press the end call button on your mobile phone
Page 13
Wireless Portable Speaker with Headset 9
Call transfer
Transfer the call from the speaker to
your mobile phone
During a call, you may switch from the speaker to
your mobile phone in any of these ways:
• Press for two to five seconds until you
hear it beep twice
• Transfer the call using your mobile phone’s
functionality
• Turn the speaker off
Transfer the call from the speaker to
your mobile phone
During a call, you may switch the call from the
mobile phone back to the speaker
• Press for two to five seconds until it
beeps twice
• Transfer the call using your mobile
phone’s functionality
• If the speaker is turned off during a call, turn it
on and short press to transfer the call from
the mobile phone to the speaker.
Note: These procedures will vary according to
the functionality of the mobile phone you
are using.
Switching from speaker
to headset
If you need to switch from a speaker phone call to a
more private headset call, simply grasp the headset,
pull it out of the base unit and insert the earpiece
into your ear. The call is automatically switched to
the headset only. Sounds will no longer be emitted
from the base unit. To return the call to speaker,
remove the headset from your ear and replace it
into the base unit.
Three-way calling
If your mobile phone and the mobile service you
subscribe to support three-way calling, you can also
use this function with the speaker.
Follow procedures below when one party is on
the line with you and the other is attempting to
call you:
• To continue on the active call and answer the
waiting call:
short press .
• To hang up the active call and answer the
waiting call:
press for two to five seconds
until it beeps twice.
• To start the three-way call function: press
for two to five seconds until it beeps twice.
• To end the three-way call function:
press for two to five seconds during
three-way call.
Important information
Maintenance
• Keep this product in a dry place, and clean it
periodically with a soft cloth.
• Do not store in a dusty place, nor in very high
nor low temperatures.
• Do not disassemble this product, as this may
damage it.
• Avoid rough treatment such as dropping,
knocking, or shaking this product.
• Be sure to plug the adapter only into an
appropriate electrical outlet to avoid damaging
the battery.
Page 14
10 82-G1651-1EN, Rev. 002
Battery
• When using the Wireless Portable Speaker with
Headset for the first time, make sure the battery
has been fully charged for at least 3 hours.
• Battery maintenance: The battery can only be
replaced by a professional. If this product will
not be used for a long time, make sure to
charge it at least once every two months.
Caution: Do NOT dispose of batteries in fire
because there is a danger of explosion.
Power Supply
• An alternative power adapter can only connect
with a compatible power source.
• Hold the adapter, not the cable, when you
remove the adapter from power socket.
• Do NOT directly spray liquid or cleansers on the
surface of your the Wireless Portable Speaker
with Headset. Spray the cleanser on the soft
cloth, and then clean the device with it.
Disconnect the charger and turn off the device
when you clean it.
Cars with air bags
Caution: Do NOT place the Wireless Portable
Speaker with Headset on top of an air bag or within
the area an air bag can reach when it is deployed. If
you place the Wireless Portable Speaker with
Headset within an air bag’s deployment range, it
may be ejected and may result in serious harm to
the driver or passengers.
Frequently Asked Questions
1. Can the Wireless Portable Speaker with Headset
be used for all brands of mobile phones?
– Yes, as long as the mobile phone has built-in
Bluetooth Voice Gateway functionality.
2. How far is the effective distance between the
Wireless Portable Speaker with Headset and a
Bluetooth wireless technology enabled
mobile phone?
– The effective distance (with no barriers) is 10
meters (33 feet, Class II).
3. Can another wireless mobile phone user hear
my conversation?
– No. Through pairing, you have created a
secure link between your mobile phone and
your GCK800.
4. Why does the red light turn on and flash?
– The battery of your Wireless Portable
Speaker with Headset is running low and
needs to be recharged.
5. Why is my mobile phone unable to find the
Wireless Portable Speaker with Headset?
– Your mobile phone should be able to find
the Wireless Portable Speaker with Headset
when it is in pairing mode. Refer to
“Pairing” on page 5 for details.
6. Is pairing needed each time when I use the
Wireless Portable Speaker with Headset?
– No. The pairing information is stored in both
devices even if one or both of them have
been turned off.
Page 15
Wireless Portable Speaker with Headset 11
7.
Is it necessary to reconnect the two devices
when there is an interruption on the link
between my mobile phone and the Wireless
Portable Speaker with Headset?
– It varies according different brands of mobile
phones. Some mobile phones can be
reconnected automatically if both devices
are within the effective distance. Some
mobile phones must be reconnected.
8. Why is there noise in my Wireless Portable
Speaker with Headset?
– When the distance between your mobile
phone and the Wireless Portable Speaker
with Headset exceeds the effective distance,
background noise will occur accordingly.
– If the signal for your mobile phone is poor in
your area, the Wireless Portable Speaker
with Headset will also receive poor quality
reception.
9. What should I do if the Wireless Portable
Speaker with Headset's sound quality is poor?
– Try adjusting the volume of your mobile
phone or Wireless Portable Speaker with
Headset. Also, check the quality of the signal
on your mobile phone in your area.
Other instructions
Different Bluetooth wireless technology enabled
mobile phones may have been designed in different
ways, thus may function differently. The instructions
provided in this user guide may not cover all
information. For further information please refer to
your mobile phone user guide.
Page 16
12 82-G1651-1EN, Rev. 002
Kyocera Wireless Corp. (“KYOCERA”) offers you a
limited warranty that the enclosed product or
products (the “Product”) will be free from defects in
material and workmanship for a period that expires
one year from the date of sale of the Product to
you, provided that you are the original end-user
purchaser of the Product and provided that your
purchase was made from an authorized supplier.
Transfer or resale of a Product will automatically
terminate warranty coverage with respect to that
Product. This limited warranty is not transferable to
any third party, including but not limited to any
subsequent purchaser or owner of the Product. This
limited warranty is applicable only to end users in
the United States and Canada.
KYOCERA shall, at its sole and absolute discretion,
either repair or replace a Product (which unit may
use refurbished parts of similar quality and
functionality) if found by KYOCERA to be defective
in material or workmanship, or if KYOCERA
determines that it is unable to repair or replace such
Product, KYOCERA shall refund the purchase price
for such Product, provided that the subject Product
(i) is returned, with transportation prepaid, to a
KYOCERA authorized service center within the one
year warranty period, and (ii) is accompanied by a
proof of purchase in the form of a bill of sale or
receipted invoice which evidences that the subject
Product is within the one year warranty period
(“Proof of Purchase”). After the one year
warranty period, you must pay all shipping, parts
and labor charges.
This limited warranty does not cover and is void
with respect to the following: (i) any Product which
has been improperly installed, repaired, maintained
or modified; (ii) any Product which has been
subjected to misuse (including any Product used in
conjunction with hardware electrically or
mechanically incompatible or used with accessories
not approved by KYOCERA), abuse, accident,
physical damage, abnormal operation, improper
handling, neglect, exposure to fire, water or
excessive moisture or dampness or extreme changes
in climate or temperature; (iii) any Product operated
outside published maximum ratings; (iv) cosmetic
damage; (v) any Product on which warranty stickers
or Product serial numbers have been removed,
altered, or rendered illegible; (vi) cost of installation,
removal or reinstallation; (vii) signal reception
problems (unless caused by defects in material and
workmanship); (viii) damage the result of fire, flood,
acts of God or other acts which are not the fault of
KYOCERA and which the Product is not specified to
tolerate, including damage caused by mishandling,
shipping and blown fuses; (ix) consumables (such as
fuses); or (x) any Product which has been opened,
repaired, modified or altered by anyone other than
KYOCERA or a KYOCERA authorized service center.
USE ONLY KYOCERA APPROVED ACCESSORIES
WITH KYOCERA PHONES. USE OF ANY
UNAUTHORIZED ACCESSORIES MAY BE
DANGEROUS AND WILL INVALIDATE THE PHONE
WARRANTY IF SAID ACCESSORIES CAUSE
DAMAGE OR A DEFECT TO THE PHONE.
CONSUMER LIMITED WARRANTY
Page 17
Wireless Portable Speaker with Headset 13
KYOCERA SPECIFICALLY DISCLAIMS LIABILITY FOR
ANY AND ALL DIRECT, INDIRECT, SPECIAL,
GENERAL, PUNITIVE, EXEMPLARY, AGGRAVATED,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN
IF ADVISED OF THE POSSIBILITY THEREOF,
WHETHER FORESEEABLE OR UNFORESEEABLE OF
ANY KIND WHATSOEVER, INCLUDING BUT NOT
LIMITED TO LOSS OF PROFITS, UNANTICIPATED
BENEFITS OR REVENUE, ANTICIPATED PROFITS
ARISING OUT OF USE OF OR INABILITY TO USE ANY
PRODUCT (FOR EXAMPLE, WASTED AIRTIME
CHARGES DUE TO THE MALFUNCTION OF A
PRODUCT) OR CONTRIBUTION OR INDEMNITY IN
RESPECT OF ANY CLAIM RELATED TO A PRODUCT.
REPAIR OR REPLACEMENT OF A DEFECTIVE
PRODUCT OR REFUND OF THE PURCHASE PRICE
RELATING TO A DEFECTIVE PRODUCT, AS
PROVIDED UNDER THIS WARRANTY, ARE YOUR
SOLE AND EXCLUSIVE REMEDIES FOR BREACH OF
THE LIMITED WARRANTY, AND SUBJECT TO THIS
WARRANTY, THE PRODUCTS ARE APPROVED AND
ACCEPTED BY YOU “AS IS”. KYOCERA MAKES NO
OTHER WARRANTIES, REPRESENTATIONS OR
CONDITIONS OF ANY KIND, ORAL OR VERBAL,
EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE,
WITH RESPECT TO THE PRODUCTS, INCLUDING
BUT NOT LIMITED TO ANY IMPLIED WARRANTY OR
CONDITION OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE OR AGAINST
INFRINGEMENT OR ANY IMPLIED WARRANTY OR
CONDITION ARISING OUT OF TRADE USAGE OR
OUT OF A COURSE OF DEALING OR COURSE OF
PERFORMANCE. NO DEALER, DISTRIBUTOR, AGENT
OR EMPLOYEE IS AUTHORIZED TO MAKE ANY
MODIFICATION OR ADDITION TO THIS WARRANTY.
Some jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages,
or allow limitations on how long an implied
warranty lasts, so the above limitations or
exclusions may not apply to you. This limited
warranty gives you specific legal rights, and you
may also have other rights which vary from
jurisdiction to jurisdiction.
For warranty service information, please call the
following telephone number from anywhere in the
continental United States and Canada:
1-800-349-4478 or 858-882-1401; or contact
KYOCERA at the following address:
10300 Campus Point Drive, San Diego, California,
92121-1582, USA, Attention: Technical Support.
DO NOT RETURN YOUR PRODUCTS TO THE
ABOVE ADDRESS.
Please call or write for the
location of the Kyocera Wireless Corp. authorized
service center nearest you and for procedures for
obtaining warranty service.
Loading...