The lightning flash with the arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DO NOT REMOVE THE COVER.
NO USER SERVICEABLE PARTS INSIDE.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the product.
IMPORTANT SAFETY & INSTALLATION INSTRUCTIONS
INSTRUCTIONS PERTAINING TO THE RISK OF FIRE ELECTRIC SHOCK , OR INJURY TO PERSONS
WARNING: When using electric products, basic precautions should
always be followed, including the following:
1. Read all the Safety and Installation Instructions and Explanation
of Graphic Symbols before using the product.
2. This product must be grounded. If it should malfunction or
break down, grounding provides a path of least resistance for
electric current to reduce the risk of electric shock. This product
is equipped with a power supply cord having an equipmentgrounding conductor and a grounding plug. The plug must be
plugged into an appropriate outlet which is properly installed and
grounded in accordance with all local codes and ordinances.
DANGER: Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Do not modify the
plug provided with the product – if it will not t the outlet, have a
proper outlet installed by a qualied electrician. Do not use an
adaptor which defeats the function of the equipment-grounding
conductor. If you are in doubt as to whether the product is properly
grounded, check with a qualied serviceman or electrician.
3. Do not use this product near water – for example, near a bathtub,
washbowl, kitchen sink, in a wet basement, or near a swimming
pool, or the like.
4. This product should only be used with a stand or cart that is
recommended by the manufacturer.
5. This product, either alone or in combination with an amplier and
speakers or headphones, may be capable of producing sound
levels that could cause permanent hearing loss. Do not operate
for a long period of time at a high volume level or a level that is
uncomfortable. If you experience any hearing loss or ringing in
the ears, you should consult an audiologist.
6. This product should be located so that its location or position
does not interfere with its proper ventilation.
7. The product should be located away from heat sources such as
radiators, heat registers, or other products that produce heat.
8. The product should be connected to a power supply only of the
type described in the operating instructions or as marked on the
product.
9. This product may be equipped with a polarized line plug (one
blade wider than the other). This is a safety feature. If you are
unable to insert the plug into the outlet, contact an electrician to
replace your obsolete outlet. Do not defeat the safety purpose of
the plug.
10. The power supply cord of the product should be unplugged
from the outlet when left unused for a long period of time. When
unplugging the power supply cord, do not pull on the cord, but
grasp it by the plug.
11. Care should be taken so that objects do not fall and liquids are
not spilled into the enclosure through openings.
12. The product should be serviced by qualied service personnel
when:
A. The power supply cord or the plug has been damaged;
B. Objects have fallen, or liquid has been spilled into the
product;
C. The product has been exposed to rain;
D. The product does not appear to be operating normally or
exhibits a marked change in performance;
E. The product has been dropped, or the enclosure damaged.
13. Do not attempt to service the product beyond that described in
the user maintenance instructions. All other servicing should be
referred to qualied service personnel.
14. WARNING: Do not place objects on the product’s power supply
cord, or place the product in a position where anyone could trip
over, walk on, or roll anything over cords of any type. Do not
allow the product to rest on or be installed over cords of any type.
Improper installations of this type create the possibility of a re
hazard and/or personal injury.
RADIO AND TELEVISION INTERFERENCE
WARNING: Changes or modications to the instrument not expressly
approved by Young Chang could void your authority to operate the
instrument.
IMPORTANT: When connecting this product to accessories and/or
other equipment use only high quality shielded cables.
NOTE: This instrument has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This instrument
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this instrument does cause harmful interference to radio or television
reception, which can be determined by turning the instrument off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
SAVE THESE INSTRUCTIONS
• Reorient or relocate the receiving antenna.
• Increase the separation between the instrument and the receiver.
• Connect the instrument into an outlet on a circuit other than the
one to which the receiver is connected.
• If necessary consult your dealer or an experienced radio/television
technician for additional suggestions.
The normal function of this product may be disturbed by strong electro
magnetic interference. If so, simply reset the product to resume normal
operation by following the instruction manual. In case the function
could not resume, please use the product in another location.
NOTICE
This apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
AVIS
Le present appareil numerique n’emet pas de bruits radioelectriques
depassant les limites applicables aux appareils numeriques de la
class B prescrites dans le Reglement sur le brouillage radioelectrique
edicte par le ministere des Communications du Canada.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any of the ventilation openings. Install in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat. Allow adequate ventilation for the power adapter. Do not
hide it under a carpet or behind a curtain or place it in an enclosed space where heat buildup can
occur. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.
9) Protect the power cord from being walked on or pinched, particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
10) Only use attachments/accessories specied by the manufacturer.
11) Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
12) Unplug this apparatus during lightning storms or when unused for long periods of
time.
13) Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Warning: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.
Do not expose this equipment to dripping or splashing and ensure that no objects lled with liquids,
such as vases, are placed on the equipment.
To completely disconnect this equipment from the AC Mains, disconnect the power supply cord plug
from the AC receptacle.
ANDANTE CUP110 Demo Song List
ANDANTE CUP110 Voice List
ANDANTE CUP110 Specications
page i
Notes
page ii
Introduction
Congratulations on your purchase of the Kurzweil CUP110. You are certain to enjoy many hours exploring the variety of
features as well as the beautiful preset voices.
The CUP110 is designed with the same sound technology from the world acclaimed Artis and PC3 Series keyboards. It
includes Kurzweil’s new German Grand piano.
Primary Features
●88-Note, Fully-Weighted, Hammer-Action Keyboard
●45 Watt 2-way, 4 Speaker, Stereo Sound System
●New German Grand piano
●88 Preset Voices (including drum kits)
●5 Drum Kits
●Scrolling alphanumeric LED display
●Piano Split Mode
●Transpose and Tuning settings
●Metronome and Tempo buttons
●2 user “Favorite” preset voices
●10 levels of keyboard sensitivity
●Performance Recorder
●Dedicated button to select the Grand Piano voice
●Preset Effects including Reverb, Echo, Delay, and Chorus
●51 Built In Demo Songs
●Stereo Audio Input and Output Jacks
●2 Headphone Jacks
●Standard MIDI In and Out ports
●USB “Plug & Play” Computer Port
●Matching Bench Included
Andante CUP110 Carton Contents
Your new Andante CUP110 carton should have the following:
●CUP110 instrument (main cabinet)
●DC power adapter, with AC power cord
●(2) Instrument stand side panels, (1) pedal unit, (1) back panel
If you are missing any of the above, please contact your Kurzweil dealer. It is always a good idea to save the Andante
CUP110 cartons, in case they are needed for shipment. Follow the procedure on the following pages to assemble the
CUP110.
page 1
Introduction
Assembly Instructions
In addition to the main piano cabinet, your instrument comes with a stand requiring assembly, using the parts shown
below. Two people may be needed to complete the assembly, as the stand must rst rest on the oor and then the
instrument must be securely attached on top of it.
STEP 1:
Place the stand parts on a carpeted oor or blanket. Use the four long bolts to attach the pedal unit to the side panels. Insert the screw caps to cover the bolt ends. Use the four shorter screws to attach the back panel to brackets, as
shown below.
STEP 2:
Move the stand into an upright position and then place the instrument upon it. To avoid possible damage, don’t let the
weight of the body rest on the stand until it is properly aligned and secured with the four screws as shown. Rotate the
pedal adjuster until it comes in rm contact with the oor surface. If the adjuster is not in rm contact with the oor, the
pedal will wobble and cause malfunctions.
page 2
Introduction
STEP 3:
Insert the pedal cable connector into the pedal jack located on the bottom of the keyboard.
Be sure that the connector is inserted in the correct orientation. Make sure that the cable clamp
fastens to the pedal cable.
STEP 4:
Install the headphone hanger as shown in the picture at right.
Power Connection
A DC power adapter supplies the Andante CUP110’s power.
Connect the power adapter to the DC receptacle on the rear panel of the Andante CUP110. Then connect the power
cord to an AC outlet.
CAUTION:
Use only the DC power adapter supplied with the Andante CUP110. Connecting the wrong DC
power adapter could damage the instrument.
If the power adapter is damaged or lost, contact your Kurzweil dealer to order a replacement
After the CUP110 is set up, turn the power on. While the unit is performing its power-up routine some of the front panel
buttons will ash. After a couple of seconds, the display will read 1 Grand Piano. The CUP110 is now ready to play.
Use the Quick Start instructions on the following pages for the basic steps to change Voices or play one of the Demo
Songs.
.
Volume
Before turning on the Andante CUP110, it’s always a good idea to set the volume at its minimum set-
ting (all the way to the left). For a generally comfortable level of volume while playing, set the knob at its
middle position.
The Volume Control is located on the right end of the keyboard. Turn this knob from left to right (clock-wise) to increase the volume. This adjusts the Andante CUP110 speaker and headphone audio volume.
The Volume control does not affect the volume of the sound coming from external sources through the
Audio In jacks on the rear panel.
The AC plug shape will vary
depending on location of use
page 3
Introduction
Headphone Jacks
The CUP110 has two stereo 1/4” headphone jacks located below the keyboard on the left end of the cabinet. Plugging
in headphones provides privacy during practice. Both jacks operate the same so two people can play and hear the
music together. When headphones are connected the CUP110’s speakers are silent.
Quick Start
Playing the Voices
1. Turn on the power.
2. The Voice button LED is lit and the rst voice (1 Grand Piano) is ready to play.
3. There are a number of different voices available. Press the Prev- or Next+ button to step through the
available voices.
Playing a Demo Song
1. Press the Record and Play/Stop buttons together to enter Demo Mode.
2. The rst demo song immediately plays. The CUP110 continues to play each of the demo songs until
you press the Play/Stop button.
3. At any time you can press the Play/Stop button to start or stop playing a demo song.
4. Press the Prev- or Next+ button to play the previous or next demo song.
5. Simultaneously press the Prev- and Next+buttons to jump ahead 10 songs at a time.
6. Press the Voice button to exit Demo Mode.
page 4
Input/Output Panel
The Input/Output panel is located on the rear of the instrument cabinet.
Overview
Audio In and Audio Out
Audio Out (RCA jacks) may be used to connect the Andante CUP110 to external audio equipment, such as an
outboard mixer, powered speakers, or recording device.
Audio In jacks are used to connect the Andante CUP110’s internal speakers to other devices such as
a digital audio player or CD player. Always turn off the CUP110’s power before plugging or unplugging
cables into the Audio In jacks.
The Andante CUP110’s Volume Control does not affect the volume of the sound coming from the Audio
In jacks. Therefore it is best to use a device that has its own output level control and to use that to adjust
the sound volume from the external device.
MIDI In and Out ports
Use the MIDI In and Out ports to connect the Andante CUP110 to other MIDI devices to receive and send
MIDI data.
CC Pedal (Volume/Expression Pedal)
This jack is used to connect a continuous controller pedal for volume and expression control. The CUP110 re-
quires a pedal with a TRS 1/4” connector and 10k linear potentiometer. Most manufacturers EXCEPT Yamaha
and Korg make pedals with the same specications and should work. Yamaha and Korg pedals typically use
an exponential potentiometer and therefore will not work correctly. The CC-1 pedal is available from Kurzweil.
You can order the CC-1 through your local Kurzweil dealer.
USB
Connect a USB cable to this port to send and receive MIDI or to connect to a computer to apply system
updates.
page 5
Overview
Control Panel Display, Buttons and Controls
The features labelled on the Andante CUP110’s front panel below are discussed in detail in the following chapters.
Throughout this manual button names are shown in Bold Type, and display screen text in Italic Type.
Display
The LED screen displays scrolling text indicating the current instrument mode or parameter settings.
Piano Button
No matter which mode is active, you may select this button to immediately return to the Grand Piano voice.
Voice Button
Press this button to enter Voice Mode.
Favorites 1 and 2
Select a previously stored favorite sound by pressing the Favorites
button assigned to it.
Store the current sound by pressing and holding the desired Favor-
itesbutton until the word Saved appears on the display.
Pressing the Favorite 1 + Favorite 2 buttons simultaneously will
initiate PianoSplit Mode.
Metronome Button
Select this button to hear the metronome as you play.
Tempo Button
Use the Tempo button to access the tempo of the metronome, then
make changes with Prev- or Next+ buttons.
Transpose Button
This button will allow you to adjust the tuning of the keyboard in semitones, to a desired interval.
Settings Button
Press the Settings button to enter Settings Mode. Global settings affecting the instrument overall may
be adjusted in this mode.
page 6
Recording and Play/Stop Buttons
Press the Record button to initiate Record Mode.
Select the Play/Stop button to play or stop recording, or play and stop Demo songs or a saved user
song.
Press Record and Play/Stop together to enter Demo Mode.
Prev- and Next+ Buttons
Use these buttons to select the next higher or lower Voice or parameter value. When using the metro-
nome, use these buttons to increase or decrease the tempo. These buttons are also used to tune or
transpose.
Press and hold either button and it will repeat until it is released.
PressingPrev- / Next+ simultaneously allows you to reset certain parameters to a default value, or to
jump quickly through a list of options.
Overview
Operation
The following sections describe how to use the controls for various purposes. Most of the CUP110’s features are organized in groups called modes. The CUP110 has ve operating modes that allow players to congure and apply these
features, and to save settings for later access. The following sections describe each of the operating features:
●DEMO MODE explains how to play the pre-recorded songs in the CUP110.
●VOICE MODE explains how to access the variety of different voices available.
●PIANO SPLIT MODE explains how to divide the keyboard into 2 44-key regions for 4-hand use.
●The TRANSPOSE, METRONOME and TEMPO sections explains how to adjust these features.
●SETTINGS MODE describes a variety of global parameter settings in the CUP110.
●RECORDING explains how to record musical sequences.
●MIDI introduces the Musical Instrument Digital Interface functions in the CUP110.
page 7
Demo Mode
The Andante CUP110 has 51 pre-recorded grand piano songs performed in a variety of classical styles that demon-
strate the Grand Piano Voice. See the Appendix for a complete list of the demo songs and their corresponding
keyboard keys.
Selecting Demo Songs
Press the Record + Play/Stop buttons together to enter Demo Mode. The rst song, a Brahms Rhapsody, will be-
gin to play. Its song number and name will display on the screen. When the rst song ends, the next demo song begins
to play. This will continue through all 51 demo songs.
Press the Play/Stop button to start or stop playing a demo song.
To skip through the demo song list and select a different song to play, press the Prev- button to select the previous
demo song or the Next+ button to select the next demo song. You may press the Play/Stop button to stop the
current demo song, then press the Play/Stop again to start the next demo song selected. To skip forward 10 songs
at a time, press the Prev- / Next+ button pair simulaneously.
Demo Song Select via Keyboard
In Demo Mode, keyboard keys A0 through B4 are assigned to each demo song. To select a demo song
using the keyboard, rst press the Record button then press and release its corresponding key.
To exit Demo Mode, press either the Voice or Piano buttons.
Voice Mode
When you turn on the Andante CUP110, Voice Mode is active and the Grand Piano voice is already selected and
ready to play. Grand Piano is the default voice. The Appendix of this manual provides a complete list of available
voices and their corresponding keyboard keys.
Selecting Voices
If the Andante CUP110 is not already in Voice Mode, press the Voice button to return to your sounds.
To select another voice, press the Prev- or Next+ button to navigate through the available voices.
A complete list of the Voices, with corresponding keyboard keys, is included in the Appendix.
Voice Select via Keyboard
For a direct selection of desired Voices, while in Voice Mode, pressing the Voice button again will cause
the Voice LED to blink, the display will show the scrolling text “Strike a key.” Pressing a keyboard key
at this point will select the Voice that corresponds to that key. The instrument will then return to normal
Voice Mode.
To cancel “Voice Select Via Keyboard Mode” and return to normal without changing the current Voice,
simply select Voice again (or any other button, and you may then perform the normal function of that
button).
Storing a Favorite Voice
You can quickly save any voice as a favorite. Just select a voice then press and hold one of the Favorites buttons.
The voice is now stored in that location.
page 8
Piano Split Mode
Piano Split mode divides the CUP110 keyboard into an upper and lower region, above or below the F4 key. Each
region then functions as a 44-key instrument: the left region is transposed up two octaves; the right is transposed down
two octaves. This allows the instrument to be played with four hands. The left pedal will function as sustain on the left
zone, the right pedal will function as sustain on the right zone.
Entering Piano Split Mode
Pressing the Favorite 1 + Favorite 2 buttons simultaneously will initiate Piano Split Mode. The display will scroll
“PS Piano Split” and then just “PS.” The Favorites buttons will remain lit while in this mode.
Transpose
To enter Transpose Mode press the Transpose button. The Transpose LED will blink, and the Voice LED will turn
off. The display will indicate the current transposition. Pressing the Next+ or Prev- buttons will adjust the transposi-
tion between -24 and 24 in steps of 1 semitone.
Press Prev- /Next+ simultaneously to reset the Transpose value to 0.
To exit Transpose Mode, press Transpose again, or the Voice button, to return to Voice Mode. If the Transpose
value is not 0, the Transpose LED will remain lit, to indicate that the keyboard is currently transposed.
Metronome
When the Metronome button is selected, the metronome will be heard through the piano speakers when playing. It
will be set to its default tempo (120 beats per minute) upon powering on the instrument up but it can range from 20 to
300 BPM. To change the Metronome Volume, see the Settings section of this manual.
Changing the Tempo
To change the metronome tempo, press the Tempo button. Its LED lights and the display shows the current tempo in
beats-per-minute (BPM). Press the Prev- button to decrease the tempo (to a low of 20 BPM) or press the Next+ but-
ton to increase the tempo (up to the maximum of 300 BPM).
While the Tempo button LED remains lit, the display will show the selected tempo. To return to the default setting of
120 BPM, press the Prev- /Next+ button pair. Hitting any other button will exit Tempo mode and the display will show the current Voice number.
Using Tap Tempo
Pressing the Tempo button repeatedly will allow you to set the tempo manually. Your tapping intervals will be
measured and displayed in beats-per-minute.
page 9
Recording
The CUP110’s recorder allows you to record and play back a song.
Start Recording
1. Select the voice you want to use. Press Record.
If the Metronome is turned on when Record is pressed, the Metronome will stop in order for the click or
rhythm to stay synchronized with the recorder when Play is pressed. When Play is pressed, a countoff
click will be heard before recording begins.
2. Press Play/Stop to begin the recording. Perform the song now.
3. Press Play/Stop to end the recording.
Playing the Recording
You can now listen to the song you’ve recorded.
1. Press Play/Stop to listen to your song.
2. Press Play/Stop again to stop the playback.
Erasing the Recording
You can erase the entire song by recording “nothing:”
1. Press Record.
2. Press Play/Stop to begin.
3. Press Play/Stop again.
Punch-Ins
“Punching in” is a way to edit or correct mistakes on a recording without re-recording the entire track.
1. Press Play/Stop to begin playing the song.
2. When the song reaches the part you need to correct, press Record. Play the corrected notes.
3. Press Play/Stop to nish the punch-in.
NOTE: If you don’t press the Play/Stop button after you punch-In, you will erase the remaining portion
of the track.
page 10
Settings Mode
The Settings Mode includes parameters that allow you to change the overall behavior of the entire instrument.
The following parameters are available in Settings Mode:
●Transpose
●Reverb Level
●Touch Sensitivity
●Tune
●MIDI Channel
●Metronome Volume
●Local Control
●Auto Power Off
●Hard Reset
●OS/Object
Selecting and Saving Settings
Press the Settings button to enter Settings Mode. Pressing the Settings button repeatedly allows you to choose
one of the parameters listed above. Once you choose a parameter, you will use the Prev- or Next+ buttons to navi-gate the values of that parameter. Pressing the Voice or Piano button will exit this mode.
Transpose
The Transpose parameter allows you to adjust the overall pitch of the keyboard up or down in semitone intervals.
Press the the Settings button until the screen displays Transpose: (0 is the factory default). To transpose the pitch
up, press the Next+ button for each semitone up in pitch. To lower or transpose down, Press the Prev- button to
lower the semitone pitch. Pressing the Prev- / Next+ button pair will reset the transposition back to factory default of
0. The transposition has a range of -24 to +24. This offers a two octave transposition range up or down.
Reverb Level
The reverb level parameter controls the level of the reverb effects used on a voice. Press the Settings button until the screen reads REVERB LEVEL:20 (factory default). To increase the reverb effect, press the Next+ button. To
decrease the reverb effect press the Prev- button. You can adjust the effect level from 0% (no effect) to 100%. Press-ing the Prev- / Next+ button pair will reset the effect level back to factory default of 20%.
page 11
Settings, con’t
Touch
Use this parameter to adjust the keyboard touch sensitivity to your playing technique.
Press the Settings button until the screen displays Touch:Linear (factory default). To change the setting, press the
Next+ button to advance to the next desired Touch. Press the Prev- button down to reverse the steps. The following
are the available settings:
Linear Best Dynamic Range for all sounds (Factory Default Setting).
Light (1-3) For players with a light touch. Adjust this parameter to achieve a good dynamic range. These settings
Hard (1-3) For players with a heavier touch. Adjust this parameter to achieve a good dynamic range. These set-
Piano Touch Best for piano dynamics.
Easy Touch Light touch, especially for younger players.
GM Receive Select this when playing General MIDI songs.
The Touch setting is remembered across power cycles. Pressing the Prev- / Next+ button pair will reset the Touch
level back to factory default of Linear.
are from Light 1, a slightly light touch, to Light 3, a very light touch.
tings range from Hard 1, a slightly harder touch, to Hard 3, a very hard touch.
Tune
This parameter allows you to adjust the Andante CUP110 tuning to match other instruments or recordings.
Press the Settings button until the display reads TUNE:0 (factory default is A - 440). To increase the tuning, press
the Next+ button from 0 to 100 cents. To lower or reduce the tuning, press the Prev- button from 0 to -100 cents.
Pressing Prev- / Next+ button pair will reset the tuning back to factory default of 0 or A-440.
MIDI Channel
This parameter controls the MIDI transmit channel used for Voice Mode. Press the Settings button until the display
reads CHANNEL: 1 (Factory Default). You can select Channels 1 through 9, or Channels 11 through 15. Channel 16
is reserved for the metronome. Pressing the Prev- / Next+ button pair will reset the MIDI Channel back to the factory
default of 1.
For more information on MIDI, see the following section of this manual.
Metronome Volume
This setting ranges from 1 (lowest) to 9 (loudest). The default setting is 9. In Settings Mode, press the Prev- or
Next+ button to reach the desired volume level. The Metronome setting is remembered across power cycles.
Local Control
When you play the CUP110 keyboard you hear the resident or “local” voices, because this parameter is normally set to On. When using your CUP110 with an external sequencer or computer, turn this setting to Off to avoid creating a MIDI
loop which may result in stuck notes or “echoes”. Press either the Prev- or Next+ button to set this parameter.
Auto Power Off
This energy-saving feature will automatically shut off power to the unit after a period of inactivity. Simply pressing
the power button will power up the unit once again. This allows you to reduce overall power consumption, and also
extends the lifetime of the instrument. Press the Settings button until the display reads AutoPowerOff. Options are
page 12
Settings, con’t
Disabled, 15 min, 30 min, 1 hour, 2 hours or 4 hours. The default value is 30 min. Pressing the Prev- /Next+ but-
ton pair will reset to default.
Hard Reset (Restoring Factory Defaults)
This function resets the Andante CUP110 to the original factory default settings. All user changes, saved Favorites, and user recorded songs are erased. This action cannot be undone.
1. Press the Settings button until the display reads HARD RESET?.
2. To perform the Hard Reset function press the Next+ button once.
3. The display now reads CONFIRM?
4. Press the Next+ button again conrm and to reset the CUP110. The unit will then erase its user
memory, restore all factory settings and reboot.
If you want to cancel the Hard Reset and remain in Settings Mode, press the Prev- button to conrm. Press any other button to exit Settings Mode.
There is an alternate method for a Hard Reset on your Andante CUP110:
1. Hold the C8 key down while switching on the power.
2. Continue to hold C8 down until you see “RESETTING” (scrolling) in the display then release.
OS/Objects Version
To check for possible updates to your operating system in Settings Mode press the Settings button until “OS” is
displayed. This will display the current operating software and objects version.
The display rst shows the OS version, then the Object version. Visit the Kurzweil website (www.kurzweil.com) to verify that your CUP110 has the latest versions. These are located under the Downloads tab for the CUP110. Complete
installation instructions are included in the downloaded les. A standard USB cable will be required for this operation.
page 13
Midi
About MIDI
MIDI is the acronym for Musical Instrument Digital Interface. It is the industry standard protocol which allows the ex-
change of musical data between electronic musical instruments, devices (such as a sequencer), and computers. MIDI
enables MIDI-equipped devices designed by different manufacturers to communicate MIDI data to each other.
MIDI data is sent or received using standard MIDI cables to connect to other MIDI devices or a USB cable to connect to
a computer. The CUP110 is equipped with conventional MIDI In and Out ports, and a USB port. The Andante CUP110
has a standard class-compliant USB-MIDI implementation. It does not require the installation of any additional drivers.
MIDI Channels
Similar to television channels, MIDI protocol transmits multiple channels of MIDI performance data. Typical MIDI instruments can play up to 16 channels at the same time. Each channel can be assigned its own voice.
To change and/or assign MIDI channels, enter Settings Mode and select the MIDI Channel parameter. See the MIDI
Implementation chart at the end of this chapter for details.
MIDI In and Out Ports
The CUP110 is equipped with the conventional MIDI In and Out ports. The MIDI In port is used to receive MIDI
data from another MIDI device; the MIDI Out port is used to transmit the MIDI data generated by the CUP110 to
another MIDI device; the MIDI Thru port passes MIDI In data along to an external device.
When you connect the MIDI Out of the CUP110 to the MIDI In of another instrument, you can play the sounds of
both instruments simultaneously from the CUP110’s keyboard.
When you connect the MIDI In of the CUP110 to the MIDI Out of another controller, you can control the CUP110 using
the other controller.
page 14
Midi, con’t
USB MIDI Connection
In addition to the conventional MIDI In and Out ports, the Andante CUP110 also has a USB (Universal Serial Bus) port
on the panel on the back of the piano. You can connect the CUP110 directly to a computer with a USB cable. This con-
nection transmits and receives MIDI data between the CUP110 and the computer.
The Andante CUP110 supports the “Plug and Play” feature used in the Windows XP or higher and Macintosh operating
systems. No drivers are required to use this connection; but you may need to enable MIDI on your computer’s sound
and audio control panel.
To use the Andante CUP110 as a MIDI controller with a computer, use any Type-A to Type-B USB cable. By default,
the CUP110 acts as a MIDI controller (not a hard drive) when connected to a computer.
If you have a sequencer program installed on your computer, you can use this USB connection to record and play
your music. The Andante CUP110‘s recorder is actually a simple sequencer and the performance you record into the
CUP110’s memory is MIDI performance data. Using a computer-based sequencer program provides unlimited memo-
ry, editing, and the ability to post on the Internet.
Using Windows applications for MIDI control
Certain apps (like Windows Media Player - WMP) released with Windows Vista or later can no longer play MIDI songs
triggering external MIDI devices; WMP is only routed to the internal Microsoft GS Synthesizer.
This means the MIDI app you choose to use must natively offer its own built-in MIDI mapping abilities. Most commercial MIDI software products for PC have a conguration screen which includes the MIDI device mapping necessary to
route to an external MIDI device such as the Andante CUP110.
1RhapsodyA0J. Brahms
2Prelude IA#0J. S. Bach
3Invention No. 4B0J. S. Bach
4Invention No. 8C1J. S. Bach
5Prelude IIC#1J. S. Bach
6Aria GoldbergD1J. S. Bach
7Fuga IID#1J. S. Bach
8Sonatine Op.36E1M. Clementi
9F1W. A. Mozart
10Piano SonateF#1W. A. Mozart
11Rondo in DG1W. A. Mozart
12Piano Sonate K.3G#1W. A. Mozart
13Piano Sonate K.5A1W. A. Mozart
14Minuet in GA#1L. V. Beethoven
15Bagatelle No. 25B1L. V. Beethoven
16Sonatine Op.55C2Fr. Kuhlau
17March MilitaireC#2F. P. Schubert
18Moments MusicauxD2F. P. Schubert
19Impromptu No. 2D#2F. P. Schubert
20Impromptu No. 4E2F. P. Schubert
21La ChevaleresqueF2ler
22Without wordsF#2J. L. F. Mendelssohn
23VenetianischesG2J. L. F. Mendelssohn
24SostenutoG#2F. F. Chopin
25Valse KKA2F. F. Chopin
265 MazurkasA#2F. F. Chopin
27Valse Op.69 No. 2B2F. F. Chopin
28Grande ValseC3F. F. Chopin
29Valse Op.64 No. 2C#3F. F. Chopin
30Nocturne No. 2D3F. F. Chopin
31Valse Op.64 No. 1D#3F. F. Chopin
32Preludes in DbE3F. F. Chopin
33Fantaisie-ImpromF3F. F. Chopin
34F#3R. Schumann
35G3R. Schumann
36G#3R. Schumann
37A3F. Liszt
38Dolly
39stimmenB3J. Strauss
40The SwanC4Saint-
41BlumenliedC#4G. Lange
42ValsetteD4F. Borowski
43Old French AirD#4P. I. Tchaikovsky
44MazurkaE4P. I. Tchaikovsky
45PolkaF4P. I. Tchaikovsky
46BarcarolleF#4P. I. Tchaikovsky
47HumoreskaG4A. Dvorak
48Suite Peer GyntG#4E. Grieg
49Suite BergamasqueA4C. A. Debussy
50RêverieA#4C. A. Debussy
51 Arabesque I
Song Name
s Dreaming
Key
A#3T. Oesten
B4
C. A. Debussy
Composer
page 17
Appendix
ANDANTE CUP110 Voice List
NO.KEYVOICENO.VOICE
1A0Grand Piano 45F4Flute
2A#0Bright Piano 46F#4Horns+Str
3B0Concert Piano 47G4Winds+Str
4C1Jazz Piano 48G#4Gothic Orch
5C#1Piano & Pad 49A4Silver Orch
6D1Piano & Vox 50A#4Pastoral Orch
7D#1Piano & Strings 51B4Victory Orch
8E1Blues Piano 52C5Imperial Orch
9F1Rock Piano53C#5Vivaldi Orch
10F#1Upright Piano 54D5Magic Orch
11G1Piano, Bass & Ride **55D#5LA Strings
12G#1Piano & Bass **56E5Oct Strings
13A1Piano Split **57F5Pizzicato
14A#1Stevie's EP58F#5Adagio Str
15B1These Eyes EP59G5Tremolando
16C2Hotrod EP60G#5Fast Strings
17C#2E Piano+Pad61A5Solo Violin
18D2Supertramp EP62A#5Solo Viola
19D#2Woodstock 63B5Solo Cello
20E2Classic DX 64C6Full Choir
21F2FM E Piano65C#6Aah Vocals
22F#2Classic 70's66D6Jazzy Scat
23G2E Piano & EBass **67D#6Synth Vox
24G#2FM Piano & EBass **68E6E-Bass
25A2Crisp Clav69F6Slap Bass
26A#2Steely Clav70F#6Fretless Bass
27B2Wah Clav71G6Upright Bass
28C3Fuzz Clav72G#6AC Guitar
29C#3Harpsichord73A6Nylon Guitar
30D3Mellow Organ74A#6Chorus Guitar
31D#3Sweet Organ75B6Lead Guitar
32E3Perc Organ76C7Xylophone
33F3Gregg's B77C#7Marimba
34F#3Blues+Gospel78D7Vibraphone
35G3Gospel B79D#7Koto
36G#3Farsa 80E7Mbira
37A3Pipe Stops81F7Sitar
38A#3Chapel Organ82F#7Harp/Mallets
39B3All Stops 83G7Steel Drums
40C4AllStop Choir84G#7Solid Kit
41C#4Pop Horns85A7Latin Kit
42D4Salsa Horns86A#7Electric Kit
43D#4Trumpet 87B7Brush Kit
44E4Tenor Sax 88C8Percussion
** HIGHLIGHTED ROWS INDICATE VOICE PAIRS THAT TRANSMIT OVER SEPARATE MIDI CHANNELS; THESE CANNOT BE SELECTED DIRECTLY OVER MIDI
page 18
ANDANTE CUP110 Specications
Appendix
Keyboard
Preset Programs
Piano Split Mode
Effects
Recorder
Sound System
Headphones
I/O Jacks
USB
Pedals
Polyphony
Finish
Dimensions
Weight
Power
88 Note, hammer-action keyboard with adjustable touch sensitive keys.
88 Expressive sounds, including new German Grand Piano.
Dual 44-key operation
Dual ambience and effect processors (reverberation and chorus). Rich and