Kussmaul 091-155 User Manual

SAFETY LOCK 3

AUTOMATIC SAFETY LOCK, 3 OUTPUTS

A CONTROLLER WHICH PERMITS
UNA TTENDED ENGINE OPERATION
BUT PREVENTS UNAUTHORIZED
USE OF THE VEHICLE

SIMPLE INSTALLATION

PERMITS ENGINE
TO RUN WITH THE
IGNITION KEY REMOVED

ENGINE STOPS AND CANNOT BE
REST AR TED IF A TTEMPT IS MADE
TO DRIVE AW AY

This simple, low cost controller bypasses the ignition
switch when activated by the closure of a momentary
switch. The operator may then remove the ignition key
without shutting the engine down. Movement of the ve­hicle is prohibited by interlocking the SAFETY LOCK with
a switch operated by the foot brake, a neutral safety switch
on the gearshift or a parking brake operated switch. Oper­ating any one of these will cause the relays in the SAFETY
LOCK to drop out and interrupt the ignition circuit to stop
the engine. The authorized operator need only insert the
key and turn on the ignition to operate the vehicle. With
the key in the lock and turned on, the ignition circuit is
completed as normal and the opening of the SAFETY
LOCK relays has no eff ect on engine operation. This unit
is for vehicles that require 3 independent relays for the
vehicles ignition.

SPECIFICA TIONS:
Volts: 12 volts, D.C.
Relay Contacts: Normally Open, 30 Amps.
Weight: 6 ounces
Enclosure: unsealed

MODEL #091-155-12

3/16" DIA.

3.75

2.00

3.50

OUTLINE DRAWING

4.25

1.625

KUSSMAUL ELECTRONICS COMPANY, INC.

170 CHERRY AVE., WEST SAYVILLE, NY 11796

TELEPHONE in NY: 631-567-0314 TOLL FREE: 800-346-0857 FAX: [phone] e-mail: [e-mail] in NY: 631-567-0314 TOLL FREE: 800-346-0857 FAX: [phone] e-mail: [e-mail]

TELEPHONE in NY: 631-567-0314 TOLL FREE: 800-346-0857 FAX: [phone] e-mail: [e-mail]

TELEPHONE in NY: 631-567-0314 TOLL FREE: 800-346-0857 FAX: [phone] e-mail: [e-mail] in NY: 631-567-0314 TOLL FREE: 800-346-0857 FAX: [phone] e-mail: [e-mail]

+12 volt
Power

The common terminal of Relay K1

must be connected to the +12 volt

power for the unit to operate

IGNITION SWITCH

To Ignition
System

Brake
Light
Switch

Brake
Light

Output #3

Output #2

+12 V

This line resets

K3

K2

N.C.
N.O.

COM.

N.C.

COM.

N.O.

12345

N.C.
N.O.

o

t

a

c

i

d

o

n

p

I

e

a

D

v

t

r

s

e

n

i

s

n

e

h

K1

COM.

SET

PUSHBUTTON

E

L

b

O

W

S1

(bypasses ignition)

Indicator illuminates when ignition
switch is bypassed

NOTE:

accessories when SAFETY LOCK 3 is activated

Output 2 and Output 3 provide +12 volts to

(OPTIONAL)

r

y

t

i

r

a

l

g

n

i

l

l

INSTALLATION:

1.

Mount unit in a suitab le location protected from moisture and excessive heat.

2. Wire in accordance with the wiring diagram above

OPERATION:

1. With the engine running depress the momentary SET switch S1. The relay will close, the LED will be
illuminated and the engine will continue to run when the key is removed.

2. Remove the key from the ignition. The LED will continue to be illuminated and the engine will continue
to run.

3. Step on the foot brake. The LED will go out and the engine will stop.

4. Start the engine and repeat step 1.

5. Insert the key, turn ignition switch to ON and verify that the engine continues to run when the brake
pedal is depressed.

MODEL 091-155

SAFETY LOCK 3

A Controller To Permit Engine Operation With The Ignition Switch Removed

INSTALLATION AND WIRING INSTRUCTIONS

SINCE 1967, DESIGNERS OF INNOVATIVE PRODUCTS

KUSSMAUL ELECTRONICS COMPANY, INC.

March 11, 2003

631-567-5826, FAX: [phone], TEL: 170 CHERRY AVENUE, WEST SAYVILLE, NEW YORK, 11796-1221 USA